Re: flexfax: Fwd: facsimile job 2 to 31 failed

[Damian Ivereigh <damian@cisco.com>]

Hi Thomas,

Your problem is in the dialrules. Where are you in the world? You
probably should be using dialrules.europe.

I think you are also getting confused between "no dialtone" and "no
carrier". "no dialtone" means that modem picked up the line and couldn't
hear anything coming from the exchange - it means the phone line
probably isn't plugged in. "no carrier", means that the modem dialled,
but didn't get a response (or one that it could understand) from the far
end.

I have annotated the log below:-

> ----------  Weitergeleitete Nachricht  ----------
> Subject: facsimile job 2 to 31 failed
> Date: Thu, 12 Nov 1998 16:56:05 GMT
> From: Facsimile Agent <fax@awd.at>
> 
> Your facsimile job to 31 failed because:
>     No carrier detected
> 
>     ---- Transcript of session follows ----
> 
> Nov 12 16:54:41.24: [ 1117]: SESSION BEGIN 00000020 43131
> Nov 12 16:54:41.24: [ 1117]: SEND FAX: JOB 2 DEST 31 COMMID 00000020
> Nov 12 16:54:41.24: [ 1117]: MODEM set DTR OFF
> Nov 12 16:54:41.24: [ 1117]: DELAY 2600 ms
> Nov 12 16:54:43.85: [ 1117]: MODEM set DTR ON
> Nov 12 16:54:43.85: [ 1117]: MODEM set baud rate: 9600 baud, input flow XON/XOFF, output flow XON/XOFF
> Nov 12 16:54:43.85: [ 1117]: MODEM flush i/o
> Nov 12 16:54:43.85: [ 1117]: <-- [17:ATE0V1Q0X4S0=0H0\r]
> Nov 12 16:54:44.02: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.02: [ 1117]: <-- [32:ATS8=2S7=60&H2&I2&R1S13=1&D2&C1\r]
> Nov 12 16:54:44.19: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.19: [ 1117]: <-- [14:AT+FCLASS=2.0\r]
> Nov 12 16:54:44.35: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.35: [ 1117]: <-- [9:AT+FLO=1\r]
> Nov 12 16:54:44.50: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.50: [ 1117]: <-- [9:AT+FPP=0\r]
> Nov 12 16:54:44.65: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.65: [ 1117]: <-- [9:AT+FBO=0\r]
> Nov 12 16:54:44.80: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.80: [ 1117]: <-- [10:AT+FCT=30\r]
> Nov 12 16:54:44.95: [ 1117]: --> [2:OK]
> Nov 12 16:54:44.95: [ 1117]: <-- [15:AT+FNR=1,1,1,0\r]
> Nov 12 16:54:45.11: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.11: [ 1117]: <-- [9:AT+FIE=0\r]
> Nov 12 16:54:45.26: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.26: [ 1117]: <-- [9:AT+FBU=0\r]
> Nov 12 16:54:45.41: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.41: [ 1117]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Nov 12 16:54:45.58: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.58: [ 1117]: <-- [5:ATM0\r]
> Nov 12 16:54:45.73: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.73: [ 1117]: STATE CHANGE: RUNNING -> SENDING
> Nov 12 16:54:45.73: [ 1117]: MODEM input buffering enabled
> Nov 12 16:54:45.73: [ 1117]: Apply DialString rules to "31"
> Nov 12 16:54:45.73: [ 1117]: --> return result "31"
> Nov 12 16:54:45.73: [ 1117]: <-- [14:AT+FCLASS=2.0\r]
> Nov 12 16:54:45.99: [ 1117]: --> [2:OK]
> Nov 12 16:54:45.99: [ 1117]: <-- [9:AT+FLO=1\r]
> Nov 12 16:54:46.24: [ 1117]: --> [2:OK]
> Nov 12 16:54:46.24: [ 1117]: <-- [9:AT+FPP=0\r]
> Nov 12 16:54:46.49: [ 1117]: --> [2:OK]
> Nov 12 16:54:46.49: [ 1117]: <-- [9:AT+FBO=0\r]
> Nov 12 16:54:46.74: [ 1117]: --> [2:OK]
> Nov 12 16:54:46.74: [ 1117]: <-- [10:AT+FCT=30\r]
> Nov 12 16:54:46.99: [ 1117]: --> [2:OK]
> Nov 12 16:54:46.99: [ 1117]: <-- [15:AT+FNR=1,1,1,0\r]
> Nov 12 16:54:47.25: [ 1117]: --> [2:OK]
> Nov 12 16:54:47.25: [ 1117]: <-- [9:AT+FIE=0\r]
> Nov 12 16:54:47.50: [ 1117]: --> [2:OK]
> Nov 12 16:54:47.50: [ 1117]: <-- [9:AT+FBU=0\r]
> Nov 12 16:54:47.75: [ 1117]: --> [2:OK]
> Nov 12 16:54:47.75: [ 1117]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Nov 12 16:54:48.02: [ 1117]: --> [2:OK]
> Nov 12 16:54:48.02: [ 1117]: <-- [27:AT+FLI="AWD Zentrale Wien"\r]
> Nov 12 16:54:48.29: [ 1117]: --> [2:OK]
> Nov 12 16:54:48.30: [ 1117]: DIAL 31

This doesn't seem right. Is the telephone number really '31'? This is
why I think your dialrules are not right. 

> Nov 12 16:54:48.30: [ 1117]: <-- [11:ATX1DT0,31\r]
> Nov 12 16:56:03.15: [ 1117]: --> [10:NO CARRIER]

Note "no carrier", not "no dialtone"

> Nov 12 16:56:03.15: [ 1117]: SEND FAILED: No carrier detected
> Nov 12 16:56:03.15: [ 1117]: <-- [5:ATH0\r]
> Nov 12 16:56:03.40: [ 1117]: --> [2:OK]
> Nov 12 16:56:03.40: [ 1117]: MODEM set DTR OFF
> Nov 12 16:56:03.40: [ 1117]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
> Nov 12 16:56:03.40: [ 1117]: SESSION END

If you want I can help you set up the other stuff like country codes and
area codes, just let me know.

Damian

-- 
 ______________________________________________________________________
* Damian Ivereigh     *      ||        ||      * Cisco Systems, Inc.   *
* MIS Printer Admin   *    .||||.    .||||.    * Sydney, Australia     *
* Linux Bigot         * ..:||||||:..:||||||:.. * +61 2 8448 7344       *
* damian@cisco.com    *   cisco Systems, Inc.  * Fax: +61 2 8448 7228  *
*______________________________________________________________________*