[hylafax-users] Hylafax & AccelePort RAS 8

["Alex S. Pereira" <aspereira@ig.com.br>]

Hi,

I have a server with Red Hat 7.2 and Hylafax 4.1.1, I am testing a
multimodem card from DIGI called AccelePort RAS 8, I guess that is a good
card, the percentual of failure that was 40% with USRobotics modem, now is
4,8% with this multimodem card, I am just having one problem, some incoming
faxes miss some horizontal lines, the transmission is OK but the printed
faxes miss some horizontal lines, in some case the first page is OK and the
others is wrong, my config is :

#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 55
AreaCode: 11
FAXNumber: 5509-0382
LongDistancePrefix: 21
InternationalPrefix: 21
DialStringRules: etc/dialrules
ServerTracing: 127
SessionTracing: 127
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: Continental
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
PercentGoodLines: 5
MaxConsecutiveBadLines: 10
MaxRecvPages: 100
FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd02
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
#ModemRate: 19200 # max rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command

This is the transmission log :

Mar 28 13:26:53.19: [19480]: SESSION BEGIN 00000388 551155090377
Mar 28 13:26:53.19: [19480]: HylaFAX (tm) Version 4.1.1
Mar 28 13:26:53.19: [19480]: <-- [4:ATA\r]
Mar 28 13:26:59.05: [19480]: --> [74:+FHT: FF 03 40 20 20 20 20 20 20 20 20
20 6C 61 74 6E 65 6E 69 74 6E 6F 43]
Mar 28 13:26:59.33: [19480]: --> [26:+FHT: FF 13 80 00 EE FA 46]
Mar 28 13:27:04.31: [19480]: --> [74:+FHT: FF 03 40 20 20 20 20 20 20 20 20
20 6C 61 74 6E 65 6E 69 74 6E 6F 43]
Mar 28 13:27:04.59: [19480]: --> [26:+FHT: FF 13 80 00 EE FA 46]
Mar 28 13:27:05.45: [19480]: --> [4:+FCO]
Mar 28 13:27:05.45: [19480]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyG0_00'
Mar 28 13:27:05.45: [19480]: MODEM input buffering enabled
Mar 28 13:27:05.45: [19480]: RECV FAX: begin
Mar 28 13:27:07.04: [19480]: --> [74:+FHR: FF 03 43 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20]
Mar 28 13:27:07.39: [19480]: --> [26:+FHR: FF 13 83 00 86 88 00]
Mar 28 13:27:07.39: [19480]: --> [27:+FTI:" "]
Mar 28 13:27:07.39: [19480]: REMOTE TSI ""
Mar 28 13:27:07.39: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:27:07.39: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:27:07.39: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:27:07.39: [19480]: REMOTE wants unlimited page length
Mar 28 13:27:07.39: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:27:07.39: [19480]: REMOTE wants 2-D MR
Mar 28 13:27:07.39: [19480]: --> [2:OK]
Mar 28 13:27:07.39: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:27:10.75: [19480]: --> [14:+FHT: FF 13 84]
Mar 28 13:27:11.89: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:27:11.89: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:27:11.89: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:27:11.89: [19480]: REMOTE wants unlimited page length
Mar 28 13:27:11.89: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:27:11.89: [19480]: REMOTE wants 2-D MR
Mar 28 13:27:11.89: [19480]: --> [7:CONNECT]
Mar 28 13:27:11.89: [19480]: RECV: begin page
Mar 28 13:27:11.89: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:27:11.92: [19480]: RECV: send trigger 022
Mar 28 13:27:11.92: [19480]: <-- data [1]
Mar 28 13:27:48.87: [19480]: RECV: 25233 bytes of data, 929 total lines
Mar 28 13:27:48.87: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:27:50.15: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:27:50.15: [19480]: --> [16:+FPS:1,929,1,0,0]
Mar 28 13:27:50.15: [19480]: --> [6:+FET:0]
Mar 28 13:27:50.15: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:27:50.15: [19480]: --> [2:OK]
Mar 28 13:27:50.15: [19480]: RECV send MCF (message confirmation)
Mar 28 13:27:50.15: [19480]: RECV FAX (00000388): from , page 1 in 0:43,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:27:50.15: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:27:51.66: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:27:52.77: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:27:52.77: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:27:52.77: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:27:52.77: [19480]: REMOTE wants unlimited page length
