 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Incoming Faxes are being scrambled
- To: <hylafax-users@hylafax.org>
- Subject: [hylafax-users] Incoming Faxes are being scrambled
- From: "Dennis Fellows" <dennis@lamtop.com>
- Date: Thu, 5 Apr 2001 13:01:40 -0500
I sent a question yesterday but I was not subscribing to this list. So I am resending this question but I also have some followup info. I am running RH7.0, Hyla-Fax 4.1beta2 (binary hylafax-4.1beta2-2rh7.i386.rpm), libtiff 3.4 (developer beta037-4), Multitech 2834ZDX modems (four of 'em), and a RocketPort multi-I/O card. I have had problems receiving faxes with this set up from certain senders. When I receive thier transmission all I get is a garbled tiff that is usually just an inch or more of legible text and then the rest is black lines and speckles. The sender would get a successful transmission reprot from his fax machine. When I have the sender send the fax to a standalone fax machine (Richoh), the fax will be successful. When I send from my Richoh to my HylaFax server it has no problems. I was very puzzled because the log reported no errors (see below). Apr 04 09:24:44.78: [ 4447]: SESSION BEGIN 00000005 12626584184 Apr 04 09:24:44.78: [ 4447]: <-- [4:ATA\r] Apr 04 09:24:54.69: [ 4447]: --> [5:+FCON] Apr 04 09:24:54.69: [ 4447]: ANSWER: FAX CONNECTION Apr 04 09:24:54.69: [ 4447]: RECV FAX: begin Apr 04 09:24:59.93: [ 4447]: --> [28:+FTSI:" 6082407266"] Apr 04 09:24:59.93: [ 4447]: REMOTE TSI "6082407266" Apr 04 09:24:59.93: [ 4447]: --> [21:+FDCS:0,5,0,2,1,0,0,3] Apr 04 09:24:59.93: [ 4447]: REMOTE wants 14400 bit/s Apr 04 09:24:59.93: [ 4447]: REMOTE wants page width 1728 pixels in 215 mm Apr 04 09:24:59.93: [ 4447]: REMOTE wants unlimited page length Apr 04 09:24:59.93: [ 4447]: REMOTE wants 3.85 line/mm Apr 04 09:24:59.93: [ 4447]: REMOTE wants 2-D MR Apr 04 09:24:59.93: [ 4447]: --> [2:OK] Apr 04 09:24:59.93: [ 4447]: <-- [7:AT+FDR\r] Apr 04 09:25:01.35: [ 4447]: --> [5:+FCFR] Apr 04 09:25:01.35: [ 4447]: --> [28:+FTSI:" 6082407266"] Apr 04 09:25:01.35: [ 4447]: REMOTE TSI "6082407266" Apr 04 09:25:01.35: [ 4447]: --> [21:+FDCS:0,5,0,2,1,0,0,3] Apr 04 09:25:01.35: [ 4447]: REMOTE wants 14400 bit/s Apr 04 09:25:01.35: [ 4447]: REMOTE wants page width 1728 pixels in 215 mm Apr 04 09:25:01.35: [ 4447]: REMOTE wants unlimited page length Apr 04 09:25:01.35: [ 4447]: REMOTE wants unlimited page length Apr 04 09:25:01.35: [ 4447]: REMOTE wants 3.85 line/mm Apr 04 09:25:01.35: [ 4447]: REMOTE wants 2-D MR Apr 04 09:25:02.86: [ 4447]: --> [7:CONNECT] Apr 04 09:25:02.86: [ 4447]: RECV: begin page Apr 04 09:25:02.86: [ 4447]: RECV: send trigger 022 Apr 04 09:25:02.86: [ 4447]: <-- data [1] Apr 04 09:25:18.08: [ 4447]: RECV: 25322 bytes of data, 261 total lines Apr 04 09:25:18.19: [ 4447]: --> [15:+FPTS:1,0,0,0,0] Apr 04 09:25:19.48: [ 4447]: --> [6:+FET:2] Apr 04 09:25:19.48: [ 4447]: RECV recv EOP (no more pages or documents) Apr 04 09:25:19.48: [ 4447]: --> [2:OK] Apr 04 09:25:19.48: [ 4447]: RECV send MCF (message confirmation) Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): from 