Re: [hylafax-users] US Robotics 56K Send FAX problem MODEM TIMEOUT: writing to modem

["Sundaram Ramasamy" <sun@xxxxxxxxxxxx>]

Title: Message

Hi all,

 

I am getting Modem Timeout while sending the fax.

 

OS: Suse 9.2 with external US Roboties 56K FAX modem

 

hylafax-4.1.7-67

kdegraphics3-fax-3.1.4-39

capi4hylafax-4.1.7-67

printfax-1.4.2-606

 

 

mail:/var/spool/fax/etc # ps -fed |grep fax

fax       2674     1  0 17:55 ?        00:00:00 /usr/sbin/faxq

fax       2677     1  0 17:55 ?        00:00:00 /usr/lib/fax/hfaxd -i hylafax -o 4557 -s 444

fax       3703     1  1 21:55 ?        00:00:00 /usr/lib/fax/faxgetty /dev/ttyS1

root      3705  2488  0 21:55 pts/4    00:00:00 grep fax

 

===

OK

at+fclass=?

 

0,1,2.0

 

 

 

Log message:

========

 

Nov 14 00:30:58.68: [ 2549]: SESSION BEGIN 00000052 16147512018

Nov 14 00:30:58.68: [ 2549]: HylaFAX (tm) Version 4.1.7

Nov 14 00:30:58.68: [ 2549]: SEND FAX: JOB 18 DEST 7512018 COMMID 00000052 DEVICE '/dev/ttyS1'

Nov 14 00:30:58.68: [ 2549]: MODEM set DTR OFF

Nov 14 00:30:58.68: [ 2549]: DELAY 75 ms

Nov 14 00:30:58.75: [ 2549]: MODEM set DTR ON

Nov 14 00:30:58.75: [ 2549]: DELAY 2600 ms

Nov 14 00:31:02.35: [ 2549]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF

Nov 14 00:31:02.35: [ 2549]: DELAY 10 ms

Nov 14 00:31:02.36: [ 2549]: MODEM flush i/o

Nov 14 00:31:02.36: [ 2549]: <-- [4:ATZ\r]

Nov 14 00:31:02.49: [ 2549]: --> [2:OK]

Nov 14 00:31:02.49: [ 2549]: DELAY 3000 ms

Nov 14 00:31:05.49: [ 2549]: <-- [5:ATE0\r]

Nov 14 00:31:05.62: [ 2549]: --> [2:OK]

Nov 14 00:31:05.62: [ 2549]: <-- [5:ATV1\r]

Nov 14 00:31:05.74: [ 2549]: --> [2:OK]

Nov 14 00:31:05.74: [ 2549]: <-- [7:ATQ0X4\r]

Nov 14 00:31:05.88: [ 2549]: --> [2:OK]

Nov 14 00:31:05.88: [ 2549]: <-- [7:ATS0=0\r]

Nov 14 00:31:06.01: [ 2549]: --> [2:OK]

Nov 14 00:31:06.01: [ 2549]: <-- [7:ATS8=2\r]

Nov 14 00:31:06.15: [ 2549]: --> [2:OK]

Nov 14 00:31:06.15: [ 2549]: <-- [8:ATS7=60\r]

Nov 14 00:31:06.27: [ 2549]: --> [2:OK]

Nov 14 00:31:06.27: [ 2549]: <-- [12:AT&H2&I2&R1\r]

Nov 14 00:31:06.41: [ 2549]: --> [2:OK]

Nov 14 00:31:06.41: [ 2549]: <-- [11:ATS13=1&D2\r]

Nov 14 00:31:06.55: [ 2549]: --> [2:OK]

Nov 14 00:31:06.55: [ 2549]: <-- [6:AT&C1\r]

Nov 14 00:31:06.68: [ 2549]: --> [2:OK]

Nov 14 00:31:06.68: [ 2549]: <-- [12:AT+FCLASS=1\r]

Nov 14 00:31:06.82: [ 2549]: --> [2:OK]

Nov 14 00:31:06.82: [ 2549]: <-- [12:AT+FCLASS=0\r]

Nov 14 00:31:06.96: [ 2549]: --> [2:OK]

Nov 14 00:31:06.96: [ 2549]: <-- [5:ATM0\r]

Nov 14 00:31:07.09: [ 2549]: --> [2:OK]

Nov 14 00:31:07.09: [ 2549]: STATE CHANGE: RUNNING -> SENDING

Nov 14 00:31:07.09: [ 2549]: MODEM input buffering enabled

Nov 14 00:31:07.09: [ 2549]: Apply DialString rules to "7512018"

Nov 14 00:31:07.09: [ 2549]: --> return result "7512018"