Mar 28 13:27:52.77: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:27:52.77: [19480]: REMOTE wants 2-D MR
Mar 28 13:27:52.77: [19480]: --> [7:CONNECT]
Mar 28 13:27:52.77: [19480]: RECV: begin page
Mar 28 13:27:52.77: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:27:52.79: [19480]: RECV: send trigger 022
Mar 28 13:27:52.79: [19480]: <-- data [1]
Mar 28 13:28:33.38: [19480]: RECV: 25468 bytes of data, 1159 total lines
Mar 28 13:28:33.38: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:28:34.69: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:28:34.69: [19480]: --> [17:+FPS:1,1160,1,0,0]
Mar 28 13:28:34.69: [19480]: --> [6:+FET:0]
Mar 28 13:28:34.69: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:28:34.69: [19480]: --> [2:OK]
Mar 28 13:28:34.69: [19480]: RECV send MCF (message confirmation)
Mar 28 13:28:34.69: [19480]: RECV FAX (00000388): from , page 2 in 0:44,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:28:34.69: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:28:36.19: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:28:37.32: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:28:37.32: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:28:37.32: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:28:37.32: [19480]: REMOTE wants unlimited page length
Mar 28 13:28:37.32: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:28:37.32: [19480]: REMOTE wants 2-D MR
Mar 28 13:28:37.32: [19480]: --> [7:CONNECT]
Mar 28 13:28:37.32: [19480]: RECV: begin page
Mar 28 13:28:37.32: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:28:37.34: [19480]: RECV: send trigger 022
Mar 28 13:28:37.34: [19480]: <-- data [1]
Mar 28 13:29:09.23: [19480]: RECV: 16503 bytes of data, 1143 total lines
Mar 28 13:29:09.23: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:29:10.54: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:29:10.54: [19480]: --> [17:+FPS:1,1144,1,0,0]
Mar 28 13:29:10.54: [19480]: --> [6:+FET:0]
Mar 28 13:29:10.54: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:29:10.54: [19480]: --> [2:OK]
Mar 28 13:29:10.54: [19480]: RECV send MCF (message confirmation)
Mar 28 13:29:10.54: [19480]: RECV FAX (00000388): from , page 3 in 0:36,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:29:10.54: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:29:12.05: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:29:13.18: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:29:13.18: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:29:13.18: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:29:13.18: [19480]: REMOTE wants unlimited page length
Mar 28 13:29:13.18: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:29:13.18: [19480]: REMOTE wants 2-D MR
Mar 28 13:29:13.18: [19480]: --> [7:CONNECT]
Mar 28 13:29:13.18: [19480]: RECV: begin page
Mar 28 13:29:13.18: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:29:13.20: [19480]: RECV: send trigger 022
Mar 28 13:29:13.20: [19480]: <-- data [1]
Mar 28 13:29:45.56: [19480]: RECV: 17262 bytes of data, 1201 total lines
Mar 28 13:29:45.56: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:29:46.87: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:29:46.87: [19480]: --> [17:+FPS:1,1201,1,0,0]
Mar 28 13:29:46.87: [19480]: --> [6:+FET:0]
Mar 28 13:29:46.87: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:29:46.87: [19480]: --> [2:OK]
Mar 28 13:29:46.87: [19480]: RECV send MCF (message confirmation)
Mar 28 13:29:46.87: [19480]: RECV FAX (00000388): from , page 4 in 0:36,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:29:46.87: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:29:48.38: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:29:49.48: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:29:49.48: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:29:49.48: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:29:49.48: [19480]: REMOTE wants unlimited page length
