Short Pages Cut

[nicolc@elsie.econ.uregina.ca (Chris Nicol)]

Hi. I just installed version 4.0pl1 of hylafax on a Linux machine
running kernel version 2.0.27. Everything seems to work fine, except
that, when a dociment sent with sendfax is short (doesn't take up a
full page of text), the page gets cut after the text, and does not end
up being an 8.5x11 in page. All the text gets transmitted, but the
page is cut after the text. Any ideas?

Here is a log from a transmission where this happened.

(I am using a USR Sportster 33.6 FAX modem, running it in Class 1 mode
-- under a previous version of Hylafax, I could not get Class 2.0 to
work reliably with this modem).



Jan 02 13:10:29.37: [ 1723]: SESSION BEGIN 00000008 13065854815
Jan 02 13:10:29.38: [ 1723]: SEND FAX: JOB 5 DEST 585-4815 COMMID 00000008
Jan 02 13:10:29.38: [ 1723]: DELAY 2600 ms
Jan 02 13:10:31.99: [ 1723]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jan 02 13:10:32.13: [ 1723]: --> [2:OK]
Jan 02 13:10:32.13: [ 1723]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Jan 02 13:10:32.27: [ 1723]: --> [2:OK]
Jan 02 13:10:32.27: [ 1723]: <-- [12:AT+FCLASS=1\r]
Jan 02 13:10:32.41: [ 1723]: --> [2:OK]
Jan 02 13:10:32.41: [ 1723]: <-- [12:AT&H1&I0&R2\r]
Jan 02 13:10:32.55: [ 1723]: --> [2:OK]
Jan 02 13:10:32.55: [ 1723]: <-- [21:AT+FCLASS=0&H1&I0&R2\r]
Jan 02 13:10:32.69: [ 1723]: --> [2:OK]
Jan 02 13:10:32.69: [ 1723]: <-- [7:ATL1M1\r]
Jan 02 13:10:32.83: [ 1723]: --> [2:OK]
Jan 02 13:10:32.84: [ 1723]: <-- [12:AT+FCLASS=1\r]
Jan 02 13:10:33.08: [ 1723]: --> [2:OK]
Jan 02 13:10:33.08: [ 1723]: <-- [12:AT&H1&I0&R2\r]
Jan 02 13:10:33.32: [ 1723]: --> [2:OK]
Jan 02 13:10:33.32: [ 1723]: DIAL 5854815
Jan 02 13:10:33.32: [ 1723]: <-- [12:ATDT5854815\r]
Jan 02 13:10:51.20: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:52.81: [ 1723]: --> [2:OK]
Jan 02 13:10:52.81: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:10:52.82: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:53.50: [ 1723]: --> [2:OK]
Jan 02 13:10:53.50: [ 1723]: REMOTE CSI "3065854815"
Jan 02 13:10:53.50: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:10:53.51: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:53.77: [ 1723]: --> [2:OK]
Jan 02 13:10:53.77: [ 1723]: REMOTE best rate 9600 bit/s
Jan 02 13:10:53.77: [ 1723]: REMOTE max page width 1728 pixels in 215 mm
Jan 02 13:10:53.77: [ 1723]: REMOTE max unlimited page length 
Jan 02 13:10:53.77: [ 1723]: REMOTE best vres 7.7 line/mm
Jan 02 13:10:53.77: [ 1723]: REMOTE best format 2-D MR
Jan 02 13:10:53.77: [ 1723]: REMOTE best 10 ms, 5 ms/scanline
Jan 02 13:10:53.77: [ 1723]: USE 9600 bit/s
Jan 02 13:10:53.77: [ 1723]: USE 10 ms, 5 ms/scanline
Jan 02 13:10:53.77: [ 1723]: SEND file "docq/doc5.cover;70"
Jan 02 13:10:53.77: [ 1723]: USE page width 1728 pixels in 215 mm
Jan 02 13:10:53.77: [ 1723]: USE unlimited page length 
Jan 02 13:10:53.77: [ 1723]: USE 3.85 line/mm
Jan 02 13:10:53.77: [ 1723]: USE 1-D MR
Jan 02 13:10:53.77: [ 1723]: SEND training at v.29 9600 bit/s