6082407266, page 1 in 0:2 0, INF, 3.85 line/mm, 2-D MR, 14400 bit/s Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): recvq/fax00005.tif from 608240 7266, route to <unspecified>, 1 pages in 0:25 Apr 04 09:25:19.48: [ 4447]: <-- [7:AT+FDR\r] Apr 04 09:25:22.53: [ 4447]: --> [7:+FHNG:0] Apr 04 09:25:22.53: [ 4447]: REMOTE HANGUP: Normal and proper end of connection (code 0) Apr 04 09:25:22.53: [ 4447]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif" "ttyR1" "00000005" "" Apr 04 09:25:01.35: [ 4447]: REMOTE wants 2-D MR Apr 04 09:25:02.86: [ 4447]: --> [7:CONNECT] Apr 04 09:25:02.86: [ 4447]: RECV: begin page Apr 04 09:25:02.86: [ 4447]: RECV: send trigger 022 Apr 04 09:25:02.86: [ 4447]: <-- data [1] Apr 04 09:25:18.08: [ 4447]: RECV: 25322 bytes of data, 261 total lines Apr 04 09:25:18.19: [ 4447]: --> [15:+FPTS:1,0,0,0,0] Apr 04 09:25:19.48: [ 4447]: --> [6:+FET:2] Apr 04 09:25:19.48: [ 4447]: RECV recv EOP (no more pages or documents) Apr 04 09:25:19.48: [ 4447]: --> [2:OK] Apr 04 09:25:19.48: [ 4447]: RECV send MCF (message confirmation) Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): from 6082407266, page 1 in 0:2 0, INF, 3.85 line/mm, 2-D MR, 14400 bit/s Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): recvq/fax00005.tif from 608240 7266, route to <unspecified>, 1 pages in 0:25 Apr 04 09:25:19.48: [ 4447]: <-- [7:AT+FDR\r] Apr 04 09:25:22.53: [ 4447]: --> [7:+FHNG:0] Apr 04 09:25:22.53: [ 4447]: REMOTE HANGUP: Normal and proper end of connection (code 0) Apr 04 09:25:22.53: [ 4447]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif" "ttyR1" "00000005" "" Apr 04 09:25:22.64: [ 4447]: RECV FAX: end Apr 04 09:25:22.64: [ 4447]: SESSION END Now today, there were no problems with incoming faxes. Yet NO CHANGES were made! Here's a log from a successful receive (see below): Apr 05 09:22:46.16: [ 916]: SESSION BEGIN 00000022 12626584152 Apr 05 09:22:46.16: [ 916]: <-- [4:ATA\r] Apr 05 09:22:55.77: [ 916]: --> [5:+FCON] Apr 05 09:22:55.77: [ 916]: ANSWER: FAX CONNECTION Apr 05 09:22:55.77: [ 916]: RECV FAX: begin Apr 05 09:23:01.00: [ 916]: --> [28:+FTSI:" 6082407266"] Apr 05 09:23:01.00: [ 916]: REMOTE TSI "6082407266" Apr 05 09:23:01.00: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,3] Apr 05 09:23:01.00: [ 916]: REMOTE wants 14400 bit/s Apr 05 09:23:01.00: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 09:23:01.00: [ 916]: REMOTE wants unlimited page length Apr 05 09:23:01.00: [ 916]: REMOTE wants 3.85 line/mm Apr 05 09:23:01.00: [ 916]: REMOTE wants 2-D MR Apr 05 09:23:01.00: [ 916]: --> [2:OK] Apr 05 09:23:01.00: [ 916]: <-- [7:AT+FDR\r] Apr 05 09:23:02.45: [ 916]: --> [5:+FCFR] Apr 05 09:23:02.45: [ 916]: --> [28:+FTSI:" 6082407266"] Apr 05 09:23:02.45: [ 916]: REMOTE TSI "6082407266" Apr 05 09:23:02.45: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,3] Apr 05 09:23:02.45: [ 916]: REMOTE wants 14400 bit/s Apr 05 09:23:02.45: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 09:23:02.45: [ 916]: REMOTE wants unlimited page length Apr 05 09:23:02.45: [ 916]: REMOTE wants unlimited