 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problem for receive with a Conexant HSC Modem
- To: <hylafax-users@xxxxxxxxxxx>
- Subject: [hylafax-users] Problem for receive with a Conexant HSC Modem
- From: "Eladio Galvez" <eladiogalvez@xxxxxxxxxxx>
- Date: Fri, 31 Oct 2003 10:43:55 +0100
For send the modem works find, but when I try to receive it stablish
connection but not finish the fax operation.
Thanks.
Modem:
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----
Conexant HSC with full driver.
Probemodem:
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----
Serial port that modem is connected to []? ttySHSF0
Now we are going to probe the tty port. This takes a few seconds,
so be patient. Note that if you do not have the modem cabled to
the port, or the modem is turned off, this may hang (just go and
cable up the modem or turn it on, or whatever).
Probing for best speed to talk to modem: 38400 OK.
This looks like a Class 1 and 1.0 modem.
ATI0 RESULT = "OK" RESPONSE = "56000"
ATI1 RESULT = "OK" RESPONSE = "255"
ATI2 RESULT = "OK" RESPONSE = "OK"
ATI3 RESULT = "OK" RESPONSE = "hsfmodem-6.03.00lnxt03091800full"
ATI4 RESULT = "OK" RESPONSE = "Conexant HSF softmodem"
ATI5 RESULT = "OK" RESPONSE = "A0"
ATI6 RESULT = "OK" RESPONSE = "OK"
ATI7 RESULT = "OK" RESPONSE = "255"
ATI8 RESULT = "OK" RESPONSE = "Sep 18 2003 ; 16:51:42"
ATI9 RESULT = "OK" RESPONSE = "SPAIN"
Class 1 stuff...
AT+FCLASS=? RESULT = "OK" RESPONSE = "0,1,1.0"
AT+FCLASS? RESULT = "OK" RESPONSE = "1.0"
AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS? RESULT = "OK" RESPONSE = "1.0"
AT+FJUNK=? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FJUNK? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FAA=? RESULT = "OK" RESPONSE = "0,1"
AT+FAA? RESULT = "OK" RESPONSE = "0"
AT+FAE=? RESULT = "OK" RESPONSE = "0,1"
AT+FAE? RESULT = "OK" RESPONSE = "0"
AT+FTH=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRH=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTM=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRM=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTS=? RESULT = "OK" RESPONSE = "(0-255)"
AT+FRS=? RESULT = "OK" RESPONSE = "(0-255)"
Class 1.0 stuff...
AT+FCLASS=? RESULT = "OK" RESPONSE = "0,1,1.0"
AT+FCLASS? RESULT = "OK" RESPONSE = "1.0"
AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS=1.0 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS? RESULT = "OK" RESPONSE = "1.0"
AT+FJUNK=? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FJUNK? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FAA=? RESULT = "OK" RESPONSE = "0,1"
AT+FAA? RESULT = "OK" RESPONSE = "0"
AT+FAE=? RESULT = "OK" RESPONSE = "0,1"
AT+FAE? RESULT = "OK" RESPONSE = "0"
AT+FTH=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRH=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTM=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRM=? RESULT = "OK" RESPONSE =
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTS=? RESULT = "OK" RESPONSE = "(0-255)"
AT+FRS=? RESULT = "OK" RESPONSE = "(0-255)"
Config: (/var/spool/hylafax/etc/config.ttySHSF0)