Mar 28 13:29:49.48: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:29:49.48: [19480]: REMOTE wants 2-D MR
Mar 28 13:29:49.48: [19480]: --> [7:CONNECT]
Mar 28 13:29:49.48: [19480]: RECV: begin page
Mar 28 13:29:49.48: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:29:49.50: [19480]: RECV: send trigger 022
Mar 28 13:29:49.50: [19480]: <-- data [1]
Mar 28 13:30:23.49: [19480]: RECV: 17839 bytes of data, 1153 total lines
Mar 28 13:30:23.49: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:30:24.79: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:30:24.79: [19480]: --> [17:+FPS:1,1153,1,0,0]
Mar 28 13:30:24.79: [19480]: --> [6:+FET:0]
Mar 28 13:30:24.79: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:30:24.79: [19480]: --> [2:OK]
Mar 28 13:30:24.79: [19480]: RECV send MCF (message confirmation)
Mar 28 13:30:24.79: [19480]: RECV FAX (00000388): from , page 5 in 0:38,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:30:24.79: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:30:26.30: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:30:27.41: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:30:27.41: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:30:27.41: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:30:27.41: [19480]: REMOTE wants unlimited page length
Mar 28 13:30:27.41: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:30:27.41: [19480]: REMOTE wants 2-D MR
Mar 28 13:30:27.41: [19480]: --> [7:CONNECT]
Mar 28 13:30:27.41: [19480]: RECV: begin page
Mar 28 13:30:27.41: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:30:27.43: [19480]: RECV: send trigger 022
Mar 28 13:30:27.43: [19480]: <-- data [1]
Mar 28 13:31:02.96: [19480]: RECV: 23106 bytes of data, 967 total lines
Mar 28 13:31:02.96: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:31:04.27: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:31:04.27: [19480]: --> [16:+FPS:1,968,1,0,0]
Mar 28 13:31:04.27: [19480]: --> [6:+FET:0]
Mar 28 13:31:04.27: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:31:04.27: [19480]: --> [2:OK]
Mar 28 13:31:04.27: [19480]: RECV send MCF (message confirmation)
Mar 28 13:31:04.27: [19480]: RECV FAX (00000388): from , page 6 in 0:40,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:31:04.27: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:31:05.78: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:31:06.88: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:31:06.88: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:31:06.88: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:31:06.88: [19480]: REMOTE wants unlimited page length
Mar 28 13:31:06.88: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:31:06.88: [19480]: REMOTE wants 2-D MR
Mar 28 13:31:06.88: [19480]: --> [7:CONNECT]
Mar 28 13:31:06.88: [19480]: RECV: begin page
Mar 28 13:31:06.88: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:31:06.91: [19480]: RECV: send trigger 022
Mar 28 13:31:06.91: [19480]: <-- data [1]
Mar 28 13:31:43.52: [19480]: RECV: 22199 bytes of data, 1165 total lines
Mar 28 13:31:43.52: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:31:44.83: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:31:44.83: [19480]: --> [17:+FPS:1,1166,1,0,0]
Mar 28 13:31:44.83: [19480]: --> [6:+FET:0]
Mar 28 13:31:44.83: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:31:44.83: [19480]: --> [2:OK]
Mar 28 13:31:44.83: [19480]: RECV send MCF (message confirmation)
Mar 28 13:31:44.83: [19480]: RECV FAX (00000388): from , page 7 in 0:40,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:31:44.83: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:31:46.34: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:31:47.45: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:31:47.45: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:31:47.45: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:31:47.45: [19480]: REMOTE wants unlimited page length