Jan 02 13:10:53.77: [ 1723]: <-- [9:AT+FTH=3\r]
Jan 02 13:10:54.01: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:54.01: [ 1723]: <-- data [23]
Jan 02 13:10:54.01: [ 1723]: <-- data [2]
Jan 02 13:10:54.03: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:54.03: [ 1723]: <-- data [6]
Jan 02 13:10:54.03: [ 1723]: <-- data [2]
Jan 02 13:10:55.98: [ 1723]: --> [2:OK]
Jan 02 13:10:55.98: [ 1723]: DELAY 75 ms
Jan 02 13:10:56.07: [ 1723]: <-- [10:AT+FTM=96\r]
Jan 02 13:10:56.39: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:56.39: [ 1723]: <-- data [1024]
Jan 02 13:10:56.39: [ 1723]: <-- data [776]
Jan 02 13:10:56.39: [ 1723]: <-- data [2]
Jan 02 13:10:57.92: [ 1723]: --> [2:OK]
Jan 02 13:10:57.92: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:10:58.30: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:59.36: [ 1723]: --> [2:OK]
Jan 02 13:10:59.36: [ 1723]: TRAINING succeeded
Jan 02 13:10:59.36: [ 1723]: <-- [10:AT+FTM=96\r]
Jan 02 13:10:59.79: [ 1723]: --> [7:CONNECT]
Jan 02 13:10:59.79: [ 1723]: SEND begin page
Jan 02 13:10:59.80: [ 1723]: <-- data [1028]
Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
Jan 02 13:10:59.80: [ 1723]: <-- data [1024]
Jan 02 13:10:59.80: [ 1723]: <-- data [1027]
Jan 02 13:11:00.80: [ 1723]: <-- data [1024]
Jan 02 13:11:00.80: [ 1723]: <-- data [1026]
Jan 02 13:11:00.80: [ 1723]: <-- data [1024]
Jan 02 13:11:01.82: [ 1723]: <-- data [1027]
Jan 02 13:11:02.87: [ 1723]: <-- data [1026]
Jan 02 13:11:03.92: [ 1723]: <-- data [1030]
Jan 02 13:11:03.92: [ 1723]: <-- data [1024]
Jan 02 13:11:04.97: [ 1723]: <-- data [630]
Jan 02 13:11:06.07: [ 1723]: SENT 12917 bytes of data
Jan 02 13:11:06.08: [ 1723]: <-- data [1027]
Jan 02 13:11:06.08: [ 1723]: <-- data [1024]
Jan 02 13:11:07.12: [ 1723]: <-- data [1024]
Jan 02 13:11:08.17: [ 1723]: <-- data [532]
Jan 02 13:11:08.20: [ 1723]: SENT 3604 bytes of data
Jan 02 13:11:08.20: [ 1723]: SEND 1D RTC
Jan 02 13:11:08.20: [ 1723]: <-- data [29]
Jan 02 13:11:08.20: [ 1723]: <-- data [2]
Jan 02 13:11:08.20: [ 1723]: SEND end page
Jan 02 13:11:13.62: [ 1723]: --> [2:OK]
Jan 02 13:11:13.62: [ 1723]: DELAY 75 ms
Jan 02 13:11:13.71: [ 1723]: SEND send MPS (more pages, same document)
Jan 02 13:11:13.71: [ 1723]: <-- [9:AT+FTH=3\r]
Jan 02 13:11:13.86: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:13.86: [ 1723]: <-- data [3]
Jan 02 13:11:13.86: [ 1723]: <-- data [2]
Jan 02 13:11:15.04: [ 1723]: --> [2:OK]
Jan 02 13:11:15.04: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:11:18.14: [ 1723]: --> [0:]
Jan 02 13:11:18.15: [ 1723]: MODEM <Empty line>
Jan 02 13:11:18.15: [ 1723]: <-- data [1]
Jan 02 13:11:18.17: [ 1723]: --> [2:OK]
Jan 02 13:11:18.17: [ 1723]: SEND send MPS (more pages, same document)
Jan 02 13:11:18.17: [ 1723]: <-- [9:AT+FTH=3\r]
Jan 02 13:11:18.20: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:18.20: [ 1723]: <-- data [3]
Jan 02 13:11:18.20: [ 1723]: <-- data [2]
Jan 02 13:11:19.38: [ 1723]: --> [2:OK]