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----
CountryCode: 34
AreaCode: 971
FAXNumber: +34000000000
LongDistancePrefix: 00
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 3
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Nothing"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "%%l|%c|Pag. %%P de %%T"
MaxRecvPages: 25
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
ModemDialCmd: ATDT%s # T for tone dialing
Log:
----------------------------------------------------------------------------
----------------------------------------------------------------------------
----
Oct 30 20:07:43.56: [23968]: SESSION BEGIN 00000007 34000000000
Oct 30 20:07:43.56: [23968]: HylaFAX (tm) Version 4.1.7
Oct 30 20:07:43.56: [23968]: <-- [4:ATA\r]
Oct 30 20:07:48.93: [23968]: --> [7:CONNECT]
Oct 30 20:07:48.93: [23968]: ANSWER: FAX CONNECTION DEVICE '/dev/ttySHSF0'
Oct 30 20:07:48.93: [23968]: RECV FAX: begin
Oct 30 20:07:48.93: [23968]: <-- data [23]
Oct 30 20:07:48.93: [23968]: <-- data [2]
Oct 30 20:07:50.41: [23968]: --> [7:CONNECT]
Oct 30 20:07:50.41: [23968]: <-- data [10]
Oct 30 20:07:50.41: [23968]: <-- data [2]
Oct 30 20:07:50.98: [23968]: --> [2:OK]
Oct 30 20:07:50.98: [23968]: <-- [9:AT+FRH=3\r]
Oct 30 20:07:51.14: [23968]: --> [7:CONNECT]
Oct 30 20:07:52.44: [23968]: --> [2:OK]
Oct 30 20:07:52.44: [23968]: REMOTE wants 9600 bit/s
Oct 30 20:07:52.44: [23968]: REMOTE wants page width 1728 pixels in 215 mm
Oct 30 20:07:52.44: [23968]: REMOTE wants unlimited page length
Oct 30 20:07:52.44: [23968]: REMOTE wants 7.7 line/mm
Oct 30 20:07:52.44: [23968]: REMOTE wants 2-D MR
Oct 30 20:07:52.44: [23968]: RECV training at v.29 9600 bit/s
Oct 30 20:07:52.44: [23968]: <-- [10:AT+FRM=96\r]
Oct 30 20:07:52.77: [23968]: --> [7:CONNECT]
Oct 30 20:07:54.27: [23968]: RECV: TCF 1764 bytes, 60% non-zero, 1 zero-run
Oct 30 20:07:54.27: [23968]: RECV: reject TCF (too many non-zero, max 10%)
Oct 30 20:07:54.27: [23968]: RECV: reject TCF (zero run too short, min 1200)
Oct 30 20:07:54.29: [23968]: --> [10:NO CARRIER]
Oct 30 20:07:54.29: [23968]: DELAY 75 ms
Oct 30 20:07:54.37: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:07:54.69: [23968]: --> [7:CONNECT]
Oct 30 20:07:54.69: [23968]: <-- data [3]
Oct 30 20:07:54.69: [23968]: <-- data [2]
Oct 30 20:07:55.99: [23968]: --> [2:OK]
Oct 30 20:07:55.99: [23968]: TRAINING failed
Oct 30 20:07:55.99: [23968]: <-- [9:AT+FRH=3\r]
Oct 30 20:07:56.15: [23968]: --> [7:CONNECT]
Oct 30 20:07:57.45: [23968]: --> [2:OK]
Oct 30 20:07:57.45: [23968]: REMOTE wants 7200 bit/s
Oct 30 20:07:57.45: [23968]: REMOTE wants page width 1728 pixels in 215 mm
Oct 30 20:07:57.45: [23968]: REMOTE wants unlimited page length
Oct 30 20:07:57.45: [23968]: REMOTE wants 7.7 line/mm
Oct 30 20:07:57.45: [23968]: REMOTE wants 2-D MR
Oct 30 20:07:57.45: [23968]: RECV training at v.29 7200 bit/s
Oct 30 20:07:57.45: [23968]: <-- [10:AT+FRM=72\r]
Oct 30 20:07:57.77: [23968]: --> [7:CONNECT]
Oct 30 20:07:59.27: [23968]: RECV: TCF 1320 bytes, 65% non-zero, 1 zero-run
Oct 30 20:07:59.27: [23968]: RECV: reject TCF (too many non-zero, max 10%)
Oct 30 20:07:59.27: [23968]: RECV: reject TCF (zero run too short, min 900)
