[hylafax-users] faxgetty doesn't create valid tiffs

["Baumann Reto" <rbaumi@bluewin.ch>]

I installed the newset version of HylaFax (4.1beta2 from an rpm) on a SuSE
Linux.

I can start faxgetty without any error message. Faxgetty detects incoming
calls, get's them and seems to handle them quite nicely in the beginning.
But, it looks like, faxgetty never closes the modem connection. Modem keeps
being busy. The sending station (of the fax) tells, that everything went
fine.

I'm using a Micronet Shuttle 3000 modem in Fax Class 2.0 mode.

The tiff image which is generated in the recvq is only 8 bytes long and an
invalid tiff (invalid header). Any help would be appriciated...

Thanks in advance

Reto


log file:
Feb 14 22:42:21.85: [26904]: SESSION BEGIN 00000005 11111111
Feb 14 22:42:21.85: [26904]: <-- [4:ATA\r]
Feb 14 22:42:29.57: [26904]: --> [4:+FCO]
Feb 14 22:42:29.57: [26904]: ANSWER: FAX CONNECTION
Feb 14 22:42:29.57: [26904]: RECV FAX: begin
Feb 14 22:42:31.58: [26904]: --> [27:+FTI:"..."]
Feb 14 22:42:31.58: [26904]: REMOTE TSI "XXX"
Feb 14 22:42:31.58: [26904]: --> [20:+FCS:1,5,0,2,0,0,0,0]
Feb 14 22:42:31.58: [26904]: REMOTE wants 14400 bit/s
Feb 14 22:42:31.58: [26904]: REMOTE wants page width 1728 pixels in 215 mm
Feb 14 22:42:31.58: [26904]: REMOTE wants unlimited page length
Feb 14 22:42:31.58: [26904]: REMOTE wants 7.7 line/mm
Feb 14 22:42:31.58: [26904]: REMOTE wants 1-D MR
Feb 14 22:42:31.58: [26904]: --> [2:OK]
Feb 14 22:42:31.58: [26904]: <-- [7:AT+FDR\r]
Feb 14 22:42:36.66: [26904]: --> [7:CONNECT]
Feb 14 22:42:36.66: [26904]: RECV: begin page
Feb 14 22:42:36.66: [26904]: RECV: send trigger 022
Feb 14 22:42:36.66: [26904]: <-- data [1]

====================================
modem config file (relevant part)

ModemType:              Class2.0        # use this to supply a hint
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality
proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null