Jan 02 13:11:19.38: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:11:19.90: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:20.85: [ 1723]: --> [2:OK]
Jan 02 13:11:20.85: [ 1723]: SEND recv MCF (message confirmation)
Jan 02 13:11:20.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (page 1 of 2 sent in 0:27)
Jan 02 13:11:20.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (docq/doc5.cover;70 sent in 0:27)
Jan 02 13:11:20.85: [ 1723]: SEND file "docq/doc9.ps;70"
Jan 02 13:11:20.85: [ 1723]: USE page width 1728 pixels in 215 mm
Jan 02 13:11:20.86: [ 1723]: USE unlimited page length 
Jan 02 13:11:20.86: [ 1723]: USE 3.85 line/mm
Jan 02 13:11:20.86: [ 1723]: USE 1-D MR
Jan 02 13:11:20.86: [ 1723]: <-- [10:AT+FTM=96\r]
Jan 02 13:11:21.29: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:21.29: [ 1723]: SEND begin page
Jan 02 13:11:21.30: [ 1723]: <-- data [1029]
Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
Jan 02 13:11:21.30: [ 1723]: <-- data [1024]
Jan 02 13:11:21.30: [ 1723]: <-- data [1025]
Jan 02 13:11:22.30: [ 1723]: <-- data [1027]
Jan 02 13:11:22.30: [ 1723]: <-- data [1025]
Jan 02 13:11:22.30: [ 1723]: <-- data [1025]
Jan 02 13:11:23.27: [ 1723]: <-- data [1025]
Jan 02 13:11:24.32: [ 1723]: <-- data [1026]
Jan 02 13:11:25.42: [ 1723]: <-- data [1024]
Jan 02 13:11:25.42: [ 1723]: <-- data [228]
Jan 02 13:11:26.52: [ 1723]: SENT 11492 bytes of data
Jan 02 13:11:26.52: [ 1723]: SEND 1D RTC
Jan 02 13:11:26.52: [ 1723]: <-- data [29]
Jan 02 13:11:26.52: [ 1723]: <-- data [2]
Jan 02 13:11:26.52: [ 1723]: SEND end page
Jan 02 13:11:30.93: [ 1723]: --> [2:OK]
Jan 02 13:11:30.95: [ 1723]: DELAY 95 ms
Jan 02 13:11:31.06: [ 1723]: SEND send EOP (no more pages or documents)
Jan 02 13:11:31.06: [ 1723]: <-- [9:AT+FTH=3\r]
Jan 02 13:11:31.21: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:31.21: [ 1723]: <-- data [3]
Jan 02 13:11:31.21: [ 1723]: <-- data [2]
Jan 02 13:11:32.39: [ 1723]: --> [2:OK]
Jan 02 13:11:32.39: [ 1723]: <-- [9:AT+FRH=3\r]
Jan 02 13:11:33.05: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:33.85: [ 1723]: --> [2:OK]
Jan 02 13:11:33.85: [ 1723]: SEND recv MCF (message confirmation)
Jan 02 13:11:33.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (page 2 of 2 sent in 0:13)
Jan 02 13:11:33.85: [ 1723]: SEND FAX (00000008): FROM nicolc@dora.econ.uregina.ca TO 585-4815 (docq/doc9.ps;70 sent in 0:13)
Jan 02 13:11:33.85: [ 1723]: <-- [9:AT+FTH=3\r]
Jan 02 13:11:34.09: [ 1723]: --> [7:CONNECT]
Jan 02 13:11:34.09: [ 1723]: <-- data [3]
Jan 02 13:11:34.09: [ 1723]: <-- data [2]
Jan 02 13:11:35.26: [ 1723]: --> [2:OK]
Jan 02 13:11:35.26: [ 1723]: <-- [5:ATH0\r]
Jan 02 13:11:35.49: [ 1723]: --> [2:OK]
Jan 02 13:11:35.49: [ 1723]: SESSION END


Thanks for any help.

Chris Nicol.

(PS: Never had this problem with v 3.0pl1. CN)
_______________________________________________________________________________
Dr. Chris Nicol, Economics     Phone:  (306) 585-4182; FAX: 585-4815
University of Regina           E-Mail: nicolc@elsie.econ.uregina.ca
Saskatchewan, S4S 0A2, CANADA.         nicolc@cas.uregina.ca