[hylafax-users] USR5686E Class1 & CallerID Support

[Eric Nichols <eric@xxxxxxxxxx>]

I've been working with Hylafax for about a year now and really have come 
to like it.  I've had to massage a config file for my modem and wanted 
to pass it along in case anyone else has this modem.  Enjoy...
file: config.ttyS0

CountryCode:            1
AreaCode:               302
FAXNumber:              +1-302-555-1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "FAXSERVER"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           100

# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier 
(or not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow 
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow 
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI1
ModemRevQueryCmd:       ATI3            # XXX returns a multi-line result

# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow 
control
Class1SFLOCmd:          ""              # modem does this automatically

# This should resolve "DIS/DTC received 3 times" errors:
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for 
response

# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1

# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
Class2NRCmd:    AT+FNR=1,1,1,0

# Caller ID Setup
#QualifyCID:           etc/cid         # you must create this file
ModemResetCmds:       "AT#CID=1S41=0"
CIDNumber:            "NMBR = "
CIDName:              "NAME="



____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*