Re: [hylafax-users] T.30 Timeout

["Priya" <priya@xxxxxxxxxxx>]

This is Log message.
Can u figure what is the probem ?

##Start

Dec 20 13:44:39.83: [ 2769]: SESSION BEGIN 00001310
Dec 20 13:44:39.83: [ 2769]: HylaFAX (tm) Version 4.1.6
Dec 20 13:44:39.83: [ 2769]: <-- [13:AT+FCLASS=1A\r]
Dec 20 13:44:45.12: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:45.12: [ 2769]: RECV FAX: begin
Dec 20 13:44:45.19: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:45.91: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:48.09: [ 2769]: --> [2:OK]
Dec 20 13:44:48.09: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:44:48.54: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:49.90: [ 2769]: --> [2:OK]
Dec 20 13:44:49.90: [ 2769]: REMOTE TSI ""
Dec 20 13:44:49.90: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:44:49.92: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:50.27: [ 2769]: --> [2:OK]
Dec 20 13:44:50.27: [ 2769]: REMOTE wants 14400 bit/s
Dec 20 13:44:50.27: [ 2769]: REMOTE wants A4 page width (215 mm)
Dec 20 13:44:50.27: [ 2769]: REMOTE wants unlimited page length
Dec 20 13:44:50.27: [ 2769]: REMOTE wants 7.7 line/mm
Dec 20 13:44:50.27: [ 2769]: REMOTE wants 2-D MR
Dec 20 13:44:50.27: [ 2769]: RECV training at v.17 14400 bit/s
Dec 20 13:44:50.27: [ 2769]: <-- [11:AT+FRM=145\r]
Dec 20 13:44:52.10: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:52.96: [ 2769]: RECV: TCF 1553 bytes, 0% non-zero, 1514
zero-run
Dec 20 13:44:52.96: [ 2769]: RECV: reject TCF (zero run too short, min 1800)
Dec 20 13:44:52.97: [ 2769]: --> [10:NO CARRIER]
Dec 20 13:44:52.97: [ 2769]: DELAY 75 ms
Dec 20 13:44:53.05: [ 2769]: <-- [9:AT+FTH=3\r]
Dec 20 13:44:53.25: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:54.43: [ 2769]: --> [2:OK]
Dec 20 13:44:54.43: [ 2769]: TRAINING failed
Dec 20 13:44:54.43: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:44:54.58: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:56.23: [ 2769]: --> [2:OK]
Dec 20 13:44:56.23: [ 2769]: REMOTE TSI ""
Dec 20 13:44:56.23: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:44:56.25: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:56.61: [ 2769]: --> [2:OK]
Dec 20 13:44:56.61: [ 2769]: REMOTE wants 12000 bit/s
Dec 20 13:44:56.61: [ 2769]: REMOTE wants A4 page width (215 mm)
Dec 20 13:44:56.61: [ 2769]: REMOTE wants unlimited page length
Dec 20 13:44:56.61: [ 2769]: REMOTE wants 7.7 line/mm
Dec 20 13:44:56.61: [ 2769]: REMOTE wants 2-D MR
Dec 20 13:44:56.61: [ 2769]: RECV training at v.17 12000 bit/s
Dec 20 13:44:56.61: [ 2769]: <-- [11:AT+FRM=121\r]
Dec 20 13:44:58.43: [ 2769]: --> [7:CONNECT]
Dec 20 13:44:59.99: [ 2769]: RECV: TCF 2343 bytes, 3% non-zero, 2249
zero-run
Dec 20 13:45:00.00: [ 2769]: --> [10:NO CARRIER]
Dec 20 13:45:00.00: [ 2769]: DELAY 75 ms
Dec 20 13:45:00.08: [ 2769]: TRAINING succeeded
Dec 20 13:45:00.08: [ 2769]: <-- [9:AT+FTH=3\r]
Dec 20 13:45:00.28: [ 2769]: --> [7:CONNECT]
Dec 20 13:45:01.46: [ 2769]: --> [2:OK]
Dec 20 13:45:01.46: [ 2769]: <-- [11:AT+FRM=122\r]
Dec 20 13:45:02.03: [ 2769]: --> [7:CONNECT]
Dec 20 13:45:02.03: [ 2769]: RECV: begin page
Dec 20 13:45:12.98: [ 2769]: RECV: 16252 bytes of data, 1092 total lines
Dec 20 13:45:12.98: [ 2769]: RECV: end page
Dec 20 13:45:12.98: [ 2769]: --> [10:NO CARRIER]
Dec 20 13:45:12.98: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:45:16.86: [ 2769]: --> [7:CONNECT]
Dec 20 13:45:16.86: [ 2769]: --> [5:ERROR]
Dec 20 13:45:16.86: [ 2769]: MODEM Command error
Dec 20 13:45:16.86: [ 2769]: FCS error
Dec 20 13:45:16.86: [ 2769]: <-- [9:AT+FRH=3\r]
Dec 20 13:45:16.98: [ 2769]: --> [7:CONNECT]
Dec 20 13:45:22.09: [ 2769]: --> [2:OK]
Dec 20 13:45:22.09: [ 2769]: RECV keeping unconfirmed page
Dec 20 13:45:22.14: [ 2769]: RECV FAX: T.30 T2 timeout, expected page not
received
Dec 20 13:45:22.14: [ 2769]: <-- [9:AT+FTH=3\r]
Dec 20 13:45:22.28: [ 2769]: --> [7:CONNECT]
Dec 20 13:45:23.46: [ 2769]: --> [2:OK] 



##End


On Sat, 20 Dec 2003 19:17:28 +0100, Giulio Orsero wrote
> On Sat, 20 Dec 2003 11:36:37 +0530, "Priya" <priya@xxxxxxxxxxx> wrote:
> 
> >I have installed hylafax - (cvs version got 2 months back) in Linux 7.2.
> >
> >I send and recv faxes successfully, but some times i get the Err T.30 time
> Probably you should send a log with 
> SessionTracing:      0xFFF
> In yout etc/config.<device_id> file
> 
> -- 
> giulioo@xxxxxxxxx
> 
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>   To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*


Regards,
Priya


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*