[hylafax-users] Recieve trouble

["Work" <dmercer@stratcom.ca>]

I have included an example of a failure to receive (I have tried sending
from a number of different machines...all result the  same thing).

Sending is no problem...

Any help would be appreciated


Feb 07 16:12:09.05: [  864]: SESSION BEGIN 00000026 16046046812025
Feb 07 16:12:09.05: [  864]: <-- [4:ATA\r]
Feb 07 16:12:18.28: [  864]: --> [5:+FCON]
Feb 07 16:12:18.29: [  864]: ANSWER: FAX CONNECTION
Feb 07 16:12:18.29: [  864]: RECV FAX: begin
Feb 07 16:12:20.04: [  864]: --> [28:+FTSI:"          6047096195"]
Feb 07 16:12:20.05: [  864]: REMOTE TSI "6047096195"
Feb 07 16:12:20.32: [  864]: --> [21:+FDCS:0,3,0,2,0,0,0,3]
Feb 07 16:12:20.33: [  864]: REMOTE wants 9600 bit/s
Feb 07 16:12:20.33: [  864]: REMOTE wants page width 1728 pixels in 215 mm
Feb 07 16:12:20.33: [  864]: REMOTE wants unlimited page length
Feb 07 16:12:20.33: [  864]: REMOTE wants 3.85 line/mm
Feb 07 16:12:20.33: [  864]: REMOTE wants 1-D MR
Feb 07 16:12:20.33: [  864]: --> [2:OK]
Feb 07 16:12:20.33: [  864]: <-- [7:AT+FDR\r]
Feb 07 16:12:22.21: [  864]: --> [5:+FCFR]
Feb 07 16:12:24.21: [  864]: --> [7:CONNECT]
Feb 07 16:12:24.22: [  864]: RECV: begin page
Feb 07 16:12:24.22: [  864]: RECV: send trigger 021
Feb 07 16:13:44.22: [  864]: RECV: Missing EOL after 5 seconds
Feb 07 16:13:44.22: [  864]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)
Feb 07 16:13:44.22: [  864]: RECV FAX (00000026): recvq/fax00007.tif from
6047096195, route to <unspecified>, 0 pages in 1:26
Feb 07 16:13:44.22: [  864]: RECV FAX: Missing EOL after 5 seconds (section
3.2/T.4)
Feb 07 16:13:44.22: [  864]: <-- [6:AT+FK\r]
Feb 07 16:13:45.89: [  864]: --> [2:  ]
Feb 07 16:13:45.90: [  864]: --> [7:+FHNG:2]
Feb 07 16:13:45.90: [  864]: REMOTE HANGUP: Call aborted,  from +FK or <CAN>
(code 2)
Feb 07 16:13:46.25: [  864]: --> [2:OK]
Feb 07 16:13:46.26: [  864]: RECV FAX (00000026): session with 6047096195
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Feb 07 16:13:46.26: [  864]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif"
"ttyS0" "00000026" "Missing EOL after 5 seconds (section 3.2/T.4)"



Below is the configuration for the modem

# $Id: class2,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		604
FAXNumber:		604.681.2025
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Strategic Communications"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:		AT+FCLASS=2	# command to enter class 2
Class2BORCmd:		AT+FBOR=0	# bit order for phase B/C/D (direct)
Class2RELCmd:		AT+FREL=1	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FK		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FDCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FTBC=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FPHCTO=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBUG=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLID		# set local identifier command
Class2DCCCmd:		AT+FDCC		# set modem capabilities command
Class2DISCmd:		AT+FDIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FCIG		# set polling identifier command
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2SPLCmd:		AT+FSPL		# set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:	""		# character sent to modem to start recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null