[hylafax-users] Problems when receiving (sending is ok)

["Gunther Wenzel Cyster" <gwenzel@costarricense.cr>]

Hello everybody,

I�m running hylafax 4.1 on Slackware 8 (kernel 2.2.19), modem is Class 2 Rockwell RC32ACL-based.
I did not compile the package, instead I downloaded the binary available from hylafax.org.

Whenever I receive a fax, first page comes through but then the process stalls (until I abort it) and the modem stays in state "Receiving from ...".

Here is one such log (from intercontinental fax):

Jun 25 05:14:21.27: [  177]: SESSION BEGIN 00000039 5062235001
Jun 25 05:14:21.27: [  177]: <-- [4:ATA\r]
Jun 25 05:14:24.83: [  177]: --> [3:FAX]
Jun 25 05:14:31.23: [  177]: --> [5:+FCON]
Jun 25 05:14:31.23: [  177]: ANSWER: FAX CONNECTION
Jun 25 05:14:31.23: [  177]: RECV FAX: begin
Jun 25 05:14:32.88: [  177]: --> [29:+FTSI: "     +49 2191 967946"]
Jun 25 05:14:32.88: [  177]: REMOTE TSI "+49 2191 967946"
Jun 25 05:14:33.17: [  177]: --> [22:+FDCS: 0,3,0,2,1,0,0,3]
Jun 25 05:14:33.17: [  177]: REMOTE wants 9600 bit/s
Jun 25 05:14:33.17: [  177]: REMOTE wants page width 1728 pixels in 215 mm
Jun 25 05:14:33.17: [  177]: REMOTE wants unlimited page length 
Jun 25 05:14:33.17: [  177]: REMOTE wants 3.85 line/mm
Jun 25 05:14:33.17: [  177]: REMOTE wants 2-D MR
Jun 25 05:14:33.28: [  177]: --> [2:OK]
Jun 25 05:14:33.28: [  177]: <-- [7:AT+FDR\r]
Jun 25 05:14:34.89: [  177]: --> [5:+FCFR]
Jun 25 05:14:37.83: [  177]: --> [22:+FDCS: 0,3,0,2,1,0,0,3]
Jun 25 05:14:37.83: [  177]: REMOTE wants 9600 bit/s
Jun 25 05:14:37.83: [  177]: REMOTE wants page width 1728 pixels in 215 mm
Jun 25 05:14:37.83: [  177]: REMOTE wants unlimited page length 
Jun 25 05:14:37.83: [  177]: REMOTE wants 3.85 line/mm
Jun 25 05:14:37.83: [  177]: REMOTE wants 2-D MR
Jun 25 05:14:37.83: [  177]: --> [7:CONNECT]
Jun 25 05:14:37.83: [  177]: RECV: begin page
Jun 25 05:14:37.83: [  177]: RECV: send trigger 022
Jun 25 05:14:37.83: [  177]: <-- data [1]
Jun 25 05:14:56.27: [  177]: RECV: 1149 total lines, 0 bad lines, 0 consecutive bad lines
Jun 25 05:14:56.27: [  177]: --> [17:+FPTS: 1,2219,0,0]
Jun 25 05:14:57.51: [  177]: --> [7:+FET: 2]
Jun 25 05:14:57.51: [  177]: RECV recv EOP (no more pages or documents)
Jun 25 05:14:57.62: [  177]: --> [2:OK]

------> Here it stalls, notice time until I realized and intervened with faxstate.

Jun 25 10:57:25.97: [  177]: STATE "R"
Jun 25 11:42:38.59: [  177]: STATE "R"
Jun 25 18:14:08.94: [  177]: CLOSE /dev/ttyS2


This other one is similar (from local fax):

Jun 26 11:44:33.29: [ 1304]: SESSION BEGIN 00000044 5062235001
Jun 26 11:44:33.29: [ 1304]: <-- [4:ATA\r]
Jun 26 11:44:45.00: [ 1304]: --> [3:FAX]
Jun 26 11:44:51.07: [ 1304]: --> [5:+FCON]
Jun 26 11:44:51.07: [ 1304]: ANSWER: FAX CONNECTION
Jun 26 11:44:51.07: [ 1304]: RECV FAX: begin
Jun 26 11:44:52.70: [ 1304]: --> [29:+FTSI: "         506 2220278"]
Jun 26 11:44:52.70: [ 1304]: REMOTE TSI "506 2220278"
Jun 26 11:44:53.01: [ 1304]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 9600 bit/s
Jun 26 11:44:53.01: [ 1304]: REMOTE wants page width 1728 pixels in 215 mm
Jun 26 11:44:53.01: [ 1304]: REMOTE wants unlimited page length 
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 3.85 line/mm
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 1-D MR
Jun 26 11:44:53.12: [ 1304]: --> [2:OK]
Jun 26 11:44:53.12: [ 1304]: <-- [7:AT+FDR\r]
Jun 26 11:44:54.75: [ 1304]: --> [5:+FCFR]
Jun 26 11:44:58.30: [ 1304]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 9600 bit/s
Jun 26 11:44:58.30: [ 1304]: REMOTE wants page width 1728 pixels in 215 mm
Jun 26 11:44:58.30: [ 1304]: REMOTE wants unlimited page length 
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 3.85 line/mm
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 1-D MR
Jun 26 11:44:58.30: [ 1304]: --> [7:CONNECT]
Jun 26 11:44:58.30: [ 1304]: RECV: begin page
Jun 26 11:44:58.30: [ 1304]: RECV: send trigger 022
Jun 26 11:44:58.30: [ 1304]: <-- data [1]
Jun 26 11:45:37.94: [ 1304]: RECV: 1163 total lines, 1 bad lines, 1 consecutive bad lines
Jun 26 11:45:37.94: [ 1304]: --> [17:+FPTS: 1,2219,0,0]
Jun 26 11:45:39.32: [ 1304]: --> [7:+FET: 0]
Jun 26 11:45:39.32: [ 1304]: RECV recv MPS (more pages, same document)
Jun 26 11:45:39.32: [ 1304]: --> [2:OK]

--------> Here I was monitoring so reacted sooner (this time properly with faxabort)

Jun 26 11:47:07.21: [ 1304]: ABORT: job abort requested
Jun 26 11:47:07.22: [ 1304]: RECV FAX (00000044): recvq/fax00012.tif from 506 2220278, route to <unspecified>, 0 pages in 2:16
Jun 26 11:47:07.22: [ 1304]: RECV FAX: Receive aborted due to operator intervention
Jun 26 11:47:07.22: [ 1304]: <-- [6:AT+FK\r]
Jun 26 11:47:07.31: [ 1304]: --> [10:+FHNG: 100]
Jun 26 11:47:07.31: [ 1304]: REMOTE HANGUP: Unspecified Phase D error (code 100)
Jun 26 11:47:07.31: [ 1304]: --> [2:OK]
Jun 26 11:47:07.31: [ 1304]: RECV FAX (00000044): session with 506 2220278 terminated abnormally: Receive aborted due to operator intervention
Jun 26 11:47:07.31: [ 1304]: RECV FAX: bin/faxrcvd "recvq/fax00012.tif" "ttyS2" "00000044" "Receive aborted due to operator intervention"
Jun 26 11:47:07.62: [ 1304]: RECV FAX: end
Jun 26 11:47:07.62: [ 1304]: SESSION END

Any help will be greatly appreciated.

Regards,

Gunther Wenzel


Saludos,

Gunther Wenzel


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null