[hylafax-users] MODEM <Timeout> on Multitech

[Lorenzo Milesi <lorenzo.milesi@xxxxxxxxxx>]

Hi.

I recently installed a faxserver with two modems: an unknown one and a Multitech MT5656ZDX. 
The first is working great, the second one not always. I have this modem on another server working 100%.
The only difference is that now it's attached using a PL2303 usb<->serial converter.
I tried on my laptop with the very same converter and I could send a fax without problems, using efax.
Both modems are attached using similar (not same) converter, but all with pl2303 chip.

Now, on the server, with Hyla 4.4.3, the MT is initialized only sometimes. And even if it initializes, when it receives a fax it then goes wrong again.

This is the log of ServerTracing 8 on the ttyUSB1 modem. What could make it go wrong?

FaxQueuer[17026]: HylaFAX (tm) Version 4.4.3
FaxQueuer[17026]: Copyright (c) 1990-1996 Sam Leffler
FaxQueuer[17026]: Copyright (c) 1991-1996 Silicon Graphics, Inc.
HylaFAX[17028]: HylaFAX INET Protocol Server: restarted.
FaxGetty[17042]: OPEN /dev/ttyUSB0  HylaFAX (tm) Version 4.4.3
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17042]: MODEM AGERE VENUS V.92 SERIAL S071101 VOICE V2 V92CAP 12NS RAM MERCURY Agere Venus V.92 Serial s071101 Voice V2 V92cap 12ns RAM Mercury/
FaxGetty[17046]: MODEM <Timeout>
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [3:ATZ]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17046]: --> [6:ATS0=0]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [5:ATE0\r]
FaxGetty[17046]: --> [4:ATE0]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [5:ATV1\r]
FaxGetty[17046]: MODEM <Timeout>
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17046]: MODEM <Timeout>
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [3:ATZ]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17046]: MODEM <Timeout>
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [3:ATZ]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17046]: MODEM <Timeout>
FaxGetty[17046]: <-- [4:ATZ\r]
FaxGetty[17046]: --> [3:ATZ]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [7:ATS0=0\r]
FaxGetty[17046]: --> [6:ATS0=0]
FaxGetty[17046]: --> [2:OK]
FaxGetty[17046]: <-- [5:ATE0\r]
FaxGetty[17046]: MODEM <Timeout>
FaxQueuer[17026]: MODEM /dev/ttyUSB1 appears to be wedged
FaxQueuer[17026]: MODEM WEDGED: bin/wedged "ttyUSB1" "/dev/ttyUSB1"
FaxQueuer[17026]: NOTIFY exit status: 0 (19504)


This is the config:
CountryCode:		39
AreaCode:		033
FAXNumber:		+3903333333
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	""
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
NotifyCmd:		bin/notify.php
FaxrcvdCmd:             bin/faxrcvd.php
DynamicConfig:          bin/dynconf.php
ModemType:		Class1		# use this to supply a hint
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait before PPM
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait before TCF
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait before EOP
Class1SwitchingCmd:	AT+FRS=7	# silence between HDLC recv and trans
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration
Class1TMQueryCmd: "!3,24,48,72,73,74,96,97,98,121,122,145,146"
Class1RMQueryCmd: "!3,24,48,72,73,74,96,97,98,121,122,145,146"
ServerTracing: 8


Any ideas?
thanks

-- 
Lorenzo Milesi - lorenzo.milesi@xxxxxxxxxx

YetOpen S.r.l. - http://www.yetopen.it/
Via Previati 72 - 23900 Lecco - ITALY -
Tel 0341 220 205 - Fax 178 6070 222

GPG/PGP Key-Id: 0xE704E230 - http://keyserver.linux.it

-------- D.Lgs. 196/2003 --------

Si avverte che tutte le informazioni contenute in questo messaggio sono
riservate ed a uso esclusivo del destinatario. Nel caso in cui questo
messaggio Le fosse pervenuto per errore, La invitiamo ad eliminarlo
senza copiarlo, a non inoltrarlo a terzi e ad avvertirci non appena
possibile.
Grazie.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*