Re: [hylafax-users] FW: facsimile received from

["Budi Gautama" <budig@apakabar.com>]

Thanks for your response, can you please advise what modem is best for
Hylafax.

Budi

> -----Original Message-----
> From: hylafax-users-bounce@hylafax.org
> [mailto:hylafax-users-bounce@hylafax.org]On Behalf Of Dmitry Bely
> Sent: Thursday, September 14, 2000 10:56 AM
> To: hylafax-users@hylafax.org
> Subject: Re: [hylafax-users] FW: facsimile received from
>
>
> "Budi Gautama" <budig@apakabar.com> writes:
>
> > I have problem in receiving fax from certain fax machines,
> error message as
> > follows.
> >
> > Pls help.
> >
> > Budi
> >
> > -----Original Message-----
> > From: The HylaFAX Receive Agent [mailto:fax@hirawan.centrin.net.id]
> > Sent: Thursday, September 14, 2000 10:45 AM
> > To: hirawan@bdg.centrin.net.id
> > Subject: facsimile received from
> >
> >
> > recvq/fax00025.tif
> (ftp://hirawan.centrin.net.id:4559/recvq/fax00025.tif):
> >     Sender:
> >      Pages: 2
> >    Quality: Fine
> >       Page: 1728 by 144
> >   Received: 2000:09:14 05:43:05
> > TimeToRecv: 5:01:39
> > SignalRate: 14400 bit/s
> > DataFormat: 1-D MR
> > ReceivedOn: ttyS0
> >
> > The full document was not received because:
> >
> >     Unspecified Phase C error, including too much delay between
> TCF and +FDR
> > command
> >
> >     ---- Transcript of session follows ----
> >
> > Sep 14 05:42:50.44: [ 7250]: SESSION BEGIN 00000041 62224250025
> > Sep 14 05:42:50.44: [ 7250]: <-- [4:ATA\r]
> > Sep 14 05:42:52.94: [ 7250]: --> [3:FAX]
> > Sep 14 05:42:58.64: [ 7250]: --> [5:+FCON]
> > Sep 14 05:42:58.64: [ 7250]: ANSWER: FAX CONNECTION
> > Sep 14 05:42:58.64: [ 7250]: RECV FAX: begin
> > Sep 14 05:42:59.87: [ 7250]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
> > Sep 14 05:42:59.87: [ 7250]: REMOTE wants 14400 bit/s
> > Sep 14 05:42:59.87: [ 7250]: REMOTE wants page width 1728
> pixels in 215 mm
> > Sep 14 05:42:59.87: [ 7250]: REMOTE wants unlimited page length
> > Sep 14 05:42:59.87: [ 7250]: REMOTE wants 7.7 line/mm
> > Sep 14 05:42:59.87: [ 7250]: REMOTE wants 1-D MR
> > Sep 14 05:42:59.98: [ 7250]: --> [2:OK]
> > Sep 14 05:42:59.98: [ 7250]: <-- [7:AT+FDR\r]
> > Sep 14 05:43:03.05: [ 7250]: --> [5:+FCFR]
> > Sep 14 05:43:05.05: [ 7250]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
> > Sep 14 05:43:05.05: [ 7250]: REMOTE wants 14400 bit/s
> > Sep 14 05:43:05.05: [ 7250]: REMOTE wants page width 1728
> pixels in 215 mm
> > Sep 14 05:43:05.05: [ 7250]: REMOTE wants unlimited page length
> > Sep 14 05:43:05.05: [ 7250]: REMOTE wants 7.7 line/mm
> > Sep 14 05:43:05.05: [ 7250]: REMOTE wants 1-D MR
> > Sep 14 05:43:05.05: [ 7250]: --> [7:CONNECT]
> > Sep 14 05:43:05.05: [ 7250]: RECV: begin page
> > Sep 14 05:43:05.05: [ 7250]: RECV: send trigger 022
> > Sep 14 05:43:10.24: [ 7250]: RECV: 1116 total lines, 0 bad
> lines, 0 consecutive bad lines
> > Sep 14 05:43:10.24: [ 7250]: --> [17:+FPTS: 1,2219,0,0]
> > Sep 14 05:43:11.71: [ 7250]: --> [7:+FET: 0]
> > Sep 14 05:43:11.71: [ 7250]: RECV recv MPS (more pages, same document)
> > Sep 14 05:43:11.71: [ 7250]: --> [2:OK]
> > Sep 14 05:43:11.71: [ 7250]: RECV send MCF (message confirmation)
> > Sep 14 05:43:11.72: [ 7250]: RECV FAX (00000041): from
> <UNSPECIFIED>, page 1 in 0:12, INF, 7.7 line/mm, 1-D MR
> > Sep 14 05:43:11.72: [ 7250]: <-- [7:AT+FDR\r]
> > Sep 14 05:43:13.62: [ 7250]: --> [7:CONNECT]
> > Sep 14 05:43:13.62: [ 7250]: RECV: begin page
> > Sep 14 05:43:13.62: [ 7250]: RECV: send trigger 022
> > Sep 14 10:44:39.93: [ 7250]: RECV: 25089 total lines, 24117 bad
> lines, 858 consecutive bad lines
>
> Either the connection was incorrectly terminated (remote had gone on-hook
> and your modem just got a garbage here) or your modem's firmware is broken
> completely.
>
> > Sep 14 10:44:39.93: [ 7250]: --> [17:+FPTS: 2,2219,0,0]
> > Sep 14 10:45:09.93: [ 7250]: MODEM <Timeout>
>
> The later assumption (the broken firmware) is more possible. Even having
> the complete garbage from the remote the modem should *correctly*
> report an
> error. But it did not...
>
> > Sep 14 10:45:09.93: [ 7250]: REMOTE HANGUP: Unspecified Phase C error,
> > including too much delay between TCF and +FDR command (code 90)
> > Sep 14 10:45:09.93: [ 7250]: RECV FAX (00000041):
> recvq/fax00025.tif from <UNSPECIFIED>, route to <unspecified>, 1
> pages in 5:02:11
> > Sep 14 10:45:09.93: [ 7250]: RECV FAX: Unspecified Phase C
> error, including
> > too much delay between TCF and +FDR command
> > Sep 14 10:45:09.93: [ 7250]: <-- [6:AT+FK\r]
> > Sep 14 10:45:21.53: [ 7250]: --> [10:+FHNG: 101]
> > Sep 14 10:45:21.53: [ 7250]: REMOTE HANGUP: RSPREC invalid
> response received
> > (code 101)
> > Sep 14 10:45:23.36: [ 7250]: --> [2:OK]
> > Sep 14 10:45:23.36: [ 7250]: RECV FAX (00000041): session with
> <UNSPECIFIED>
> > terminated abnormally: Unspecified Phase C error, including too
> much delay between TCF and +FDR command
> > Sep 14 10:45:23.36: [ 7250]: RECV FAX: bin/faxrcvd "recvq/fax00025.tif"
> > "ttyS0" "00000041" "Unspecified Phase C error, including too much delay
> > between TCF and +FDR command"
>
> Summary: you cannot fix it at the software level. Try better
> modem or wait for
> 4.1 beta 3 and switch to Class1 mode.
>
> Hope to hear from you soon,
> Dmitry
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>  To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org
> < /dev/null
>



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null