Re: flexfax: Trouble receiving Faxes with Elsa Microlink 56k Basic Modem

["Claas Hilbrecht" <Claas.Hilbrecht@linum.com>]

Hello,

I have no problems with the same hard-/software combination. I will 
give you some details from my setup.

> - Suse 6.4

Same here, with latest patches as off 11.05.2000

> - Hylafax 4.1 beta 2

hylafax-4.1beta2-61

> - Elsa Microlink 56k basic

I also use this modem. Currently installed is firmware 1.20. Here is my 
config.ttySx file.

#
# Class 2.0 modem configuration for ELSA Modems with V.250 command set.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            49
AreaCode:               5561
FAXNumber:              "+49 5561 971071"
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules.europe
ServerTracing:          0x3ff2f
SessionTracing:         0x3ff2f
RecvFileMode:           0666
LogFileMode:            0666
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "+49 5561 971071"
LogFacility:            local0
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "Von: %%l an: %%d|%d.%m.%Y %H:%M Seite %%p von 
%%t"
PercentGoodLines:       80
MaxConsecutiveBadLines: 20
MaxRecvPages:           999
ModemPriority:          200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              115200          # max rate for DCE-DTE 
communication
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets 
modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier 
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDT%s
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:         ATX3            # stuff to do when modem is 
reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT+IFC=0,0;
ModemHardFlowCmd:       AT+IFC=2,2;
ModemSoftFlowCmd:       AT+IFC=1,1;
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command 
results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received 
facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for 
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D 
(direct)
Class2CQCmd:            ""              # commands to enable copy 
quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality 
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities 
command
Class2DISCmd:           AT+FIS          # set session parameters 
command
Class2DDISCmd:          ""              # disable pre-dial DIS command 
hack
Class2CIGCmd:           AT+FPI          # set polling identifier 
command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting 
command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable 
command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control 
command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control 
command


Mit freundlichem Gruss
Claas Hilbrecht

Linum Software GmbH
http://www.linum.com
Tel: 05561-971070
Fax: 05561-971071