Re: [hylafax-users] Hylafax 4.1.3, OSX 10.2.1 (Jaguar), Mac G3 B&W, Internal Modem

[cbain <cbain@acordex.com>]

Bob,

I have gotten Hylafax 4.1.2 to work using the internal modem on Mac OS X 
10.1.5 and 10.2. I configured the modem as an internal modem using class 
2 with the additional changes in the config.cu.modem files as follows:

ModemFlowControl:       rtscts          # was XON/XOFF flow control
ModemSetupDTRCmd:       AT&D3           # setup so DTR drop resets modem
Class2RecvDataTrigger:  "\022"          # character sent to modem to 
start recv
Class2XmitWaitForXON:   no              # if true, wait for XON before 
send


The Class2XmitWaitForXON when set to yes caused the modem to hang when 
sending, the
ModemFlowControl was xonxoff and this caused errors in sending and 
receiving faxes. I am not sure if the other two changes made any 
difference, I just made them base on the differences between the 
RockWell-K56 and the class 2 modem. With these configuration changes I 
can now send and recieve faxes fine with the internal modem.

Chris
 
>Hi,
>
>I compiled and installed the latest HylaFAX on my G3 B&W, which is running
>the latest Mac OSX. Everything went fine (thanks to the on-line HOW-TO and
>list comments!!!) until I sent my first fax. As documented in the list
>archives, there appears to be some time-out problems with the Apple internal
>modem. I set mine up as a Class 2 modem, using /dev/cu.modem.
>
>I'm wondering of any fixes have been found for this configuration. And, more
>generally, I'm wondering if HylaFAX really works with the latest OSX. If so,
>with what configurations? I have an old 28.8 SupraFaxModem--should I be
>using that instead of the internal Apple (Rockwell) modem?
>
>I've attached my log print-out just in case someone's interested and far
>more intelligent than me with finding my actual problem.
>
>Many thanks for any comments!
>
>Bob 
>
>****
>
>Oct 02 01:19:53.55: [  789]: SESSION BEGIN 00000004 13055774370
>Oct 02 01:19:53.55: [  789]: HylaFAX (tm) Version 4.1.3
>Oct 02 01:19:53.55: [  789]: SEND FAX: JOB 2 DEST 1-305-577-4370 COMMID
>00000004 DEVICE '/dev/cu.modem'
>Oct 02 01:19:53.55: [  789]: DELAY 75 ms
>Oct 02 01:19:53.63: [  789]: DELAY 2600 ms
>Oct 02 01:19:57.51: [  789]: <-- [4:ATZ\r]
>Oct 02 01:20:00.67: [  789]: --> [2:OK]
>Oct 02 01:20:00.67: [  789]: DELAY 3000 ms
>Oct 02 01:20:03.67: [  789]: <-- [5:ATE0\r]
>Oct 02 01:20:03.72: [  789]: --> [4:ATE0]
>Oct 02 01:20:03.72: [  789]: --> [2:OK]
>Oct 02 01:20:03.72: [  789]: <-- [5:ATV1\r]
>Oct 02 01:20:03.76: [  789]: --> [2:OK]
>Oct 02 01:20:03.76: [  789]: <-- [5:ATQ0\r]
>Oct 02 01:20:03.81: [  789]: --> [2:OK]
>Oct 02 01:20:03.81: [  789]: <-- [7:ATS0=0\r]
>Oct 02 01:20:03.85: [  789]: --> [2:OK]
>Oct 02 01:20:03.85: [  789]: <-- [7:ATS8=2\r]
>Oct 02 01:20:03.89: [  789]: --> [2:OK]
>Oct 02 01:20:03.90: [  789]: <-- [8:ATS7=60\r]
>Oct 02 01:20:03.95: [  789]: --> [2:OK]
>Oct 02 01:20:03.95: [  789]: <-- [6:AT&K4\r]
>Oct 02 01:20:03.98: [  789]: --> [2:OK]
>Oct 02 01:20:03.98: [  789]: <-- [6:AT&D3\r]
>Oct 02 01:20:04.03: [  789]: --> [2:OK]
>Oct 02 01:20:04.03: [  789]: <-- [6:AT&C1\r]
>Oct 02 01:20:04.07: [  789]: --> [2:OK]
