flexfax: Got disconnected before SEND FILE

[Thidarat Pornkarnchananun <pornkarn@fsl.noaa.gov>]

Hi all,
Has anyone seen this problem before?
I run Hylafax v.4.0pl2 on HPUX10.20 and Linux with MultiTech2834ZDXb
faxmodem. On both platforms, the problem was the modem dialed out and
got connected but immediately disconnected. Here is what I found in the
system log file:

Aug 20 16:25:24 sudo: pornkarn : TTY=ttyp3 ; PWD=/var/spool/fax ;
USER=root
 ; COMMAND=/usr/local/sbin/faxsend -m cua0 sendq/q7
Aug 20 16:25:32 FaxSend[824]: MODEM MULTI-TECH SYSTEMS MT2834ZDX/0316A
Aug 20 16:25:32 FaxSend[824]: SEND FAX: JOB 7 DEST 7259 COMMID 00000008
Aug 20 16:25:38 FaxQueuer[772]: FIFO RECV "*7:c"
Aug 20 16:25:55 FaxQueuer[772]: FIFO RECV "*7:C"

Then everything's gone.  And in the log files:

Aug 20 16:25:32.50: [  824]: SESSION BEGIN 00000008 13037259
Aug 20 16:25:32.50: [  824]: SEND FAX: JOB 7 DEST 7259 COMMID 00000008
Aug 20 16:25:32.50: [  824]: DELAY 2600 ms
Aug 20 16:25:35.11: [  824]: <-- [15:ATE0V1Q0S0=0H0\r]
Aug 20 16:25:35.30: [  824]: --> [2:OK]
Aug 20 16:25:35.30: [  824]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
Aug 20 16:25:35.49: [  824]: --> [2:OK]
Aug 20 16:25:35.49: [  824]: <-- [12:AT+FCLASS=2\r]
Aug 20 16:25:35.67: [  824]: --> [2:OK]
Aug 20 16:25:35.67: [  824]: <-- [10:AT+FTBC=0\r]
Aug 20 16:25:35.85: [  824]: --> [2:OK]
Aug 20 16:25:35.85: [  824]: <-- [10:AT+FBOR=0\r]
Aug 20 16:25:36.03: [  824]: --> [2:OK]
Aug 20 16:25:36.03: [  824]: <-- [13:AT+FPHCTO=30\r]
Aug 20 16:25:36.21: [  824]: --> [2:OK]
Aug 20 16:25:36.21: [  824]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Aug 20 16:25:36.41: [  824]: --> [2:OK]
Aug 20 16:25:36.41: [  824]: <-- [7:ATL0M1\r]
Aug 20 16:25:36.59: [  824]: --> [2:OK]
Aug 20 16:25:36.59: [  824]: <-- [12:AT+FCLASS=2\r]
Aug 20 16:25:36.87: [  824]: --> [2:OK]
Aug 20 16:25:36.87: [  824]: <-- [10:AT+FTBC=0\r]
Aug 20 16:25:37.15: [  824]: --> [2:OK]
Aug 20 16:25:37.15: [  824]: <-- [10:AT+FBOR=0\r]
Aug 20 16:25:37.43: [  824]: --> [2:OK]
Aug 20 16:25:37.43: [  824]: <-- [13:AT+FPHCTO=30\r]
Aug 20 16:25:37.71: [  824]: --> [2:OK]
Aug 20 16:25:37.71: [  824]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Aug 20 16:25:38.01: [  824]: --> [2:OK]
Aug 20 16:25:38.01: [  824]: <-- [15:AT+FLID="         "\r]
Aug 20 16:25:38.30: [  824]: --> [2:OK]
Aug 20 16:25:38.30: [  824]: DIAL 7259
Aug 20 16:25:38.30: [  824]: <-- [10:ATDT7259@\r]
Aug 20 16:25:55.20: [  824]: --> [5:+FCON]
Aug 20 16:25:57.24: [  824]: --> [57:+FNSF:00 00 79 00 00 00 16 0F 09 13
00 10 0
5 06 8D C0 50 ]
Aug 20 16:25:57.24: [  824]: REMOTE NSF "00 00 79 00 00 00 16 0F 09 13
00 10 05
06 8D C0 50"
Aug 20 16:25:57.24: [  824]: --> [21:+FDIS:1,3,0,2,1,2,0,4]
Aug 20 16:25:57.24: [  824]: --> [2:OK]
Aug 20 16:25:57.24: [  824]: REMOTE best rate 9600 bit/s
Aug 20 16:25:57.24: [  824]: REMOTE max page width 1728 pixels in 215 mm

Aug 20 16:25:57.24: [  824]: REMOTE max unlimited page length
Aug 20 16:25:57.24: [  824]: REMOTE best vres 7.7 line/mm
Aug 20 16:25:57.24: [  824]: REMOTE best format 2-D MR
Aug 20 16:25:57.24: [  824]: REMOTE supports T.30 Annex C, half duplex
ECM
Aug 20 16:25:57.24: [  824]: REMOTE best 20 ms, 10 ms/scanline
Aug 20 16:25:57.24: [  824]: USE 9600 bit/s
Aug 20 16:25:57.24: [  824]: USE 20 ms, 10 ms/scanline
Aug 20 16:25:57.24: [  824]: <-- [5:ATH0\r]
Aug 20 16:25:58.86: [  824]: --> [7:+FHNG:2]
Aug 20 16:25:58.86: [  824]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (co
de 2)
Aug 20 16:25:59.51: [  824]: --> [2:OK]
Aug 20 16:25:59.51: [  824]: SESSION END

It seems to me like the software always hangs up the transmission before
SEND FILE happens.
Could any of you give me some hints what might cause this and how to
fix?
Any help would be very appreciated.
Best regards,
Thidarat
--
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Thidarat Pornkarnchananun
pornkarn@fsl.noaa.gov
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~