Personal tools
HylaFAX The world's most advanced open source fax server

Class1 config

Revision as of 14:56, 20 December 2005 by Darren (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
# $Id: class1,v 1.2 2000/09/04 18:53:45 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

# CONFIG:CLASS1:"ATI0":"ATI3":flowcontrol: Manufacturer='name' Model='name'
#
# BEGIN-SERVER
# END-SERVER
#

ModemAnswerCmd:			ATA	# string, command for answering phone
ModemAnswerDataBeginCmd:	""	# string, command for start of answered data call
ModemAnswerDataCmd:		ATA	# string, command for answering data call
ModemAnswerFaxBeginCmd:		""	# string, command for start of answered fax call
ModemAnswerFaxCmd:		ATA	# string, command for answering fax call
ModemAnswerResponseTimeout:	180000	# integer, answer command timeout (ms)
ModemAnswerVoiceBeginCmd:	""	# string, command for start of answered voice call
ModemAnswerVoiceCmd:		ATA	# string, command for answering voice call
ModemATCmdDelay:		0	# integer, delay before sending modem an AT cmd (ms)
ModemBaudRateDelay:		0	# integer, delay (ms) after setting baud rate
ModemClassQueryCmd:		AT+FCLASS=?	# string, command for querying modem services
ModemCommaPauseTimeCmd:		ATS8=2	# string, command for setting time to pause for comma in dialing string
ModemDialCmd:			ATDT%s	# string, command for dialing (%s for number to dial)
ModemDialResponseTimeout:	180000	# integer, dialing command timeout (ms)
ModemEchoOffCmd:		ATE0	# string, command for disabling command echo
ModemFlowControl:		None	# string, DTE-DCE flow control scheme
ModemFrameFillOrder:		LSB2MSB	# string, bit order for HDLC frames
ModemHardFlowCmd:		""	# string, command for setting hardware flow control between DTE and DCE
ModemMinSpeed:			2400	# string, minimum acceptable transmit speed
ModemMfrQueryCmd:		""	# string, command for querying modem manufacturer
ModemModelQueryCmd:		""	# string, command for querying modem model
ModemNoAutoAnswerCmd:		ATS0=0	# string, command for disabling auto-answer
ModemNoFlowCmd:			""	# string, command for disabling hardware flow control between DTE and DCE
ModemOnHookCmd:			ATH0	# string, command for placing phone ``on hook''
ModemPageDoneTimeout:		180000	# integer, page send/receive timeout (ms)
ModemPageStartTimeout:		180000	# integer, page send/receive timeout (ms)
ModemRate:			19200	# integer, baud rate to use for DCE-DTE communication
ModemRecvFillOrder:		LSB2MSB	# string, bit order for received facsimile data
ModemResetCmds:			""	# string, additional commands when resetting modem
ModemResetDelay:		2600	# integer, delay (ms) after sending modem reset commands
ModemResultCodesCmd:		ATQ0	# string, command for enabling result codes
ModemRevQueryCmd:		""	# string, command for querying modem firmware revision
ModemSendBeginCmd:		""	# string, command to send on establishing carrier
ModemSendFillOrder:		LSB2MSB	# string, bit order for sending facsimile data
ModemSetVolumeCmd:		"ATM0 ATL0M1 ATL8C1 ATL2M1 ATL3M1"	# string, commands for setting modem speaker volume level
ModemSetupAACmd:		""	# string, command for setting up adaptive answer
ModemSetupDCDCmd:		""	# string, command for setting up DCD handling
ModemSetupDTRCmd:		""	# string, command for setting up DTR handling
ModemSoftFlowCmd:		""	# string, command for setting software flow control between DTE and DCE
ModemSoftResetCmd:		ATZ	# string, command for doing a soft reset
ModemType:			Class1	# string, modem type
ModemVerboseResultsCmd:		ATV1	# string, command for enabling verbose result codes
ModemWaitForConnect:		No	# boolean, force server to wait for ``CONNECT'' response on answer
ModemWaitTimeCmd:		ATS7=60	# string, command for setting time to wait for carrier when dialing

Class1Cmd:			AT+FCLASS=1	# string, command to enter class 1
Class1HFLOCmd:			""	# string, command to set hardware flow control
Class1FrameOverhead:		4	# integer, extra bytes in a received HDLC frame
Class1NFLOCmd:			""	# string, command to set no flow control
Class1RecvAbortOK:		100	# integer, max wait (ms) for ``OK'' after recv abort
Class1RecvIdentTimer:		35000	# integer, max wait (ms) for initial ident frame
Class1SFLOCmd:			""	# string, command to set software flow control
Class1TCFMaxNonZero:		10	# integer, max% of non-zero data in good TCF
Class1TCFMinRun:		1000	# integer, minimum zero run in good TCF
Class1TCFRecvTimeout:		4500	# integer, max wait (ms) for TCF
Class1TCFResponseDelay:		75	# integer, delay between TCF and ack/nak
Class1SendPPMDelay:		75	# integer, delay before sending post-page message
Class1SendTCFDelay:		75	# integer, delay between sending DCS and TCF
Class1TrainingRecovery:		1500	# integer, delay after failed training


This page was last edited on 20 December 2005, at 14:56.

Powered by MediaWiki
Attribution-ShareAlike 2.5

Project hosted by iFAX Solutions