page length Apr 05 09:23:02.45: [ 916]: REMOTE wants 3.85 line/mm Apr 05 09:23:02.45: [ 916]: REMOTE wants 2-D MR Apr 05 09:23:03.95: [ 916]: --> [7:CONNECT] Apr 05 09:23:03.95: [ 916]: RECV: begin page Apr 05 09:23:03.95: [ 916]: RECV: send trigger 022 Apr 05 09:23:03.95: [ 916]: <-- data [1] Apr 05 09:23:19.64: [ 916]: RECV: 26700 bytes of data, 1060 total lines Apr 05 09:23:19.64: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 09:23:20.92: [ 916]: --> [6:+FET:2] Apr 05 09:23:20.92: [ 916]: RECV recv EOP (no more pages or documents) Apr 05 09:23:20.92: [ 916]: --> [2:OK] Apr 05 09:23:20.92: [ 916]: RECV send MCF (message confirmation) Apr 05 09:23:20.92: [ 916]: RECV FAX (00000022): from 6082407266, page 1 in 0:1 9, INF, 3.85 line/mm, 2-D MR, 14400 bit/s Apr 05 09:23:20.92: [ 916]: RECV FAX (00000022): recvq/fax00018.tif from 608240 7266, route to <unspecified>, 1 pages in 0:25 Apr 05 09:23:20.92: [ 916]: <-- [7:AT+FDR\r] Apr 05 09:23:24.02: [ 916]: --> [7:+FHNG:0] Apr 05 09:23:24.02: [ 916]: REMOTE HANGUP: Normal and proper end of connection (code 0) Apr 05 09:23:24.02: [ 916]: RECV FAX: bin/faxrcvd "recvq/fax00018.tif" "ttyR0" "00000022" "" Apr 05 09:23:02.45: [ 916]: REMOTE wants 2-D MR Apr 05 09:23:03.95: [ 916]: --> [7:CONNECT] Apr 05 09:23:03.95: [ 916]: RECV: begin page Apr 05 09:23:03.95: [ 916]: RECV: send trigger 022 Apr 05 09:23:03.95: [ 916]: <-- data [1] Apr 05 09:23:19.64: [ 916]: RECV: 26700 bytes of data, 1060 total lines Apr 05 09:23:19.64: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 09:23:20.92: [ 916]: --> [6:+FET:2] Apr 05 09:23:20.92: [ 916]: RECV recv EOP (no more pages or documents) Apr 05 09:23:20.92: [ 916]: --> [2:OK] Apr 05 09:23:20.92: [ 916]: RECV send MCF (message confirmation) Apr 05 09:23:20.92: [ 916]: RECV FAX (00000022): from 6082407266, page 1 in 0:1 9, INF, 3.85 line/mm, 2-D MR, 14400 bit/s Apr 05 09:23:20.92: [ 916]: RECV FAX (00000022): recvq/fax00018.tif from 608240 7266, route to <unspecified>, 1 pages in 0:25 Apr 05 09:23:20.92: [ 916]: <-- [7:AT+FDR\r] Apr 05 09:23:24.02: [ 916]: --> [7:+FHNG:0] Apr 05 09:23:24.02: [ 916]: REMOTE HANGUP: Normal and proper end of connection (code 0) Apr 05 09:23:24.02: [ 916]: RECV FAX: bin/faxrcvd "recvq/fax00018.tif" "ttyR0" "00000022" "" Apr 05 09:23:24.13: [ 916]: RECV FAX: end Apr 05 09:23:24.13: [ 916]: SESSION END I decided to use one of the suggestions I recently read to have the modem perform QC on the line so I implemented the command in the config.ttyR0 script (and my other three lines): Class2CQQueryCmd: "!(0),(0)". Upon doing that (I had to let one incoming fax go through before the command took hold) suddenly I began receving major errors and the fax was rejected! This happened with my "sure bet" Richoh which had never failed to send a fax to my Hylafax server. Here's the log.... Apr 05 11:15:56.63: [ 916]: SESSION BEGIN 00000028 12626584152 Apr 05 11:15:56.63: [ 916]: <-- [4:ATA\r] Apr 05 11:16:04.73: [ 916]: --> [5:+FCON] Apr 05 11:16:04.73: [ 916]: ANSWER: FAX CONNECTION Apr 05 11:16:04.73: [ 916]: RECV FAX: begin Apr 05 