 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] T.30 T2 timeout, expected page not received
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] T.30 T2 timeout, expected page not received
- From: Pignedoli Luca <lpignedoli@xxxxxxxx>
- Reply-to: lpignedoli@xxxxxxxx
- Date: Tue, 02 Mar 2004 18:42:28 +0100
Hi. I am running hylafax v4.1.8 on a Linux machine with kernel version 2.4.24. The modem is a USR Robotics 56K FaxModems. Every a lot does not received fax for one a little clear reason.
This is the log file:
Mar 01 17:57:00.71: [ 3501]: SESSION BEGIN 00000076
Mar 01 17:57:00.71: [ 3501]: HylaFAX (tm) Version 4.1.8
Mar 01 17:57:00.71: [ 3501]: <-- [13:AT+FCLASS=1A\r]
Mar 01 17:57:06.00: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:06.00: [ 3501]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Mar 01 17:57:06.00: [ 3501]: RECV FAX: begin
Mar 01 17:57:06.00: [ 3501]: <-- data [23]
Mar 01 17:57:06.00: [ 3501]: <-- data [2]
Mar 01 17:57:06.03: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:06.03: [ 3501]: <-- data [10]
Mar 01 17:57:06.03: [ 3501]: <-- data [2]
Mar 01 17:57:07.98: [ 3501]: --> [2:OK]
Mar 01 17:57:07.98: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:08.21: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:09.76: [ 3501]: --> [2:OK]
Mar 01 17:57:09.76: [ 3501]: REMOTE TSI "XXXX XXXX XXXXX"
Mar 01 17:57:09.76: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:09.78: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:10.05: [ 3501]: --> [2:OK]
Mar 01 17:57:10.05: [ 3501]: REMOTE wants 14400 bit/s
Mar 01 17:57:10.05: [ 3501]: REMOTE wants page width 1728 pixels in 215 mm
Mar 01 17:57:10.05: [ 3501]: REMOTE wants unlimited page length
Mar 01 17:57:10.05: [ 3501]: REMOTE wants 7.7 line/mm
Mar 01 17:57:10.05: [ 3501]: REMOTE wants 2-D MR
Mar 01 17:57:10.05: [ 3501]: RECV training at v.17 14400 bit/s
Mar 01 17:57:10.05: [ 3501]: <-- [11:AT+FRM=145\r]
Mar 01 17:57:11.71: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:13.27: [ 3501]: RECV: TCF 2812 bytes, 3% non-zero, 2704 zero-run
Mar 01 17:57:13.28: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:13.28: [ 3501]: DELAY 75 ms
Mar 01 17:57:13.36: [ 3501]: TRAINING succeeded
Mar 01 17:57:13.36: [ 3501]: <-- [9:AT+FTH=3\r]
Mar 01 17:57:13.56: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:13.56: [ 3501]: <-- data [3]
Mar 01 17:57:13.56: [ 3501]: <-- data [2]
Mar 01 17:57:14.74: [ 3501]: --> [2:OK]
Mar 01 17:57:14.74: [ 3501]: <-- [11:AT+FRM=146\r]
Mar 01 17:57:15.73: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:15.73: [ 3501]: RECV: begin page
Mar 01 17:57:30.58: [ 3501]: RECV: 620 total lines, 0 bad lines, 0 consecutive bad lines
Mar 01 17:57:30.58: [ 3501]: RECV: end page
Mar 01 17:57:30.58: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:30.58: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.17: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.17: [ 3501]: MODEM No carrier
Mar 01 17:57:42.17: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.19: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.19: [ 3501]: MODEM No carrier
Mar 01 17:57:42.19: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.21: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.21: [ 3501]: MODEM No carrier
Mar 01 17:57:42.21: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.23: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.23: [ 3501]: MODEM No carrier
Mar 01 17:57:42.23: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.25: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.25: [ 3501]: MODEM No carrier
Mar 01 17:57:42.25: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.27: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.27: [ 3501]: MODEM No carrier
Mar 01 17:57:42.27: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.29: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.29: [ 3501]: MODEM No carrier
Mar 01 17:57:42.29: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.31: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.31: [ 3501]: MODEM No carrier
Mar 01 17:57:42.31: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.33: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.33: [ 3501]: MODEM No carrier
Mar 01 17:57:42.33: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:42.35: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:42.35: [ 3501]: MODEM No carrier
Mar 01 17:57:42.35: [ 3501]: <-- [9:AT+FRH=3\r]
......
Mar 01 17:57:49.97: [ 3501]: MODEM No carrier
Mar 01 17:57:49.97: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:49.99: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:49.99: [ 3501]: MODEM No carrier
Mar 01 17:57:49.99: [ 3501]: <-- [9:AT+FRH=3\r]
Mar 01 17:57:50.01: [ 3501]: --> [10:NO CARRIER]
Mar 01 17:57:50.01: [ 3501]: MODEM No carrier
Mar 01 17:57:50.01: [ 3501]: RECV FAX (00000076): recvq/fax00076.tif from XXX XXXX XXXX, route to <unspecified>, 0 pages in 0:44
Mar 01 17:57:50.01: [ 3501]: RECV FAX: T.30 T2 timeout, expected page not received
Mar 01 17:57:50.01: [ 3501]: <-- [9:AT+FTH=3\r]
Mar 01 17:57:50.21: [ 3501]: --> [7:CONNECT]
Mar 01 17:57:50.21: [ 3501]: <-- data [3]
Mar 01 17:57:50.21: [ 3501]: <-- data [2]
Mar 01 17:57:51.39: [ 3501]: --> [2:OK]
Mar 01 17:57:51.39: [ 3501]: RECV FAX (00000076): session with XXXX XXXX XXXX terminated abnormally: T.30 T2 timeout, expected page not received
Mar 01 17:57:51.39: [ 3501]: RECV FAX: bin/faxrcvd "recvq/fax00076.tif" "ttyS0" "00000076" "T.30 T2 timeout, expected page not received" "" ""
Mar 01 17:57:51.56: [ 3501]: RECV FAX: end
Mar 01 17:57:51.56: [ 3501]: SESSION END
This is my config.modem
CountryCode: XX
AreaCode: XXXX
FAXNumber: XXXXXXXXXXXXX
LongDistancePrefix: 0
InternationalPrefix: 0
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 2
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: ""
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
PercentGoodLines: 50
MaxConsecutiveBadLines: 10
MaxRecvPages: 100
#
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 115200 # DCE-DTE communication rate
ModemFlowControl: rtscts # hardware flow control
ModemDialCmd: ATDT0%s
#
#ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
#ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
#
#ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#ModemResultCodesCmd: ATQ0X4 # enable extended result codes
ModemResultCodesCmd: ATQ0X3 # enable extended result codes
#ModemSetupAACmd: AT+FAA=1
#ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
Class2BUGCmd: AT+FBU=0
Class2CQQueryCmd: !(0),(0) # override modem response
Class2NRCmd: AT+FNR=1,1,1,0
Class2SendRTC: yes
Class2APQueryCmd: none
Please Help me. :(. Thanks in advance and sorry for my bad English.
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
- Prev by Date: [hylafax-users] Problems sending faxes
- Next by Date: [hylafax-users] Multiple Modems
- Previous by thread: [hylafax-users] T.30 T2 timeout, expected page not received
- Next by thread: [hylafax-users] metamail
- Index(es):
Project hosted by iFAX Solutions