Re: [hylafax-users] recieve error with terboline19k2 modem

[Volker Weber <hylafax@xxxxxxxxxxxxxxxxxx>]

Lee Howard wrote:
> On 2004.03.11 02:45 Volker Weber wrote:
>
> > i have three logs attched, the first one created a corrupt tiff (
> > file says: "TIFF image data, little-endian", but i cant display or 
> > convert it ).
> > the second an third came from teh same sender and produced no output 
> > (tiff file).
> >
> > any hints?
>
>
> > Mar 11 10:43:50.54: [  519]: RECV: 57 total lines, 53 bad lines, 34 
> > consecutive
> > bad lines
>
>
> > Mar 11 10:48:21.69: [  519]: RECV: 962 total lines, 620 bad lines, 109 
> > consecutive bad lines
>
>
> You may need to use:
>
> ModemRecvFillOrder: LSB2MSB
>
> Lee.

I have this in my config.ttyS0 file.

here is the complete content:

# $Id: skel,v 1.4 2002/04/07 20:29:27 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the 
names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            49
AreaCode:               441
FAXNumber:              +49.441.6834891
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      0
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Volker Weber"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l +49 441 6834891|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # RTS/CTS flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier 
(or not)
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDT%s          # T for tone dialing
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:         ATZ             # stuff to do when modem is reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT&K            # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH0            # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for 
transmit

Class2RecvDataTrigger: "\022"

--
-------------------------------------------------------------------------
      Volker Weber  Dietrichsweg 38a   26127 Oldenburg   Germany
      MAILTO:Volker@xxxxxxxxxxxxxxxxxx     HTTP://www.v-weber.de


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*