11:16:10.05: [ 916]: --> [28:+FTSI:" 2626584152"] Apr 05 11:16:10.05: [ 916]: REMOTE TSI "2626584152" Apr 05 11:16:10.05: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:16:10.05: [ 916]: REMOTE wants 14400 bit/s Apr 05 11:16:10.05: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 11:16:10.05: [ 916]: REMOTE wants unlimited page length Apr 05 11:16:10.05: [ 916]: REMOTE wants 3.85 line/mm Apr 05 11:16:10.05: [ 916]: REMOTE wants 2-D MR Apr 05 11:16:10.05: [ 916]: --> [2:OK] Apr 05 11:16:10.05: [ 916]: <-- [7:AT+FDR\r] Apr 05 11:16:11.52: [ 916]: --> [5:+FCFR] Apr 05 11:16:11.52: [ 916]: --> [28:+FTSI:" 2626584152"] Apr 05 11:16:11.52: [ 916]: REMOTE TSI "2626584152" Apr 05 11:16:11.52: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:16:11.52: [ 916]: REMOTE wants 14400 bit/s Apr 05 11:16:11.52: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 11:16:11.52: [ 916]: REMOTE wants unlimited page length Apr 05 11:16:11.52: [ 916]: REMOTE wants unlimited page length Apr 05 11:16:11.52: [ 916]: REMOTE wants 3.85 line/mm Apr 05 11:16:11.52: [ 916]: REMOTE wants 2-D MR Apr 05 11:16:12.40: [ 916]: --> [7:CONNECT] Apr 05 11:16:12.40: [ 916]: RECV: begin page Apr 05 11:16:12.40: [ 916]: RECV: send trigger 022 Apr 05 11:16:12.40: [ 916]: <-- data [1] Apr 05 11:16:28.68: [ 916]: RECV: 1048 total lines, 976 bad lines, 60 consecuti ve bad lines Apr 05 11:16:28.68: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 11:16:29.96: [ 916]: --> [6:+FET:0] Apr 05 11:16:29.96: [ 916]: RECV recv MPS (more pages, same document) Apr 05 11:16:29.96: [ 916]: --> [2:OK] Apr 05 11:16:29.96: [ 916]: RECV: REJECT page quality, 6% good lines (95% requi red) Apr 05 11:16:29.96: [ 916]: RECV send RTN (retrain negative) Apr 05 11:16:29.96: [ 916]: <-- [10:AT+FPTS=2\r] Apr 05 11:16:30.22: [ 916]: --> [2:OK] Apr 05 11:16:30.22: [ 916]: <-- [7:AT+FDR\r] Apr 05 11:16:38.46: [ 916]: --> [5:+FCFR] Apr 05 11:16:38.46: [ 916]: --> [28:+FTSI:" 2626584152"] Apr 05 11:16:38.46: [ 916]: REMOTE TSI "2626584152" Apr 05 11:16:38.46: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:16:38.46: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:16:38.46: [ 916]: REMOTE wants 14400 bit/s Apr 05 11:16:38.46: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 11:16:38.46: [ 916]: REMOTE wants unlimited page length Apr 05 11:16:38.46: [ 916]: REMOTE wants 3.85 line/mm Apr 05 11:16:38.46: [ 916]: REMOTE wants 2-D MR Apr 05 11:16:39.32: [ 916]: --> [7:CONNECT] Apr 05 11:16:39.32: [ 916]: RECV: begin page Apr 05 11:16:39.32: [ 916]: RECV: send trigger 022 Apr 05 11:16:39.32: [ 916]: <-- data [1] Apr 05 11:16:55.49: [ 916]: RECV: 1050 total lines, 978 bad lines, 60 consecuti ve bad lines Apr 05 11:16:55.49: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 11:16:56.89: [ 916]: --> [6:+FET:0] Apr 05 11:16:56.89: [ 916]: RECV recv MPS (more pages, same document) Apr 05 11:16:56.89: [ 916]: --> [2:OK] Apr 05 11:16:56.89: [ 916]: RECV: REJECT page quality, 6% good lines (95% requi red) Apr 05 11:16:56.89: [ 916]: RECV send RTN (retrain negative) Apr 05 11:16:56.89: [ 916]: <-- [10:AT+FPTS=2\r] Apr 05 11:16:57.15: [ 916]: --> [2:OK] Apr 05 11:16:57.15: [ 916]: <-- [7:AT+FDR\r] Apr 05 11:17:05.37: [ 916]: --> [5:+FCFR] Apr 05 11:17:05.37: [ 916]: --> [5:+FCFR] Apr 05 11:17:05.37: [ 916]: --> [28:+FTSI:" 2626584152"] Apr 05 11:17:05.37: [ 916]: REMOTE TSI "2626584152" Apr 05 11:17:05.37: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:17:05.37: [ 916]: REMOTE wants 14400 bit/s Apr 05 11:17:05.37: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 11:17:05.37: [ 916]: REMOTE wants unlimited page length Apr 05 11:17:05.37: [ 916]: REMOTE wants 3.85 line/mm Apr 05 11:17:05.37: [ 916]: REMOTE wants 2-D MR Apr 05 11:17:06.23: [ 916]: --> [7:CONNECT] Apr 05 11:17:06.23: [ 916]: RECV: begin page Apr 05 11:17:06.23: [ 916]: RECV: send trigger 022 Apr 05 11:17:06.23: [ 916]: <-- data [1] Apr 05 11:17:22.51: [ 916]: RECV: 1050 total lines, 982 bad lines, 60 consecuti ve bad lines Apr 05 11:17:22.51: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 11:17:23.79: [ 916]: --> [6:+FET:0] Apr 05 11:17:23.79: [ 916]: RECV recv MPS (more pages, same document) Apr 05 11:17:23.79: [ 916]: --> [2:OK] Apr 05 11:17:23.79: [ 916]: RECV: REJECT page quality, 6% good lines (95% requi red) Apr 05 11:17:23.79: [ 916]: RECV send RTN (retrain negative) Apr 05 11:17:23.79: [ 916]: <-- [10:AT+FPTS=2\r] Apr 05 11:17:23.79: [ 916]: <-- [10:AT+FPTS=2\r] Apr 05 11:17:24.05: [ 916]: --> [2:OK] Apr 05 11:17:24.05: [ 916]: <-- [7:AT+FDR\r] Apr 05 11:17:32.29: [ 916]: --> [5:+FCFR] Apr 05 11:17:32.29: [ 916]: --> [28:+FTSI:" 2626584152"] Apr 05 11:17:32.29: [ 916]: REMOTE TSI "2626584152" Apr 05 11:17:32.29: [ 916]: --> [21:+FDCS:0,5,0,2,1,0,0,1] Apr 05 11:17:32.29: [ 916]: REMOTE wants 14400 bit/s Apr 05 11:17:32.29: [ 916]: REMOTE wants page width 1728 pixels in 215 mm Apr 05 11:17:32.29: [ 916]: REMOTE wants unlimited page length Apr 05 11:17:32.29: [ 916]: REMOTE wants 3.85 line/mm Apr 05 11:17:32.29: [ 916]: REMOTE wants 2-D MR Apr 05 11:17:33.15: [ 916]: --> [7:CONNECT] Apr 05 11:17:33.15: [ 916]: RECV: begin page Apr 05 11:17:33.15: [ 916]: RECV: send trigger 022 Apr 05 11:17:33.15: [ 916]: <-- data [1] Apr 05 11:17:49.43: [ 916]: RECV: 1050 total lines, 986 bad lines, 60 consecuti ve bad lines Apr 05 11:17:49.43: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 11:17:50.72: [ 916]: --> [6:+FET:0] Apr 05 11:17:50.72: [ 916]: RECV recv MPS (more pages, same document) Apr 05 11:17:50.72: [ 916]: --> [2:OK] Apr 05 11:17:50.72: [ 916]: RECV: REJECT page quality, 6% good lines (95% requi Apr 05 11:17:49.43: [ 916]: RECV: 1050 total lines, 986 bad lines, 60 consecuti ve bad lines Apr 05 11:17:49.43: [ 916]: --> [15:+FPTS:1,0,0,0,0] Apr 05 11:17:50.72: [ 916]: --> [6:+FET:0] Apr 05 11:17:50.72: [ 916]: RECV recv MPS (more pages, same document) Apr 05 11:17:50.72: [ 916]: --> [2:OK] Apr 05 11:17:50.72: [ 916]: RECV: REJECT page quality, 6% good lines (95% requi red) Apr 05 11:17:50.72: [ 916]: RECV send RTN (retrain negative) Apr 05 11:17:50.72: [ 916]: <-- [10:AT+FPTS=2\r] Apr 05 11:17:50.98: [ 916]: --> [2:OK] Apr 05 11:17:50.98: [ 916]: <-- [7:AT+FDR\r] Apr 05 11:17:53.93: [ 916]: --> [8:+FHNG:72] Apr 05 11:17:53.93: [ 916]: REMOTE HANGUP: COMREC error (code 72) Apr 05 11:17:53.93: [ 916]: RECV FAX (00000028): recvq/fax00024.tif from 262658 4152, route to <unspecified>, 0 pages in 1:49 Apr 05 11:17:53.93: [ 916]: RECV FAX: COMREC error Apr 05 11:17:53.93: [ 916]: RECV FAX (00000028): session with 2626584152 termin ated abnormally: COMREC error Apr 05 11:17:53.93: [ 916]: RECV FAX: bin/faxrcvd "recvq/fax00024.tif" "ttyR0" "00000028" "COMREC error" Apr 05 11:17:54.03: [ 916]: RECV FAX: end Apr 05 11:17:54.03: [ 916]: SESSION END After commenting out the QC line. Things are back to "normal". Here's my config script (you'll see the QC line commented out): # $Id: mt-1432,v 1.1.1.1 1998/10/12 20:47:47 root Exp $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems. # # MT1432 firmware rev 0307 I or newer # MT132BG rev 0109A # MT1932ZDX rev 0109H # # Note that MT1432 modems come in several varieties: # # MT1432BA uses Rockwell data pump # MT1432BA/A uses AT&T data pump # MT1432BG MT1432BA tweaked for German FCC # MT1432MK (for UK?) # # The modem has been tried with both XON/XOFF and RTS/CTS flow # control; this configuration is for hardware flow control. # control; this configuration is for hardware flow control. # # CountryCode: 1 AreaCode: 262 FAXNumber: 1.262.658.4152 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "Laminated Products x4152" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%p of %%t" MaxRecvPages: 250 # # TagLineFormat: "From %%l|%c|Page %%p of %%t" MaxRecvPages: 250 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2 # use class 2 interface ModemRate: 57600 # lock rate for DCE-DTE communication ModemFlowControl: rtscts # default # ModemHardFlowCmd: AT&E4 # hardware flow control ModemSoftFlowCmd: AT&E5 # software flow control ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in class 2 # # NB: some models get confused by the @ # ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence # Class2RecvDataTrigger: "\022" # character sent to modem to start recv #Class2CQQueryCmd: "!(0),(0)" # Enable Quality Check by DF 040501 Any help would be greatly appreciated! I have read some people being given the suggestion of going to Class 1 faxing but we need to send and receive faxes. I am lead to believe that I need Class2 to do both. Correct me if I'm not right in that thought. Best Regards, Dennis Fellows dennis@lamtop.com ____________________ HylaFAX(tm) Users Mailing List _______________________ To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- Follow-Ups:
- Re: [hylafax-users] Incoming Faxes are being scrambled
- From: Lee Howard <faxguy@deanox.com>
- Re: [hylafax-users] Incoming Faxes are being scrambled
- Prev by Date: Re: [hylafax-users] Hylafax installed properly on Suse 6.4
- Next by Date: Re: [hylafax-users] Incoming Faxes are being scrambled
- Prev by thread: [hylafax-users] VIRUS IN A MAIL FOR YOU FROM fcartron@apm-online.fr
- Next by thread: Re: [hylafax-users] Incoming Faxes are being scrambled
- Index(es):
Project hosted by iFAX Solutions