>Oct 02 01:20:04.07: [  789]: <-- [12:AT+FCLASS=2\r]
>Oct 02 01:20:04.12: [  789]: --> [2:OK]
>Oct 02 01:20:04.12: [  789]: <-- [10:AT+FTBC=0\r]
>Oct 02 01:20:04.16: [  789]: --> [2:OK]
>Oct 02 01:20:04.16: [  789]: <-- [10:AT+FBOR=0\r]
>Oct 02 01:20:04.20: [  789]: --> [2:OK]
>Oct 02 01:20:04.20: [  789]: <-- [13:AT+FPHCTO=30\r]
>Oct 02 01:20:04.25: [  789]: --> [2:OK]
>Oct 02 01:20:04.25: [  789]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
>Oct 02 01:20:04.29: [  789]: --> [2:OK]
>Oct 02 01:20:04.29: [  789]: <-- [5:ATM0\r]
>Oct 02 01:20:04.34: [  789]: --> [2:OK]
>Oct 02 01:20:04.36: [  789]: <-- [12:AT+FCLASS=2\r]
>Oct 02 01:20:04.48: [  789]: --> [2:OK]
>Oct 02 01:20:04.48: [  789]: <-- [10:AT+FTBC=0\r]
>Oct 02 01:20:04.63: [  789]: --> [2:OK]
>Oct 02 01:20:04.63: [  789]: <-- [10:AT+FBOR=0\r]
>Oct 02 01:20:04.80: [  789]: --> [2:OK]
>Oct 02 01:20:04.80: [  789]: <-- [13:AT+FPHCTO=30\r]
>Oct 02 01:20:04.95: [  789]: --> [2:OK]
>Oct 02 01:20:04.95: [  789]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
>Oct 02 01:20:05.24: [  789]: --> [2:OK]
>Oct 02 01:20:05.24: [  789]: <-- [18:AT+FLID="HF Shop"\r]
>Oct 02 01:20:05.39: [  789]: --> [2:OK]
>Oct 02 01:20:05.39: [  789]: DIAL 13055774370
>Oct 02 01:20:05.39: [  789]: <-- [16:ATDT13055774370\r]
>Oct 02 01:20:23.28: [  789]: --> [5:+FCON]
>Oct 02 01:20:25.31: [  789]: --> [22:+FDIS: 1,5,0,2,1,0,0,0]
>Oct 02 01:20:25.31: [  789]: --> [2:OK]
>Oct 02 01:20:25.31: [  789]: REMOTE best rate 14400 bit/s
>Oct 02 01:20:25.31: [  789]: REMOTE max page width 1728 pixels in 215 mm
>Oct 02 01:20:25.31: [  789]: REMOTE max unlimited page length
>Oct 02 01:20:25.31: [  789]: REMOTE best vres 7.7 line/mm
>Oct 02 01:20:25.31: [  789]: REMOTE best format 2-D MR
>Oct 02 01:20:25.32: [  789]: REMOTE best 0 ms/scanline
>Oct 02 01:20:25.32: [  789]: USE 14400 bit/s
>Oct 02 01:20:25.32: [  789]: USE 0 ms/scanline
>Oct 02 01:20:25.32: [  789]: SEND file "docq/doc3.ps;31"
>Oct 02 01:20:25.32: [  789]: USE page width 1728 pixels in 215 mm
>Oct 02 01:20:25.32: [  789]: USE unlimited page length
>Oct 02 01:20:25.32: [  789]: USE 7.7 line/mm
>Oct 02 01:20:25.32: [  789]: USE 1-D MR
>Oct 02 01:20:25.32: [  789]: <-- [24:AT+FDIS=1,5,0,2,0,0,0,0\r]
>Oct 02 01:20:25.48: [  789]: --> [2:OK]
>Oct 02 01:20:25.48: [  789]: <-- [7:AT+FDT\r]
>Oct 02 01:20:33.62: [  789]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
>Oct 02 01:20:33.62: [  789]: --> [7:CONNECT]
>Oct 02 01:20:33.62: [  789]: SEND wait for XON
>Oct 02 01:20:43.62: [  789]: <-- [6:AT+FK\r]
>Oct 02 01:21:13.62: [  789]: MODEM <Timeout>
>Oct 02 01:21:13.62: [  789]: SEND: Communication failure during Phase B/C;
>Giving up after 3 attempts to send same page "docq/doc3.ps;31", dirnum 0
>Oct 02 01:21:13.63: [  789]: <-- [5:ATH0\r]
>Oct 02 01:21:13.78: [  789]: --> [9:+FHNG: 50]
>Oct 02 01:21:13.78: [  789]: REMOTE HANGUP: Unspecified Transmit Phase D
>error, including +FPHCTO timeout between data and +FET command (code 50)
>Oct 02 01:21:15.60: [  789]: --> [2:OK]
>Oct 02 01:21:15.85: [  789]: SESSION END
>
>____________________ HylaFAX(tm) Users Mailing List _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
>

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*