Nov 14 00:31:07.09: [ 2549]: <-- [12:AT+FCLASS=1\r]

Nov 14 00:31:07.33: [ 2549]: --> [2:OK]

Nov 14 00:31:07.33: [ 2549]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled

Nov 14 00:31:07.33: [ 2549]: DIAL 7512018

Nov 14 00:31:07.33: [ 2549]: <-- [12:ATDT7512018\r]

Nov 14 00:31:19.00: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:19.00: [ 2549]: MODEM input buffering disabled

Nov 14 00:31:20.02: [ 2549]: --> HDLC<25:FF C0 02 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04 7C F4>

Nov 14 00:31:20.02: [ 2549]: --> [2:OK]

Nov 14 00:31:20.02: [ 2549]: REMOTE CSI "NothingSetup"

Nov 14 00:31:20.02: [ 2549]: <-- [9:AT+FRH=3\r]

Nov 14 00:31:20.03: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:20.42: [ 2549]: --> HDLC<12:FF C8 01 00 77 5F 01 79 03 C0 BC A1>

Nov 14 00:31:20.42: [ 2549]: --> [2:OK]

Nov 14 00:31:20.42: [ 2549]: REMOTE best rate 14400 bit/s

Nov 14 00:31:20.42: [ 2549]: REMOTE max page width 2432 pixels in 303 mm

Nov 14 00:31:20.42: [ 2549]: REMOTE max unlimited page length

Nov 14 00:31:20.42: [ 2549]: REMOTE best vres 7.7 line/mm

Nov 14 00:31:20.42: [ 2549]: REMOTE best format 2-D MR

Nov 14 00:31:20.42: [ 2549]: REMOTE best 0 ms/scanline

Nov 14 00:31:20.42: [ 2549]: USE 14400 bit/s

Nov 14 00:31:20.42: [ 2549]: USE 0 ms/scanline

Nov 14 00:31:20.42: [ 2549]: SEND file "docq/doc24.ps;70"

Nov 14 00:31:20.42: [ 2549]: USE page width 1728 pixels in 215 mm

Nov 14 00:31:20.42: [ 2549]: USE unlimited page length

Nov 14 00:31:20.42: [ 2549]: USE 3.85 line/mm

Nov 14 00:31:20.42: [ 2549]: USE 2-D MR

Nov 14 00:31:20.42: [ 2549]: SEND training at v.17 14400 bit/s

Nov 14 00:31:20.42: [ 2549]: <-- [9:AT+FTH=3\r]

Nov 14 00:31:20.61: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:20.62: [ 2549]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04>

Nov 14 00:31:20.62: [ 2549]: <-- data [23]

Nov 14 00:31:20.62: [ 2549]: <-- data [2]

Nov 14 00:31:20.64: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:20.64: [ 2549]: <-- HDLC<6:FF C8 C1 00 45 1E>

Nov 14 00:31:20.64: [ 2549]: <-- data [6]

Nov 14 00:31:20.64: [ 2549]: <-- data [2]

Nov 14 00:31:22.57: [ 2549]: --> [2:OK]

Nov 14 00:31:22.57: [ 2549]: <-- [9:AT+FTS=7\r]

Nov 14 00:31:22.64: [ 2549]: --> [2:OK]

Nov 14 00:31:22.64: [ 2549]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled

Nov 14 00:31:22.64: [ 2549]: <-- [11:AT+FTM=145\r]

Nov 14 00:31:24.11: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:24.11: [ 2549]: <-- data [1024]

Nov 14 00:31:24.11: [ 2549]: <-- data [1024]

Nov 14 00:31:24.11: [ 2549]: <-- data [652]

Nov 14 00:31:24.11: [ 2549]: <-- data [2]

Nov 14 00:31:25.60: [ 2549]: --> [2:OK]

Nov 14 00:31:25.60: [ 2549]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled

Nov 14 00:31:25.60: [ 2549]: <-- [9:AT+FRS=1\r]

Nov 14 00:31:25.62: [ 2549]: --> [2:OK]

Nov 14 00:31:25.62: [ 2549]: <-- [9:AT+FRH=3\r]

Nov 14 00:31:26.00: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:26.53: [ 2549]: --> HDLC<5:FF C8 21 57 BE>

Nov 14 00:31:26.53: [ 2549]: --> [2:OK]

Nov 14 00:31:26.53: [ 2549]: TRAINING succeeded

Nov 14 00:31:26.53: [ 2549]: DELAY 75 ms

Nov 14 00:31:26.61: [ 2549]: <-- [11:AT+FTM=146\r]

Nov 14 00:31:26.85: [ 2549]: --> [7:CONNECT]

Nov 14 00:31:26.85: [ 2549]: SEND begin page

Nov 14 00:31:26.85: [ 2549]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled

