 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Modem Timeout
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Modem Timeout
- From: Alessio Fattorini <alessio.fattorini@xxxxxxxxxxx>
- Date: Fri, 06 Feb 2009 15:09:45 +0100
Hi,
my modem is:
MODEM AGERE OCM V.92 VER2.7A (JUN 14 2004) VOICE MERCURY DP2SH MODE-II SERIAL Agere OCM V.92 Ver2.7a (Jun 14 2004) Voice Mercury DP2SH mode-ii SERIAL/
Hylafax: hylafax-4.3.7-1.1nh.rhel4
On RHEL 4.6
I have problem with some fax, and errors are:
RECV FAX (000001488): session with ++39 02 6*** terminated abnormally: T.30 T2 timeout, expected page not received
RECV FAX (000001495): session with 0382 *** terminated abnormally: COMREC received DCN
Feb 2 12:38:16 server03 FaxGetty[4245]: RECV FAX (000001508): session with 0382 931235 terminated abnormally: Failed to properly detect high-speed data carrier.
RECV FAX (000001520): session with Te***** terminated abnormally: Failed to properly detect high-speed data carrier.
RECV FAX (000001596): session with BARD*** terminated abnormally: T.30 T2 timeout, expected page not received
Con you help me?? Mo --------- My config.ttyS0
DialStringRules: etc/dialrules ServerTracing: 1 #SessionTracing: 11 SessionTracing: 0xFFF RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: on GettyArgs: "-h %l dx_%s" LocalIdentifier: "Senna Inox S.r.L" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 FaxRcvdCmd: bin/faxrcvd.faxweb NotifyCmd: bin/notify.faxweb
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
------------- One log in debug mode:
Feb 06 12:44:02.08: [ 2893]: SESSION BEGIN 000001596 39371*****
Feb 06 12:44:02.08: [ 2893]: HylaFAX (tm) Version 4.3.7
Feb 06 12:44:02.08: [ 2893]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Feb 06 12:44:02.08: [ 2893]: <-- [4:ATA\r]
Feb 06 12:44:12.05: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:12.05: [ 2893]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Feb 06 12:44:12.05: [ 2893]: STATE CHANGE: ANSWERING -> RECEIVING
Feb 06 12:44:12.05: [ 2893]: RECV FAX: begin
Feb 06 12:44:12.07: [ 2893]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 CC 74 EC>
Feb 06 12:44:12.07: [ 2893]: <-- data [32]
Feb 06 12:44:12.07: [ 2893]: <-- data [2]
Feb 06 12:44:12.10: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:12.10: [ 2893]: <-- HDLC<23:FF C0 02 32 74 4E 74 CA 04 1E F6 76 92 04 86 76 76 A6 CA 04 04 04 04>
Feb 06 12:44:12.10: [ 2893]: <-- data [23]
Feb 06 12:44:12.10: [ 2893]: <-- data [2]
Feb 06 12:44:12.12: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:12.12: [ 2893]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Feb 06 12:44:12.12: [ 2893]: <-- data [13]
Feb 06 12:44:12.12: [ 2893]: <-- data [2]
Feb 06 12:44:14.33: [ 2893]: --> [2:OK]
Feb 06 12:44:14.33: [ 2893]: <-- [9:AT+FRH=3\r]
Feb 06 12:44:15.45: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:17.18: [ 2893]: --> HDLC<25:FF C0 C2 82 0A CA 04 A2 32 F2 6A 32 82 6A 04 92 72 82 92 22 4A 82 42 93 71>
Feb 06 12:44:17.18: [ 2893]: --> [2:OK]
Feb 06 12:44:17.18: [ 2893]: REMOTE TSI "BARDIA***** "
Feb 06 12:44:17.18: [ 2893]: <-- [9:AT+FRH=3\r]
Feb 06 12:44:17.20: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:17.61: [ 2893]: --> HDLC<9:FF C8 C1 00 46 1F 00 3D 9B>
Feb 06 12:44:17.61: [ 2893]: --> [2:OK]
Feb 06 12:44:17.61: [ 2893]: REMOTE wants 14400 bit/s
Feb 06 12:44:17.61: [ 2893]: REMOTE wants A4 page width (215 mm)
