[hylafax-users] Can't send faxes any longer.

["Erik P. Olsen" <erik@xxxxxx>]

I don't know what has caused it but I can no longer send faxes. Maybe an
update of Fedora Core 2 has done the harm.

Please find below /var/spool/hylafax/etc/config.ttyS1, syslog and
/var/spool/hylafax/doneq/q29. The latter has a line saying: 
status:/bin/cat: write error: Broken pipe\

I don't what that means but it doesn't look healthy.

Could someone, please, shed some light in this darkness.

Thanks in advance.



/var/spool/hylafax/etc/config.ttyS1:

# $Id: class1.0,v 1.1 2002/05/23 21:32:18 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software
and 
# its documentation for any purpose is hereby granted without fee,
provided
# that (i) the above copyright notices and this permission notice appear
in
# all copies of the software and related documentation, and (ii) the
names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY
KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY
OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Generic Class 1.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		45
AreaCode:		
FAXNumber:		+4538346470
LongDistancePrefix:	
InternationalPrefix:	00
DialStringRules:	etc/dialrules.europe
ServerTracing:		15
SessionTracing:		15
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		99
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
# We use "ModemType: Class1" with "Class1Cmd: AT+FCLASS=1.0" for now
#
ModemType:		Class1		# use this to supply a hint
#ModemRate:		19200		# rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
#GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemSoftResetCmdDelay:	3000	# pause after soft reset
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
Class1Cmd:		AT+FCLASS=1.0	# command to enter class 1.0
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait before PPM
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait before TCF
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait before EOP
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & response
Class1SendMsgDelay:	75		# 75ms delay after training
Class1SwitchingDelay:	75		# 150ms delay in switching transmission
direction
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration

Syslog:

Aug 24 22:20:50 localhost FaxQueuer[1989]: SUBMIT JOB 24
Aug 24 22:20:50 localhost FaxGetty[2199]: LOCKWAIT
Aug 24 22:20:53 localhost FaxQueuer[2592]: JOB 24: CONVERT DOCUMENT:
exit status 0xff00
Aug 24 22:20:53 localhost FaxQueuer[1989]: NOTIFY: bin/notify
"doneq/q24" "no_formatter" ""
Aug 24 22:20:53 localhost FaxQueuer[1989]: NOTIFY exit status: 0 (2596)
Aug 24 22:21:21 localhost FaxGetty[2199]: MODEM set DTR OFF
Aug 24 22:21:21 localhost FaxGetty[2199]: DELAY 75 ms
Aug 24 22:21:21 localhost FaxGetty[2199]: MODEM set DTR ON
Aug 24 22:21:21 localhost FaxGetty[2199]: DELAY 2600 ms
Aug 24 22:21:24 localhost FaxGetty[2199]: MODEM set baud rate: 19200
baud, input flow XON/XOFF, output flow XON/XOFF
Aug 24 22:21:24 localhost FaxGetty[2199]: DELAY 10 ms
Aug 24 22:21:24 localhost FaxGetty[2199]: MODEM flush i/o
Aug 24 22:21:24 localhost FaxGetty[2199]: <-- [4:ATZ\r]
Aug 24 22:21:24 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:24 localhost FaxGetty[2199]: DELAY 3000 ms
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [5:ATE0\r]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [4:ATE0]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [5:ATV1\r]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [5:ATQ0\r]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [7:ATS0=0\r]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [7:ATS8=2\r]
Aug 24 22:21:27 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:27 localhost FaxGetty[2199]: <-- [8:ATS7=60\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [12:AT+FCLASS=?\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [7:0,1,1.0]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [14:AT+FCLASS=1.0\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [5:ATI3\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [28:LASAT safire 560 Voice
V1.21]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [5:ATI0\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [5:56000]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [9:AT+FTM=?\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [9:AT+FRM=?\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [14:AT+FCLASS=1.0\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: MODEM LASAT SAFIRE 560 VOICE
V1.21 56000/
Aug 24 22:21:28 localhost FaxGetty[2199]: <-- [5:ATM0\r]
Aug 24 22:21:28 localhost FaxGetty[2199]: --> [2:OK]
Aug 24 22:21:28 localhost FaxGetty[2199]: MODEM input buffering disabled

/var/spool/hylafax/doneq/q29:

tts:1093385894
killtime:1093396632
retrytime:0
state:8
npages:0
totpages:0
ntries:0
ndials:0
totdials:0
maxdials:12
tottries:0
maxtries:3
pagewidth:209
resolution:196
pagelength:296
priority:127
schedpri:127
minsp:0
desiredbr:13
desiredst:0
desiredec:1
desireddf:3
desiredtl:0
useccover:1
external:40765300
number:40765300
mailaddr:erik@xxxxxxxxxxxxxxxxxxxxx
sender:Erik P. Olsen
jobid:29
jobtag:
pagehandling:
modem:any
receiver:
company:
location:
cover:
client:localhost.localdomain
owner:erik
groupid:29
signalrate:
dataformat:
jobtype:facsimile
tagline:
subaddr:
passwd:
doneop:default
commid:
status:/bin/cat: write error: Broken pipe\

notify:none
pagechop:default
chopthreshold:3
postscript:0::docq/doc43.ps.29


-- 
Regards,
Erik P. Olsen


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*