Nov 14 00:31:26.86: [ 2549]: <-- data [1028]

Nov 14 00:31:26.86: [ 2549]: <-- data [1041]

Nov 14 00:31:26.86: [ 2549]: <-- data [1032]

Nov 14 00:31:26.86: [ 2549]: <-- data [1033]

Nov 14 00:32:26.85: [ 2549]: MODEM TIMEOUT: writing to modem

Nov 14 00:32:26.85: [ 2549]: MODEM WRITE SHORT: sent 1033, wrote 1010

Nov 14 00:32:26.85: [ 2549]: SENT 21021 bytes of data

Nov 14 00:32:26.86: [ 2549]: SEND end page

Nov 14 00:32:26.86: [ 2549]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled

Nov 14 00:32:26.86: [ 2549]: <-- [9:AT+FTH=3\r]

Nov 14 00:32:29.40: [ 2549]: --> [0:]

Nov 14 00:32:29.40: [ 2549]: MODEM TIMEOUT: sending HDLC frame

Nov 14 00:32:29.40: [ 2549]: MODEM input buffering enabled

Nov 14 00:32:29.41: [ 2549]: <-- [5:ATH0\r]

Nov 14 00:32:34.40: [ 2549]: MODEM TIMEOUT: reading line from modem

Nov 14 00:32:34.40: [ 2549]: MODEM <Timeout>

Nov 14 00:32:34.40: [ 2549]: MODEM set DTR OFF

Nov 14 00:32:34.41: [ 2549]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)

Nov 14 00:32:34.41: [ 2549]: SESSION END

 

Modem Configuration:

#

# Configuration for using the Class 1 command interface with

# a USR Courier or Sportster modem and XON/XOFF flow control.

#

#

CountryCode:                1

AreaCode:                     614

FAXNumber:                  ""

LongDistancePrefix:       1

InternationalPrefix:         011

DialStringRules: "etc/dialrules"

ServerTracing:                0xFFF

SessionTracing:             0xffffffff

RecvFileMode:               0600

LogFileMode:                 0600

DeviceMode:                  0600

RingsBeforeAnswer:       0

SpeakerVolume:                        off

GettyArgs:                    "-h %l dx_%s"

LocalIdentifier:   "NothingSetup"

TagLineFont:                 etc/lutRS18.pcf

TagLineFormat:              "From %%l|%c|Page %%P of %%T"

MaxRecvPages:             50

#

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType:                 Class1              # use class 1 interface

ModemRate:                  19200               # rate for DCE-DTE communication

ModemFlowControl:       xonxoff              # software flow control

#

ModemSetupDTRCmd:   ATS13=1&D2    # setup so DTR drop resets modem

ModemSetupDCDCmd:  AT&C1              # setup so DCD reflects carrier (or not)

ModemNoFlowCmd:                   AT&H0&I0&R1   # setup modem for no flow control

ModemHardFlowCmd:    AT&H1&I0&R2   # setup modem for hardware flow control

ModemSoftFlowCmd:     AT&H2&I2&R1   # setup modem for software flow control

ModemResultCodesCmd:           ATQ0X4                        # enable result codes

#

ModemMfrQueryCmd:    !USR

ModemModelQueryCmd:            ATI3

ModemRevQueryCmd:    ATI7                  # XXX returns a multi-line result

#

# When AT+FCLASS=1 is issued the modem automatically switches

# to software flow control; these parameters let the fax software

# reset flow control as needed after entering Class 1.

#

Class1NFLOCmd:                      AT&H0&I0&R1   # setup modem for no flow control

Class1HFLOCmd:                      AT&H1&I0&R2   # setup modem for hardware flow control

Class1SFLOCmd:                      ""                      # modem does this automatically

#

# This should resolve "DIS/DTC received 3 times" errors:

#

Class1ResponseWaitCmd:         AT+FRS=1        # wait after sending TCF for response

#

# The remainder of this configuration is included so that the

# modem "idles" in Class 0 while not sending or receiving facsimile.

#

ModemSetupAACmd:     AT+FCLASS=0  # leave modem idling in class 0

ModemAnswerCmd:                   AT+FCLASS=1A           # answer in Class 1

#

# Disables the reporting of bad frames by the modem.  This

# overcomes a firmware problem in the x2 and V90 Sportsters.

# It is not necessary for the Courier modem.

#

Class2NRCmd:    AT+FNR=1,1,1,0

Disclaimer

******************************************************************************

This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message, you are hereby notified that you must not disseminate, copy, or take any action in reliance on it. If you have received this message in error, please notify Morris International immediately and delete all copies. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of Morris International.

******************************************************************************