Feb 06 12:44:17.61: [ 2893]: REMOTE wants unlimited page length
Feb 06 12:44:17.61: [ 2893]: REMOTE wants 7.7 line/mm
Feb 06 12:44:17.61: [ 2893]: REMOTE wants 1-D MH
Feb 06 12:44:17.61: [ 2893]: RECV training at v.17 14400 bit/s
Feb 06 12:44:17.61: [ 2893]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Feb 06 12:44:17.61: [ 2893]: <-- [11:AT+FRM=145\r]
Feb 06 12:44:19.38: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:20.86: [ 2893]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Feb 06 12:44:20.86: [ 2893]: RECV: TCF 2656 bytes, 0% non-zero, 2654 zero-run
Feb 06 12:44:20.86: [ 2893]: --> [10:NO CARRIER]
Feb 06 12:44:20.86: [ 2893]: <-- [9:AT+FRS=7\r]
Feb 06 12:44:20.95: [ 2893]: --> [2:OK]
Feb 06 12:44:20.95: [ 2893]: TRAINING succeeded
Feb 06 12:44:20.95: [ 2893]: --> [2:OK]
Feb 06 12:44:20.95: [ 2893]: TRAINING succeeded
Feb 06 12:44:20.95: [ 2893]: <-- [9:AT+FTH=3\r]
Feb 06 12:44:21.81: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:21.81: [ 2893]: <-- HDLC<3:FF C8 21>
Feb 06 12:44:21.81: [ 2893]: <-- data [3]
Feb 06 12:44:21.81: [ 2893]: <-- data [2]
Feb 06 12:44:22.13: [ 2893]: --> [2:OK]
Feb 06 12:44:22.14: [ 2893]: <-- [11:AT+FRM=146\r]
Feb 06 12:44:23.02: [ 2893]: --> [7:CONNECT]
Feb 06 12:44:23.02: [ 2893]: MODEM input buffering enabled
Feb 06 12:44:23.02: [ 2893]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Feb 06 12:44:23.02: [ 2893]: RECV: begin page
Feb 06 12:45:23.14: [ 2893]: MODEM TIMEOUT: reading from modem
Feb 06 12:45:23.14: [ 2893]: <-- data [1]
Feb 06 12:45:23.14: [ 2893]: RECV: Missing EOL after 5 seconds
Feb 06 12:45:23.14: [ 2893]: RECV: end page
Feb 06 12:45:25.14: [ 2893]: MODEM TIMEOUT: reading line from modem
Feb 06 12:45:25.14: [ 2893]: MODEM <Timeout>
Feb 06 12:45:27.14: [ 2893]: MODEM TIMEOUT: reading line from modem
Feb 06 12:45:27.14: [ 2893]: MODEM <Empty line>
Feb 06 12:45:29.14: [ 2893]: MODEM TIMEOUT: reading line from modem
Feb 06 12:45:29.14: [ 2893]: MODEM <Empty line>
Feb 06 12:45:29.14: [ 2893]: <-- data [1]
Feb 06 12:45:29.34: [ 2893]: MODEM TIMEOUT: reading line from modem
Feb 06 12:45:29.34: [ 2893]: MODEM <Timeout>
Feb 06 12:45:29.34: [ 2893]: RECV FAX (000001596): recvq/fax000001219.tif from BAR***, route to <unspecified>, 0 pages in 1:17
Feb 06 12:45:29.34: [ 2893]: RECV FAX: T.30 T2 timeout, expected page not received
Feb 06 12:45:29.34: [ 2893]: <-- [9:AT+FTH=3\r]
Feb 06 12:45:30.31: [ 2893]: --> [7:CONNECT]
Feb 06 12:45:30.31: [ 2893]: <-- HDLC<3:FF C8 5F>
Feb 06 12:45:30.31: [ 2893]: <-- data [3]
Feb 06 12:45:30.31: [ 2893]: <-- data [2]
Feb 06 12:45:30.74: [ 2893]: --> [2:OK]
Feb 06 12:45:30.74: [ 2893]: RECV FAX (000001596): session with BA**** terminated abnormally: T.30 T2 timeout, expected page not received
Feb 06 12:45:30.74: [ 2893]: RECV FAX: bin/faxrcvd.faxweb "recvq/fax000001219.tif" "ttyS0" "000001596" "T.30 T2 timeout, expected page not received"
Feb 06 12:45:30.74: [ 2893]: RECV FAX: end
Feb 06 12:45:30.74: [ 2893]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Modem Timeout
- From: Alessio Fattorini
- Re: [hylafax-users] Modem Timeout
- Prev by Date: Re: [hylafax-users] Solaris and USB modems
- Next by Date: [hylafax-users] not able to send fax from my hylafax server
- Previous by thread: Re: [hylafax-users] Solaris and USB modems
- Next by thread: Re: [hylafax-users] Modem Timeout
- Index(es):
Project hosted by iFAX Solutions