Re: [hylafax-users] Freeware problem report

[Lee Howard <faxguy@xxxxxxxxxxxxxxxx>]

On 2003.12.24 03:33 Marco Filippi wrote:
> We have been using succesfully Hylafax V4.0pl1 on Indy and O2 IRIX
> 6.5.17f.
>
> After upgrading to IRIX 6.5.21f if a receiving FAX was more than 1
> page
> a 2GB file with just the 1st page and some strange stuff were written.
> We tried to move to Origin 200 with the same results.
>
> So we upgraded to SGI Freeware new release, 4.1.2.
>
> With 4.1.2 either on Origin 200 IRIX 6.5.22 or on O2 IRIX 6.5.21f we
> have no way to ither send or receive a fax: as soon as the modem
> completes the dialogue with the fax and starts reading or writing the
> file the programe exits with status 0xa. Last logged line is SEND
> begin
> page (or RECV).
>
> Nov 04 14:40:26.26: [41122]: DIAL 051578337
> Nov 04 14:40:26.26: [41122]: <-- [14:ATDT051578337\r]
> Nov 04 14:40:42.16: [41122]: --> [4:+FCO]
> Nov 04 14:40:44.86: [41122]: --> [27:+FCI:"      +39 051 578337"]
> Nov 04 14:40:44.86: [41122]: REMOTE CSI "+39 051 578337"
> Nov 04 14:40:44.86: [41122]: --> [20:+FIS:1,5,0,2,1,0,0,0]
> Nov 04 14:40:44.86: [41122]: --> [2:OK]
> Nov 04 14:40:44.86: [41122]: REMOTE best rate 14400 bit/s
> Nov 04 14:40:44.86: [41122]: REMOTE max page width 1728 pixels in 215
> mm
>
> Nov 04 14:40:44.86: [41122]: REMOTE max unlimited page length
> Nov 04 14:40:44.86: [41122]: REMOTE best vres 7.7 line/mm
> Nov 04 14:40:44.86: [41122]: REMOTE best format 2-D MR
> Nov 04 14:40:44.86: [41122]: REMOTE best 0 ms/scanline
> Nov 04 14:40:44.86: [41122]: USE 14400 bit/s
> Nov 04 14:40:44.86: [41122]: USE 0 ms/scanline
> Nov 04 14:40:44.87: [41122]: SEND file "docq/doc3.cover;30"
> Nov 04 14:40:44.87: [41122]: USE page width 1728 pixels in 215 mm
> Nov 04 14:40:44.87: [41122]: USE unlimited page length
> Nov 04 14:40:44.87: [41122]: USE 3.85 line/mm
> Nov 04 14:40:44.87: [41122]: USE 1-D MR
> Nov 04 14:40:44.87: [41122]: <-- [23:AT+FIS=0,5,0,2,0,0,0,0\r]
> Nov 04 14:40:45.11: [41122]: --> [2:OK]
> Nov 04 14:40:45.11: [41122]: <-- [7:AT+FDT\r]
> Nov 04 14:40:45.37: [41122]: --> [20:+FCS:0,5,0,2,0,0,0,0]
> Nov 04 14:40:52.47: [41122]: --> [7:CONNECT]
> Nov 04 14:40:52.48: [41122]: SEND begin page
>
> Your facsimile job to 051578337 failed because:
>     Send program terminated abnormally with exit status 0xa
>
> We tuned carefully the package, as using 2D and 14400 let the system
> end
> the job due to a EMPTY LINE from MODEM as a reply to AT+FRH=3 with
> consequent repeated training, as well as using xonxoff on the
> receiving
> side cause the software to end with a T.30 T1 timeout.
>
> We tested Class1 and Class2.0 with the same results (empty line when
> transmitting with a high speed, timeout when receiving at high speed
> xonxoff and exit code 0xa when tuned properly).
>
> Is anyone using Hylavax on SGI?
> Is anyone able to deliver new 4.1.8 binaries for SGI?
>
> I will be really happy to receive such a Xmas present...
>
> My best regards, Marco Filippi - CADMO

Any chance you can file this report on http://bugs.hylafax.org ?

Lee.

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*