[hylafax-users] Missing EOL after 5 seconds

[Davide Cirillo <david.gnome85@xxxxxxxxx>]

Hi all i'm new,

i've used hylafax + whfc for 1-2 years, now i've a problem with an HP Proliant with a CLASS1 Trust modem (serial of corse), when i receive faxes that have 2 or more pages i receive a Missing EOL after 5 seconds and i receive only 1 page. Only 1 time i've received 2 pages of 3 and only 1 time i've received 2 of 2 but there was only a line in each pages hello world for example.

Here is 1 of my logs:

Mar 10 15:23:19.64: [ 5688]: SESSION BEGIN 000000063 390669940648
Mar 10 15:23:19.64: [ 5688]: HylaFAX (tm) Version 4.4.3
Mar 10 15:23:19.65: [ 5688]: <-- [4:ATA\r]
Mar 10 15:23:27.97: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:27.97: [ 5688]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Mar 10 15:23:27.97: [ 5688]: RECV FAX: begin
Mar 10 15:23:27.97: [ 5688]: <-- data [32]
Mar 10 15:23:27.97: [ 5688]: <-- data [2]
Mar 10 15:23:28.00: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:28.00: [ 5688]: <-- data [23]
Mar 10 15:23:28.00: [ 5688]: <-- data [2]
Mar 10 15:23:28.03: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:28.03: [ 5688]: <-- data [13]
Mar 10 15:23:28.03: [ 5688]: <-- data [2]
Mar 10 15:23:31.23: [ 5688]: --> [2:OK]
Mar 10 15:23:31.23: [ 5688]: <-- [9:AT+FRH=3\r]
Mar 10 15:23:31.68: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:33.10: [ 5688]: --> [2:OK]
Mar 10 15:23:33.10: [ 5688]: REMOTE TSI ""
Mar 10 15:23:33.10: [ 5688]: RECV recv TSI (sender id)
Mar 10 15:23:33.10: [ 5688]: <-- [9:AT+FRH=3\r]
Mar 10 15:23:33.12: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:33.43: [ 5688]: --> [2:OK]
Mar 10 15:23:33.43: [ 5688]: REMOTE wants 14400 bit/s
Mar 10 15:23:33.43: [ 5688]: REMOTE wants A4 page width (215 mm)
Mar 10 15:23:33.43: [ 5688]: REMOTE wants unlimited page length
Mar 10 15:23:33.43: [ 5688]: REMOTE wants 3.85 line/mm
Mar 10 15:23:33.43: [ 5688]: REMOTE wants 2-D MR
Mar 10 15:23:33.43: [ 5688]: RECV recv DCS (command signal)
Mar 10 15:23:33.43: [ 5688]: RECV training at v.17 14400 bit/s
Mar 10 15:23:33.43: [ 5688]: <-- [11:AT+FRM=145\r]
Mar 10 15:23:34.98: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:36.75: [ 5688]: RECV: TCF 2520 bytes, 0% non-zero, 2520 zero-run
Mar 10 15:23:36.76: [ 5688]: --> [10:NO CARRIER]
Mar 10 15:23:36.76: [ 5688]: DELAY 70 ms
Mar 10 15:23:36.83: [ 5688]: TRAINING succeeded
Mar 10 15:23:36.85: [ 5688]: <-- [9:AT+FTH=3\r]
Mar 10 15:23:36.90: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:36.90: [ 5688]: <-- data [3]
Mar 10 15:23:36.90: [ 5688]: <-- data [2]
Mar 10 15:23:38.22: [ 5688]: --> [2:OK]
Mar 10 15:23:38.22: [ 5688]: <-- [11:AT+FRM=146\r]
Mar 10 15:23:38.92: [ 5688]: --> [7:CONNECT]
Mar 10 15:23:38.92: [ 5688]: RECV: begin page
Mar 10 15:24:04.79: [ 5688]: RECV: 1146 total lines, 0 bad lines, 0 consecutive bad lines
Mar 10 15:24:04.79: [ 5688]: RECV: end page
Mar 10 15:24:04.79: [ 5688]: --> [10:NO CARRIER]
Mar 10 15:24:04.79: [ 5688]: <-- [9:AT+FRH=3\r]
