flexfax: FaxSend message: Invalid dialing command

["Jrgen Siepmann" <siepmann@euro-ticket.de>]

Hello,

I have the US-Robotics Sportster Message Plus Modem and I get the
following message in /var/log/messages when I try to send a Fax.

Platform:       Linux, Kernel 2.0.33,
Hylafax:        4.0pl2

------------------------------------------------------------------------

May 28 17:16:08 linux FaxSend[378]: MODEM input buffering disabled
May 28 17:16:08 linux FaxSend[378]: Apply CanonicalNumber rules to "06233 506085"
May 28 17:16:08 linux FaxSend[378]: --> match rule "[^+0-9]+", result now "06233506085"
May 28 17:16:08 linux FaxSend[378]: --> match rule "^0", result now "+496233506085"
May 28 17:16:08 linux FaxSend[378]: --> return result "+496233506085"
May 28 17:16:08 linux FaxSend[378]: Apply CanonicalNumber rules to "06233 506085"
May 28 17:16:08 linux FaxSend[378]: --> match rule "[^+0-9]+", result now "06233506085"
May 28 17:16:08 linux FaxSend[378]: --> match rule "^0", result now "+496233506085"
May 28 17:16:08 linux FaxSend[378]: --> return result "+496233506085"
May 28 17:16:08 linux FaxSend[378]: SEND FAX: JOB 21 DEST 06233 506085 COMMID 00000012
May 28 17:16:12 linux FaxSend[378]: SEND FAILED: Invalid dialing command
May 28 17:16:12 linux FaxQueuer[249]: JOB 21 (active dest +496233506085 pri 127 tts 0:00 killtime 2:58:45): CMD DONE: exit status 0
May 28 17:16:12 linux FaxQueuer[249]: JOB 21 (sleeping dest +496233506085 pri 126 tts 0:00 killtime 2:58:45): SEND INCOMPLETE: requeue for 3:11; Invalid dialing command
May 28 17:16:12 linux FaxQueuer[249]: NOTIFY: bin/notify "sendq/q21" "requeued" "" "17:19"
May 28 17:16:34 linux FaxGetty[258]: MODEM set DTR OFF

------------------------------------------------------------------------

I get the following mail from the faxmaster:

------------------------------------------------------------------------
Your facsimile job to 06233 506085 was not sent because:
    Invalid dialing command

The job will be retried at 17:25.

    ---- Transcript of session follows ----

May 28 17:19:30.23: [  389]: SESSION BEGIN 00000013 496233506085
May 28 17:19:30.23: [  389]: SEND FAX: JOB 21 DEST 06233 506085 COMMID 00000013
May 28 17:19:30.23: [  389]: MODEM set DTR OFF
May 28 17:19:30.23: [  389]: DELAY 2600 ms
May 28 17:19:32.84: [  389]: MODEM set DTR ON
May 28 17:19:32.84: [  389]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS
May 28 17:19:32.84: [  389]: MODEM flush i/o
May 28 17:19:32.84: [  389]: <-- [17:ATE0V1Q0X4S0=0H0\r]
May 28 17:19:32.98: [  389]: --> [2:OK]
May 28 17:19:32.98: [  389]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
May 28 17:19:33.14: [  389]: --> [2:OK]
May 28 17:19:33.14: [  389]: <-- [12:AT+FCLASS=1\r]
May 28 17:19:33.28: [  389]: --> [2:OK]
May 28 17:19:33.29: [  389]: <-- [12:AT&H1&I0&R2\r]
May 28 17:19:33.42: [  389]: --> [2:OK]
May 28 17:19:33.43: [  389]: <-- [21:AT+FCLASS=0&H1&I0&R2\r]
May 28 17:19:33.58: [  389]: --> [2:OK]
May 28 17:19:33.58: [  389]: <-- [5:ATM0\r]
May 28 17:19:33.72: [  389]: --> [2:OK]
May 28 17:19:33.72: [  389]: STATE CHANGE: RUNNING -> SENDING
May 28 17:19:33.72: [  389]: MODEM input buffering enabled
May 28 17:19:33.72: [  389]: Apply DialString rules to "06233 506085"
May 28 17:19:33.72: [  389]: --> match rule "[-         .]+", result now "06233506085"
May 28 17:19:33.72: [  389]: --> return result "06233506085"
May 28 17:19:33.72: [  389]: <-- [12:AT+FCLASS=1\r]
May 28 17:19:33.96: [  389]: --> [2:OK]
May 28 17:19:33.96: [  389]: <-- [12:AT&H1&I0&R2\r]
May 28 17:19:34.20: [  389]: --> [2:OK]
May 28 17:19:34.21: [  389]: DIAL 06233506085
May 28 17:19:34.21: [  389]: <-- [16:ATDT06233506085\r]
May 28 17:19:34.46: [  389]: --> [5:ERROR]
May 28 17:19:34.46: [  389]: SEND FAILED: Invalid dialing command
May 28 17:19:34.46: [  389]: <-- [5:ATH0\r]
May 28 17:19:34.70: [  389]: --> [2:OK]
May 28 17:19:34.70: [  389]: MODEM set DTR OFF
May 28 17:19:34.70: [  389]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
May 28 17:19:34.70: [  389]: SESSION END

------------------------------------------------------------------------

What's the reason. My dialing command ATDT06233506085 ist o.k.

J�rgen