[hylafax-users] receiving incomplete fax

[voipas <voipas@xxxxxxxxx>]

Hi,

 

  I'm receiving incomplete faxes from one number: TDM->VoiP->Hylafax . IAXmodem's version is 1.2.0 .  

 

Here is hylafax log:

 

Sep 28 08:57:07.86: [ 2003]: SESSION BEGIN 000081083 46266464
Sep 28 08:57:07.86: [ 2003]: HylaFAX (tm) Version 5.4.1
Sep 28 08:57:07.86: [ 2003]: CallID: '11111111111' '' '<NONE>' '22222222222'
Sep 28 08:57:07.86: [ 2003]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Sep 28 08:57:07.86: [ 2003]: <-- [4:ATA\r]
Sep 28 08:57:11.58: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:11.58: [ 2003]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyIAX4'
Sep 28 08:57:11.58: [ 2003]: STATE CHANGE: ANSWERING -> RECEIVING
Sep 28 08:57:11.58: [ 2003]: RECV FAX: begin
Sep 28 08:57:11.58: [ 2003]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 AC 74 2C 74 8C>
Sep 28 08:57:11.58: [ 2003]: <-- data [32]
Sep 28 08:57:11.58: [ 2003]: <-- data [2]
Sep 28 08:57:12.54: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:12.54: [ 2003]: <-- HDLC<23:FF C0 02 4E A6 6E 4E A6 CA 1E 86 62 04 04 04 04 04 04 04 04 04 04 04>
Sep 28 08:57:12.54: [ 2003]: <-- data [23]
Sep 28 08:57:12.54: [ 2003]: <-- data [2]
Sep 28 08:57:13.28: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:13.28: [ 2003]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Sep 28 08:57:13.28: [ 2003]: <-- data [13]
Sep 28 08:57:13.28: [ 2003]: <-- data [2]
Sep 28 08:57:13.86: [ 2003]: --> [2:OK]
Sep 28 08:57:13.86: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:57:14.42: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:16.02: [ 2003]: --> HDLC<25:FF C0 C2 6C 4C 1C 8C 6C 9C 1C CC 0C EC CC 04 04 04 04 04 04 04 04 04 57 4D>
Sep 28 08:57:16.02: [ 2003]: --> [2:OK]
Sep 28 08:57:16.02: [ 2003]: RECV recv TSI (sender id)
Sep 28 08:57:16.02: [ 2003]: REMOTE TSI "11111111111"
Sep 28 08:57:16.02: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:57:16.29: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:16.29: [ 2003]: --> HDLC<9:FF C8 C1 00 60 11 00 2A F2>
Sep 28 08:57:16.35: [ 2003]: --> [2:OK]
Sep 28 08:57:16.35: [ 2003]: RECV recv DCS (command signal)
Sep 28 08:57:16.36: [ 2003]: REMOTE wants 9600 bit/s
Sep 28 08:57:16.36: [ 2003]: REMOTE wants A4 page width (215 mm)
Sep 28 08:57:16.36: [ 2003]: REMOTE wants unlimited page length
Sep 28 08:57:16.36: [ 2003]: REMOTE wants 3.85 line/mm
Sep 28 08:57:16.36: [ 2003]: REMOTE wants 1-D MH
Sep 28 08:57:16.36: [ 2003]: RECV training at v.29 9600 bit/s
Sep 28 08:57:16.36: [ 2003]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Sep 28 08:57:16.36: [ 2003]: <-- [10:AT+FRM=96\r]
Sep 28 08:57:16.66: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:16.76: [ 2003]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Sep 28 08:57:16.76: [ 2003]: RECV: TCF 127 bytes, 17% non-zero, 105 zero-run
Sep 28 08:57:16.76: [ 2003]: RECV: reject TCF (too many non-zero, max 10%)
Sep 28 08:57:16.76: [ 2003]: RECV: reject TCF (zero run too short, min 1200)
Sep 28 08:57:16.76: [ 2003]: --> [10:NO CARRIER]
Sep 28 08:57:16.76: [ 2003]: <-- [9:AT+FRS=7\r]
Sep 28 08:57:16.82: [ 2003]: --> [2:OK]
Sep 28 08:57:16.82: [ 2003]: <-- [9:AT+FTH=3\r]
Sep 28 08:57:16.83: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:16.83: [ 2003]: <-- HDLC<3:FF C8 22>
Sep 28 08:57:16.83: [ 2003]: <-- data [3]
Sep 28 08:57:16.84: [ 2003]: <-- data [2]
Sep 28 08:57:17.90: [ 2003]: --> [2:OK]
Sep 28 08:57:17.90: [ 2003]: TRAINING failed
Sep 28 08:57:17.90: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:57:21.36: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:22.96: [ 2003]: --> HDLC<25:FF C0 C2 6C 4C 1C 8C 6C 9C 1C CC 0C EC CC 04 04 04 04 04 04 04 04 04 57 4D>
Sep 28 08:57:22.96: [ 2003]: --> [2:OK]
