Re: flexfax: Missing EOL after 5 seconds

["Horst Simon" <hsimon@vic.bigpond.net.au>]

Thanks Dmitr, this fixed the EOL problem, but now I have a different error
with no data
received.
Anyone has information or fix suggestions on this one
Thanks and Regards
Horst Simon

Mar 05 08:02:13.29: [  327]: SESSION BEGIN 00000022 610395531624
Mar 05 08:02:13.29: [  327]: <-- [4:ATA\r]
Mar 05 08:02:24.25: [  327]: --> [5:+FCON]
Mar 05 08:02:24.25: [  327]: ANSWER: FAX CONNECTION
Mar 05 08:02:24.25: [  327]: RECV FAX: begin
Mar 05 08:02:24.55: [  327]: --> [28:+FTSI:"+613 9553-1624      "]
Mar 05 08:02:24.55: [  327]: REMOTE TSI "+613 9553-1624"
Mar 05 08:02:26.66: [  327]: --> [21:+FDCS:1,3,0,2,0,0,0,3]
Mar 05 08:02:26.66: [  327]: REMOTE wants 9600 bit/s
Mar 05 08:02:26.66: [  327]: REMOTE wants page width 1728 pixels in 215 mm
Mar 05 08:02:26.66: [  327]: REMOTE wants unlimited page length
Mar 05 08:02:26.66: [  327]: REMOTE wants 7.7 line/mm
Mar 05 08:02:26.66: [  327]: REMOTE wants 1-D MR
Mar 05 08:02:26.66: [  327]: --> [2:OK]
Mar 05 08:02:26.67: [  327]: <-- [7:AT+FDR\r]
Mar 05 08:02:28.17: [  327]: --> [5:+FCFR]
Mar 05 08:02:28.84: [  327]: --> [7:CONNECT]
Mar 05 08:02:28.84: [  327]: RECV: begin page
Mar 05 08:02:28.84: [  327]: RECV: send trigger 022
Mar 05 08:02:28.84: [  327]: <-- data [1]
Mar 05 08:02:57.41: [  327]: RECV: 0 total lines, 0 bad lines, 0 consecutive
bad lines
Mar 05 08:02:57.41: [  327]: --> [12:+FPTS:1,2145]
Mar 05 08:02:58.70: [  327]: --> [6:+FET:2]
Mar 05 08:02:58.70: [  327]: RECV recv EOP (no more pages or documents)
Mar 05 08:02:58.70: [  327]: --> [2:OK]
Mar 05 08:02:58.72: [  327]: RECV send MCF (message confirmation)
Mar 05 08:02:58.73: [  327]: RECV FAX (00000022): from +613 9553-1624, page
1 in 0:32, INF, 7.7 line/mm, 1-D MR
Mar 05 08:02:58.75: [  327]: RECV FAX (00000022): recvq/fax00011.tif from
+613 9553-1624, route to <unspecified>, 1 pages in 0:34
Mar 05 08:02:58.80: [  327]: <-- [7:AT+FDR\r]
Mar 05 08:03:01.56: [  327]: --> [7:+FHNG:0]
Mar 05 08:03:01.56: [  327]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Mar 05 08:03:01.56: [  327]: RECV FAX: bin/faxrcvd "recvq/fax00011.tif"
"cua0" "00000022" ""
Mar 05 08:03:05.17: [  327]: RECV FAX: end
Mar 05 08:03:05.17: [  327]: SESSION END

Horst Simon wrote:

> This is a follow-up on my first message having Phase B errors. After
> changing
> the baud rate to 19.2k and enabling XON/XOFF, I am getting now missing EOL
> after
> 5 seconds errors.
>
> Sending faxes works ok, only receive fails.
>
> Anyone has seen this error and could fix it? Any suggestions appreciated.
>
> Thanks and Regards,
> Horst Simon
>

Try to change receive trigger value:

Class2RecvDataTrigger:  "\022"

I had the same problem as you and it helped me (of course it depends on the
modem you use).

With best regards,
Dmitry Bely
Moscow/Russia


===============================
|   Horst Simon               |
|   9 Stonehaven Crescent     |
|   Moorabbin, Vic, 3189      |
|   Australia                 |
|   hsimon@vic.bigpond.net.au |
===============================