Mar 10 15:24:05.06: [ 5688]: --> [7:CONNECT]
Mar 10 15:24:05.96: [ 5688]: --> [2:OK]
Mar 10 15:24:05.96: [ 5688]: RECV recv MPS (more pages, same document)
Mar 10 15:24:05.96: [ 5688]: DELAY 70 ms
Mar 10 15:24:06.03: [ 5688]: <-- [9:AT+FTH=3\r]
Mar 10 15:24:06.18: [ 5688]: --> [7:CONNECT]
Mar 10 15:24:06.18: [ 5688]: RECV send MCF (message confirmation)
Mar 10 15:24:06.18: [ 5688]: RECV FAX (000000063): from , page 1 in 0:37, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Mar 10 15:24:06.18: [ 5688]: <-- data [3]
Mar 10 15:24:06.18: [ 5688]: <-- data [2]
Mar 10 15:24:07.50: [ 5688]: --> [2:OK]
Mar 10 15:24:07.50: [ 5688]: <-- [11:AT+FRM=146\r]
Mar 10 15:24:08.16: [ 5688]: --> [7:CONNECT]
Mar 10 15:24:08.16: [ 5688]: RECV: begin page
Mar 10 15:25:15.41: [ 5688]: <-- data [1]
Mar 10 15:25:15.41: [ 5688]: RECV: Missing EOL after 5 seconds
Mar 10 15:25:15.41: [ 5688]: RECV: end page
Mar 10 15:25:20.41: [ 5688]: MODEM <Timeout>
Mar 10 15:25:20.41: [ 5688]: <-- data [1]
Mar 10 15:25:20.61: [ 5688]: MODEM <Timeout>
Mar 10 15:25:20.61: [ 5688]: RECV keeping unconfirmed page
Mar 10 15:25:20.61: [ 5688]: RECV FAX (000000063): from , page 2 in 0:37, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Mar 10 15:25:20.61: [ 5688]: RECV FAX (000000063): recvq/fax000000029.tif from , route to <unspecified>, 2 pages in 1:53
Mar 10 15:25:20.61: [ 5688]: RECV FAX: T.30 T2 timeout, expected page not received
Mar 10 15:25:20.61: [ 5688]: <-- [9:AT+FTH=3\r]
Mar 10 15:25:28.16: [ 5688]: --> [0:]
Mar 10 15:25:28.16: [ 5688]: RECV FAX (000000063): session with  terminated abnormally: T.30 T2 timeout, expected page not received
Mar 10 15:25:28.16: [ 5688]: RECV FAX: bin/faxrcvd "recvq/fax000000029.tif" "ttyS0" "000000063" "T.30 T2 timeout, expected page not received"
Mar 10 15:25:28.16: [ 5688]: RECV FAX: end
Mar 10 15:25:28.16: [ 5688]: T.30 T2 timeout, expected page not received
Mar 10 15:25:28.16: [ 5688]: SESSION END

here is my config:

# $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $
#
# prototype config for Topic modems and other similarly broken firmwares
#

#
CountryCode:            39
AreaCode:               06
FAXNumber:              69940648
LongDistancePrefix:     0
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0777
LogFileMode:            0600
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Mare Neve Srl Fax
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#

ModemType:              Class1          # use this to supply a hint

# as of v1.20, +FTS is not supported, which will cause "Stop and wait"
# failures unless we use software pauses instead...

Class1PPMWaitCmd:       "<delay\0727>"  # \072 == :  to avoid awk problem
Class1TCFWaitCmd:       "<delay\0727>"
Class1EOPWaitCmd:       "<delay\0729>"
Class1SwitchingCmd:     "<delay\0727>"  # assumption: +FRS not supported

Class2RecvDataTrigger: "\022" # Is a try

ModemResultCodesCmd:    ATQ0X3
ModemDialCmd:           ATX3DT%s


thanks

Davide.