Sep 28 08:57:22.96: [ 2003]: RECV recv TSI (sender id)
Sep 28 08:57:22.96: [ 2003]: REMOTE TSI "11111111111"
Sep 28 08:57:22.96: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:57:23.24: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:23.24: [ 2003]: --> HDLC<9:FF C8 C1 00 60 11 00 2A F2>
Sep 28 08:57:23.30: [ 2003]: --> [2:OK]
Sep 28 08:57:23.30: [ 2003]: RECV recv DCS (command signal)
Sep 28 08:57:23.30: [ 2003]: REMOTE wants 9600 bit/s
Sep 28 08:57:23.30: [ 2003]: REMOTE wants A4 page width (215 mm)
Sep 28 08:57:23.30: [ 2003]: REMOTE wants unlimited page length
Sep 28 08:57:23.30: [ 2003]: REMOTE wants 3.85 line/mm
Sep 28 08:57:23.30: [ 2003]: REMOTE wants 1-D MH
Sep 28 08:57:23.30: [ 2003]: RECV training at v.29 9600 bit/s
Sep 28 08:57:23.30: [ 2003]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Sep 28 08:57:23.30: [ 2003]: <-- [10:AT+FRM=96\r]
Sep 28 08:57:23.60: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:25.12: [ 2003]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Sep 28 08:57:25.12: [ 2003]: RECV: TCF 1825 bytes, 1% non-zero, 1800 zero-run
Sep 28 08:57:25.12: [ 2003]: --> [10:NO CARRIER]
Sep 28 08:57:25.12: [ 2003]: <-- [9:AT+FRS=7\r]
Sep 28 08:57:25.18: [ 2003]: --> [2:OK]
Sep 28 08:57:25.18: [ 2003]: TRAINING succeeded
Sep 28 08:57:25.18: [ 2003]: <-- [9:AT+FTH=3\r]
Sep 28 08:57:25.19: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:25.19: [ 2003]: <-- HDLC<3:FF C8 21>
Sep 28 08:57:25.19: [ 2003]: <-- data [3]
Sep 28 08:57:25.19: [ 2003]: <-- data [2]
Sep 28 08:57:26.26: [ 2003]: --> [2:OK]
Sep 28 08:57:26.26: [ 2003]: <-- [10:AT+FRM=96\r]
Sep 28 08:57:26.90: [ 2003]: --> [7:CONNECT]
Sep 28 08:57:26.90: [ 2003]: MODEM input buffering enabled
Sep 28 08:57:26.90: [ 2003]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Sep 28 08:57:26.90: [ 2003]: RECV: begin page
Sep 28 08:57:33.72: [ 2003]: RECV/CQ: Invalid WhiteTable code word, row 232, x 362
Sep 28 08:57:33.72: [ 2003]: RECV/CQ: Bad 1D pixel count, row 232, got 362, expected 1728
Sep 28 08:57:33.72: [ 2003]: RECV/CQ: Adjusting for trailing noise (1 run)
Sep 28 08:57:33.72: [ 2003]: RECV: 232 total lines, 0 bad lines, 1 consecutive bad lines
Sep 28 08:57:33.72: [ 2003]: RECV: end page
Sep 28 08:57:33.72: [ 2003]: --> [10:NO CARRIER]
Sep 28 08:57:33.72: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:58:03.20: [ 2003]: --> [7:CONNECT]
Sep 28 08:58:04.34: [ 2003]: --> HDLC<5:FF C8 F4 CC 66>
Sep 28 08:58:04.34: [ 2003]: --> [2:OK]
Sep 28 08:58:04.34: [ 2003]: RECV recv EOP (no more pages or documents)
Sep 28 08:58:04.34: [ 2003]: <-- [9:AT+FRS=7\r]
Sep 28 08:58:04.44: [ 2003]: --> [2:OK]
Sep 28 08:58:04.44: [ 2003]: RECV send MCF (message confirmation)
Sep 28 08:58:04.44: [ 2003]: <-- [9:AT+FTH=3\r]
Sep 28 08:58:04.55: [ 2003]: --> [7:CONNECT]
Sep 28 08:58:04.55: [ 2003]: <-- HDLC<3:FF C8 31>
Sep 28 08:58:04.55: [ 2003]: <-- data [3]
Sep 28 08:58:04.55: [ 2003]: <-- data [2]
Sep 28 08:58:05.62: [ 2003]: --> [2:OK]
Sep 28 08:58:05.62: [ 2003]: <-- [9:AT+FRH=3\r]
Sep 28 08:58:06.16: [ 2003]: --> [7:CONNECT]
Sep 28 08:58:07.29: [ 2003]: --> HDLC<5:FF C8 DF 59 6F>
Sep 28 08:58:07.30: [ 2003]: --> [2:OK]
Sep 28 08:58:07.30: [ 2003]: RECV recv DCN (disconnect)
Sep 28 08:58:07.30: [ 2003]: RECV FAX (000081083): from 11111111111, page 1 in 0:00:22, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
Sep 28 08:58:08.30: [ 2003]: RECV FAX (000081083): recvq/fax000058403.tif from 11111111111, subaddress <unspecified>, 1 pages in 0:00:56
Sep 28 08:58:08.30: [ 2003]: RECV FAX: bin/faxrcvd 'recvq/fax000058403.tif' 'ttyIAX4' '000081083' '' '11111111111' '' '<NONE>' '22222222222'
Sep 28 08:58:08.31: [ 2003]: RECV FAX: end
Sep 28 08:58:08.31: [ 2003]: SESSION END

  Could you please help me to solve the problem.
--
Best Regards,
Giedrius