Re: [hylafax-users] NO CARRIER does not seem to signal a SEND FAILED

[shachar Goldin <sgoldin@orthospot.com>]

Dirk Lutzebaeck wrote:

>Hi,
>
>this is hylafax 4.1beta3 on Redhat 7.1 using an Eicon ISDN card.
>
>The system sends a fax and the carrier drops after connect. Problem is
>that hylafax thinks the fax is sent but to my understanding it should
>issue a SEND FAILED:
>
>Here is the log:
>Sep 05 10:09:41.74: [  682]: SESSION BEGIN 00021498 4162XXXXXXXXXX
>Sep 05 10:09:41.74: [  682]: SEND FAX: JOB 14869 DEST 004162XXXXXXXXXX COMMID 00021
>498
>Sep 05 10:09:41.74: [  682]: DELAY 2600 ms
>Sep 05 10:09:44.33: [  682]: <-- [4:ATZ\r]
>Sep 05 10:09:44.34: [  682]: --> [2:OK]
>Sep 05 10:09:44.34: [  682]: <-- [32:AT&E7261557S23=2&L*E0V1Q0S0=0H0\r]
>Sep 05 10:09:44.35: [  682]: --> [31:AT&E7261557S23=2&L*E0V1Q0S0=0H0]
>Sep 05 10:09:44.35: [  682]: --> [2:OK]
>Sep 05 10:09:44.35: [  682]: <-- [12:ATS8=2S7=60\r]
>Sep 05 10:09:44.36: [  682]: --> [2:OK]
>Sep 05 10:09:44.36: [  682]: <-- [12:AT+FCLASS=2\r]
>Sep 05 10:09:44.37: [  682]: --> [2:OK]
>Sep 05 10:09:44.37: [  682]: <-- [10:AT+FTBC=0\r]
>Sep 05 10:09:44.38: [  682]: --> [2:OK]
>Sep 05 10:09:44.38: [  682]: <-- [10:AT+FBOR=0\r]
>Sep 05 10:09:44.39: [  682]: --> [2:OK]
>Sep 05 10:09:44.39: [  682]: <-- [13:AT+FPHCTO=30\r]
>Sep 05 10:09:44.40: [  682]: --> [2:OK]
>Sep 05 10:09:44.40: [  682]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
>Sep 05 10:09:44.41: [  682]: --> [2:OK]
>Sep 05 10:09:44.41: [  682]: <-- [5:ATM0\r]
>Sep 05 10:09:44.42: [  682]: --> [2:OK]
>Sep 05 10:09:44.42: [  682]: <-- [12:AT+FCLASS=2\r]
>Sep 05 10:09:44.53: [  682]: --> [2:OK]
>Sep 05 10:09:44.53: [  682]: <-- [10:AT+FTBC=0\r]
>Sep 05 10:09:44.64: [  682]: --> [2:OK]
>Sep 05 10:09:44.64: [  682]: <-- [10:AT+FBOR=0\r]
>Sep 05 10:09:44.75: [  682]: --> [2:OK]
>Sep 05 10:09:44.75: [  682]: <-- [13:AT+FPHCTO=30\r]
>Sep 05 10:09:44.86: [  682]: --> [2:OK]
>Sep 05 10:09:44.86: [  682]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
>Sep 05 10:09:44.97: [  682]: --> [2:OK]
>Sep 05 10:09:44.97: [  682]: <-- [25:AT+FLID="via aeccom.com"\r]
>Sep 05 10:09:45.08: [  682]: --> [2:OK]
>Sep 05 10:09:45.09: [  682]: DIAL 004162XXXXXXXX
>Sep 05 10:09:45.09: [  682]: <-- [18:ATDT004162XXXXXX\r]
>Sep 05 10:10:02.16: [  682]: --> [5:+FCON]
>Sep 05 10:10:02.16: [  682]: --> [28:+FCSI:"       062 832 04 06"]
>Sep 05 10:10:02.16: [  682]: REMOTE CSI "062 832 04 06"
>Sep 05 10:10:02.16: [  682]: --> [21:+FDIS:1,5,0,2,3,1,0,0]
>Sep 05 10:10:02.16: [  682]: --> [21:+FDIS:1,5,0,2,0,1,0,0]
>Sep 05 10:10:02.16: [  682]: --> [2:OK]
>Sep 05 10:10:02.16: [  682]: REMOTE best rate 14400 bit/s
>Sep 05 10:10:02.16: [  682]: REMOTE max page width 1728 pixels in 215 mm
>Sep 05 10:10:02.16: [  682]: REMOTE max unlimited page length
>Sep 05 10:10:02.16: [  682]: REMOTE best vres 7.7 line/mm
>Sep 05 10:10:02.16: [  682]: REMOTE best format 1-D MR
>Sep 05 10:10:02.16: [  682]: REMOTE supports T.30 Annex A, ECM
>Sep 05 10:10:02.16: [  682]: REMOTE best 0 ms/scanline
>Sep 05 10:10:02.16: [  682]: USE 14400 bit/s
>Sep 05 10:10:02.16: [  682]: USE 0 ms/scanline
>Sep 05 10:10:02.16: [  682]: USE error correction mode
>Sep 05 10:10:02.16: [  682]: <-- [5:ATH0\r]
>Sep 05 10:10:02.27: [  682]: --> [10:NO CARRIER]
>Sep 05 10:10:02.27: [  682]: MODEM No carrier
>Sep 05 10:10:02.27: [  682]: SESSION END
>
>
>
>After that I got a completion mail:
>
>Your facsimile job to 004162XXXXXXXXX was completed successfully.
>
>         Pages: 0
>       Quality: Fine
>    Page Width: 209 (mm)
>   Page Length: 296 (mm)
>   Signal Rate: 14400 bit/s
>   Data Format: 2-D MMR
>Submitted From: toro.aeccom.int
>         JobID: 14869
>       GroupID: 14869
>        CommID: c00021498
>
>Processing time was 0:26.
>
>
>Any suggestions?
>
>Dirk
>
>____________________ HylaFAX(tm) Users Mailing List _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
>
>  
>
check for further logs...
it might have gone through on a second or third or forth try
cd log/
grep 14869 *

good luck
Shachar Goldin
Director of IT
Orthospot, inc.




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*