Mar 28 13:31:47.45: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:31:47.45: [19480]: REMOTE wants 2-D MR
Mar 28 13:31:47.45: [19480]: --> [7:CONNECT]
Mar 28 13:31:47.45: [19480]: RECV: begin page
Mar 28 13:31:47.45: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:31:47.47: [19480]: RECV: send trigger 022
Mar 28 13:31:47.47: [19480]: <-- data [1]
Mar 28 13:32:19.62: [19480]: RECV: 20695 bytes of data, 1151 total lines
Mar 28 13:32:19.62: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:32:20.91: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:32:20.91: [19480]: --> [17:+FPS:1,1151,1,0,0]
Mar 28 13:32:20.91: [19480]: --> [6:+FET:0]
Mar 28 13:32:20.91: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:32:20.91: [19480]: --> [2:OK]
Mar 28 13:32:20.91: [19480]: RECV send MCF (message confirmation)
Mar 28 13:32:20.91: [19480]: RECV FAX (00000388): from , page 8 in 0:36,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:32:20.91: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:32:22.42: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:32:23.52: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:32:23.52: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:32:23.52: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:32:23.52: [19480]: REMOTE wants unlimited page length
Mar 28 13:32:23.52: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:32:23.52: [19480]: REMOTE wants 2-D MR
Mar 28 13:32:23.52: [19480]: --> [7:CONNECT]
Mar 28 13:32:23.52: [19480]: RECV: begin page
Mar 28 13:32:23.52: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:32:23.54: [19480]: RECV: send trigger 022
Mar 28 13:32:23.54: [19480]: <-- data [1]
Mar 28 13:32:54.41: [19480]: RECV: 19807 bytes of data, 1153 total lines
Mar 28 13:32:54.41: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:32:55.72: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:32:55.72: [19480]: --> [17:+FPS:1,1153,1,0,0]
Mar 28 13:32:55.72: [19480]: --> [6:+FET:0]
Mar 28 13:32:55.72: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:32:55.72: [19480]: --> [2:OK]
Mar 28 13:32:55.72: [19480]: RECV send MCF (message confirmation)
Mar 28 13:32:55.72: [19480]: RECV FAX (00000388): from , page 9 in 0:35,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:32:55.72: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:32:57.23: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:32:58.35: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:32:58.35: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:32:58.35: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:32:58.35: [19480]: REMOTE wants unlimited page length
Mar 28 13:32:58.35: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:32:58.35: [19480]: REMOTE wants 2-D MR
Mar 28 13:32:58.35: [19480]: --> [7:CONNECT]
Mar 28 13:32:58.35: [19480]: RECV: begin page
Mar 28 13:32:58.35: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:32:58.37: [19480]: RECV: send trigger 022
Mar 28 13:32:58.37: [19480]: <-- data [1]
Mar 28 13:33:29.13: [19480]: RECV: 19712 bytes of data, 1161 total lines
Mar 28 13:33:29.13: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:33:30.43: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:33:30.43: [19480]: --> [17:+FPS:1,1161,1,0,0]
Mar 28 13:33:30.43: [19480]: --> [6:+FET:0]
Mar 28 13:33:30.43: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:33:30.43: [19480]: --> [2:OK]
Mar 28 13:33:30.43: [19480]: RECV send MCF (message confirmation)
Mar 28 13:33:30.43: [19480]: RECV FAX (00000388): from , page 10 in 0:35,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:33:30.43: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:33:31.94: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:33:33.07: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:33:33.07: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:33:33.07: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:33:33.07: [19480]: REMOTE wants unlimited page length
Mar 28 13:33:33.07: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:33:33.07: [19480]: REMOTE wants 2-D MR
Mar 28 13:33:33.07: [19480]: --> [7:CONNECT]