Oct 30 20:07:59.29: [23968]: --> [10:NO CARRIER]
Oct 30 20:07:59.29: [23968]: DELAY 75 ms
Oct 30 20:07:59.37: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:07:59.69: [23968]: --> [7:CONNECT]
Oct 30 20:07:59.69: [23968]: <-- data [3]
Oct 30 20:07:59.69: [23968]: <-- data [2]
Oct 30 20:08:00.99: [23968]: --> [2:OK]
Oct 30 20:08:00.99: [23968]: TRAINING failed
Oct 30 20:08:00.99: [23968]: <-- [9:AT+FRH=3\r]
Oct 30 20:08:01.15: [23968]: --> [7:CONNECT]
Oct 30 20:08:02.43: [23968]: --> [2:OK]
Oct 30 20:08:02.43: [23968]: REMOTE wants 4800 bit/s
Oct 30 20:08:02.43: [23968]: REMOTE wants page width 1728 pixels in 215 mm
Oct 30 20:08:02.43: [23968]: REMOTE wants unlimited page length
Oct 30 20:08:02.43: [23968]: REMOTE wants 7.7 line/mm
Oct 30 20:08:02.43: [23968]: REMOTE wants 2-D MR
Oct 30 20:08:02.43: [23968]: RECV training at v.27ter 4800 bit/s
Oct 30 20:08:02.43: [23968]: <-- [10:AT+FRM=48\r]
Oct 30 20:08:06.93: [23968]: --> [0:]
Oct 30 20:08:06.93: [23968]: MODEM <Empty line>
Oct 30 20:08:06.93: [23968]: <-- data [1]
Oct 30 20:08:07.13: [23968]: MODEM <Timeout>
Oct 30 20:08:07.13: [23968]: DELAY 75 ms
Oct 30 20:08:07.21: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:08:09.76: [23968]: --> [0:]
Oct 30 20:08:09.76: [23968]: TRAINING failed
Oct 30 20:08:09.76: [23968]: <-- [9:AT+FRH=3\r]
Oct 30 20:08:09.82: [23968]: --> [7:CONNECT]
Oct 30 20:08:14.82: [23968]: <-- data [1]
Oct 30 20:08:14.92: [23968]: --> [2:OK]
Oct 30 20:08:14.92: [23968]: DELAY 1500 ms
Oct 30 20:08:16.42: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:08:16.74: [23968]: --> [2:^P^C]
Oct 30 20:08:16.74: [23968]: DELAY 1500 ms
Oct 30 20:08:18.24: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:08:18.24: [23968]: --> [7:CONNECT]
Oct 30 20:08:18.24: [23968]: <-- data [23]
Oct 30 20:08:18.24: [23968]: <-- data [2]
Oct 30 20:08:19.37: [23968]: --> [2:OK]
Oct 30 20:08:21.24: [23968]: --> [0:]
Oct 30 20:08:21.24: [23968]: MODEM <Empty line>
Oct 30 20:08:21.24: [23968]: DELAY 1500 ms
Oct 30 20:08:22.74: [23968]: <-- [9:AT+FTH=3\r]
Oct 30 20:08:22.78: [23968]: --> [7:CONNECT]
Oct 30 20:08:22.78: [23968]: <-- data [23]
Oct 30 20:08:22.78: [23968]: <-- data [2]
Oct 30 20:08:24.34: [23968]: --> [7:CONNECT]
Oct 30 20:08:24.34: [23968]: <-- data [10]
Oct 30 20:08:24.34: [23968]: <-- data [2]
Oct 30 20:08:24.91: [23968]: --> [2:OK]
Oct 30 20:08:24.91: [23968]: <-- [9:AT+FRH=3\r]
Oct 30 20:08:28.01: [23968]: --> [0:]
Oct 30 20:08:28.01: [23968]: MODEM <Empty line>
Oct 30 20:08:28.01: [23968]: <-- data [1]
Oct 30 20:08:28.21: [23968]: MODEM <Timeout>
Oct 30 20:08:28.21: [23968]: RECV FAX: Failure to train modems
Oct 30 20:08:28.21: [23968]: RECV FAX: end
Oct 30 20:08:28.21: [23968]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
- Prev by Date: [hylafax-users] Hylafax not retrying failed calls
- Next by Date: [hylafax-users] Seeking modem recommendation - multitech
- Previous by thread: [hylafax-users] Problem for receive with a Conexant HSC Modem
- Next by thread: Re: [hylafax-users] Faxgetty and wedged linuxant modems
- Index(es):
Project hosted by iFAX Solutions