Mar 28 13:33:33.07: [19480]: RECV: begin page
Mar 28 13:33:33.07: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:33:33.09: [19480]: RECV: send trigger 022
Mar 28 13:33:33.09: [19480]: <-- data [1]
Mar 28 13:34:04.75: [19480]: RECV: 19696 bytes of data, 1153 total lines
Mar 28 13:34:04.75: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:34:06.03: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:34:06.03: [19480]: --> [17:+FPS:1,1154,1,0,0]
Mar 28 13:34:06.03: [19480]: --> [6:+FET:0]
Mar 28 13:34:06.03: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:34:06.03: [19480]: --> [2:OK]
Mar 28 13:34:06.03: [19480]: RECV send MCF (message confirmation)
Mar 28 13:34:06.03: [19480]: RECV FAX (00000388): from , page 11 in 0:36,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:34:06.03: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:34:07.54: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:34:08.65: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:34:08.65: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:34:08.65: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:34:08.65: [19480]: REMOTE wants unlimited page length
Mar 28 13:34:08.65: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:34:08.65: [19480]: REMOTE wants 2-D MR
Mar 28 13:34:08.65: [19480]: --> [7:CONNECT]
Mar 28 13:34:08.65: [19480]: RECV: begin page
Mar 28 13:34:08.65: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:34:08.67: [19480]: RECV: send trigger 022
Mar 28 13:34:08.67: [19480]: <-- data [1]
Mar 28 13:34:39.40: [19480]: RECV: 19739 bytes of data, 1163 total lines
Mar 28 13:34:39.40: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:34:40.71: [19480]: --> [14:+FHR: FF 13 4F]
Mar 28 13:34:40.71: [19480]: --> [17:+FPS:1,1163,1,0,0]
Mar 28 13:34:40.71: [19480]: --> [6:+FET:0]
Mar 28 13:34:40.71: [19480]: RECV recv MPS (more pages, same document)
Mar 28 13:34:40.71: [19480]: --> [2:OK]
Mar 28 13:34:40.71: [19480]: RECV send MCF (message confirmation)
Mar 28 13:34:40.71: [19480]: RECV FAX (00000388): from , page 12 in 0:34,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:34:40.71: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:34:42.22: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:34:43.32: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]
Mar 28 13:34:43.32: [19480]: REMOTE wants 9600 bit/s
Mar 28 13:34:43.32: [19480]: REMOTE wants page width 1728 pixels in 215 mm
Mar 28 13:34:43.32: [19480]: REMOTE wants unlimited page length
Mar 28 13:34:43.32: [19480]: REMOTE wants 3.85 line/mm
Mar 28 13:34:43.32: [19480]: REMOTE wants 2-D MR
Mar 28 13:34:43.32: [19480]: --> [7:CONNECT]
Mar 28 13:34:43.32: [19480]: RECV: begin page
Mar 28 13:34:43.32: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Mar 28 13:34:43.34: [19480]: RECV: send trigger 022
Mar 28 13:34:43.34: [19480]: <-- data [1]
Mar 28 13:35:17.31: [19480]: RECV: 18201 bytes of data, 1155 total lines
Mar 28 13:35:17.31: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Mar 28 13:35:18.61: [19480]: --> [14:+FHR: FF 13 2F]
Mar 28 13:35:18.61: [19480]: --> [17:+FPS:1,1155,1,0,0]
Mar 28 13:35:18.61: [19480]: --> [6:+FET:2]
Mar 28 13:35:18.61: [19480]: RECV recv EOP (no more pages or documents)
Mar 28 13:35:18.61: [19480]: --> [2:OK]
Mar 28 13:35:18.61: [19480]: RECV send MCF (message confirmation)
Mar 28 13:35:18.61: [19480]: RECV FAX (00000388): from , page 13 in 0:38,
INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Mar 28 13:35:18.61: [19480]: RECV FAX (00000388): recvq/fax00364.tif from ,
route to <unspecified>, 13 pages in 8:13
Mar 28 13:35:18.61: [19480]: <-- [7:AT+FDR\r]
Mar 28 13:35:20.12: [19480]: --> [14:+FHT: FF 13 8C]
Mar 28 13:35:20.12: [19480]: RECV FAX: /var/spool/hylafax/bin/faxrcvd01
"recvq/fax00364.tif" "ttyG0_00" "00000388" "" "" ""
Mar 28 13:35:23.74: [19480]: RECV FAX: end
Mar 28 13:35:23.74: [19480]: SESSION END


Like you can see, don't have error, but the all pages miss the horizontal
lines, someone can help me ?


Thanks,

Alex




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null