[hylafax-users] "T.30 T2 timeout, expected page not received" ERROR

["Bill Fung" <bill@xxxxxxxxx>]

Hi,

I encounter this error for 5% of the fax received. I browse thru the
archive and cannot find any solid solution. Could you please kindly help?

Thanks in advanced for your precious help!

bill
==========================================================
Background:
- hylafax-4.3.4
- Fedora Core 6

(1) /var/spool/hylafax/etc/config.ttySL0
CountryCode:            852
AreaCode:               0
FAXNumber:              "+852 XXXXXXXX"
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          low
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "+852 XXXXXXXX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           50
PercentGoodLines:       80
ModemType:              Class1          # use this to supply a hint
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before
PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before EOP
Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and trans
Class1TrainingRecovery: 1500            # 1.5sec delay after training failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF
duration

(2) error log email
-----Original Message-----
From: FAX Server [mailto:fax@xxxxxxxxxxx]
Sent: Friday, November 28, 2008 4:57 PM
To: FaxMaster@xxxxxxxxxxx
Subject: Fax received with errors from "yyyyyyyy"

recvq/fax000001782.tif (ftp://192.168.20.254:4559/recvq/fax000001782.tif):
          Sender: yyyyyyyy
           Pages: 1
         Quality: Fine
            Size: 1728 by 43
        Received: 2008:11:28 16:56:33
 Time To Receive: 0:46
     Signal Rate: 9600 bit/s
     Data Format: 2-D MR
   Error Correct: No
         CallID1:
         CallID2:
     Received On: ttySL0


Session log:
Nov 28 16:55:49.25: [ 2444]: SESSION BEGIN 000001794 852xxxxxxxx
Nov 28 16:55:49.25: [ 2444]: HylaFAX (tm) Version 4.3.4
Nov 28 16:55:49.25: [ 2444]: <-- [4:ATA\r]
Nov 28 16:55:54.83: [ 2444]: --> [7:CONNECT]
Nov 28 16:55:54.83: [ 2444]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttySL0'
Nov 28 16:55:54.83: [ 2444]: RECV FAX: begin
Nov 28 16:55:54.83: [ 2444]: <-- data [32]
Nov 28 16:55:54.83: [ 2444]: <-- data [2]
Nov 28 16:55:56.91: [ 2444]: --> [7:CONNECT]
Nov 28 16:55:56.91: [ 2444]: <-- data [23]
Nov 28 16:55:56.91: [ 2444]: <-- data [2]
Nov 28 16:55:57.75: [ 2444]: --> [7:CONNECT]
Nov 28 16:55:57.75: [ 2444]: <-- data [13]
Nov 28 16:55:57.75: [ 2444]: <-- data [2]
Nov 28 16:55:58.31: [ 2444]: --> [2:OK]
Nov 28 16:55:58.31: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:55:58.75: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:00.39: [ 2444]: --> [2:OK]
Nov 28 16:56:00.39: [ 2444]: REMOTE TSI "yyyyyyyy"
Nov 28 16:56:00.39: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:00.41: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:00.69: [ 2444]: --> [2:OK]
Nov 28 16:56:00.69: [ 2444]: REMOTE wants 14400 bit/s
Nov 28 16:56:00.69: [ 2444]: REMOTE wants A4 page width (215 mm)
Nov 28 16:56:00.69: [ 2444]: REMOTE wants unlimited page length
Nov 28 16:56:00.69: [ 2444]: REMOTE wants 7.7 line/mm
Nov 28 16:56:00.69: [ 2444]: REMOTE wants 2-D MR
Nov 28 16:56:00.69: [ 2444]: RECV training at v.17 14400 bit/s
Nov 28 16:56:00.69: [ 2444]: <-- [11:AT+FRM=145\r]
Nov 28 16:56:02.35: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:03.87: [ 2444]: RECV: TCF 2699 bytes, 0% non-zero, 1315
zero-run
Nov 28 16:56:03.87: [ 2444]: RECV: reject TCF (zero run too short, min 1800)
Nov 28 16:56:03.89: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:03.89: [ 2444]: <-- [9:AT+FRS=7\r]
Nov 28 16:56:03.95: [ 2444]: --> [2:OK]
Nov 28 16:56:03.95: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:56:04.03: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:04.03: [ 2444]: <-- data [3]
Nov 28 16:56:04.03: [ 2444]: <-- data [2]
Nov 28 16:56:05.33: [ 2444]: --> [2:OK]
Nov 28 16:56:05.33: [ 2444]: TRAINING failed
Nov 28 16:56:05.33: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:05.69: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:07.31: [ 2444]: --> [2:OK]
Nov 28 16:56:07.31: [ 2444]: REMOTE TSI "yyyyyyyy"
Nov 28 16:56:07.31: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:07.33: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:07.61: [ 2444]: --> [2:OK]
Nov 28 16:56:07.61: [ 2444]: REMOTE wants 14400 bit/s
Nov 28 16:56:07.61: [ 2444]: REMOTE wants A4 page width (215 mm)
Nov 28 16:56:07.61: [ 2444]: REMOTE wants unlimited page length
Nov 28 16:56:07.61: [ 2444]: REMOTE wants 7.7 line/mm
Nov 28 16:56:07.61: [ 2444]: REMOTE wants 2-D MR
Nov 28 16:56:07.61: [ 2444]: RECV training at v.17 14400 bit/s
Nov 28 16:56:07.61: [ 2444]: <-- [11:AT+FRM=145\r]
Nov 28 16:56:09.27: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:10.81: [ 2444]: RECV: TCF 2700 bytes, 0% non-zero, 1564
zero-run
Nov 28 16:56:10.81: [ 2444]: RECV: reject TCF (zero run too short, min 1800)
Nov 28 16:56:10.83: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:10.83: [ 2444]: <-- [9:AT+FRS=7\r]
Nov 28 16:56:10.89: [ 2444]: --> [2:OK]
Nov 28 16:56:10.89: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:56:10.97: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:10.97: [ 2444]: <-- data [3]
Nov 28 16:56:10.97: [ 2444]: <-- data [2]
Nov 28 16:56:12.29: [ 2444]: --> [2:OK]
Nov 28 16:56:12.29: [ 2444]: TRAINING failed
Nov 28 16:56:12.29: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:12.61: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:14.27: [ 2444]: --> [2:OK]
Nov 28 16:56:14.27: [ 2444]: REMOTE TSI "yyyyyyyy"
Nov 28 16:56:14.27: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:14.29: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:14.57: [ 2444]: --> [2:OK]
Nov 28 16:56:14.57: [ 2444]: REMOTE wants 12000 bit/s
Nov 28 16:56:14.57: [ 2444]: REMOTE wants A4 page width (215 mm)
Nov 28 16:56:14.57: [ 2444]: REMOTE wants unlimited page length
Nov 28 16:56:14.57: [ 2444]: REMOTE wants 7.7 line/mm
Nov 28 16:56:14.57: [ 2444]: REMOTE wants 2-D MR
Nov 28 16:56:14.57: [ 2444]: RECV training at v.17 12000 bit/s
Nov 28 16:56:14.57: [ 2444]: <-- [11:AT+FRM=121\r]
Nov 28 16:56:16.23: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:17.77: [ 2444]: RECV: TCF 2250 bytes, 0% non-zero, 1323
zero-run
Nov 28 16:56:17.77: [ 2444]: RECV: reject TCF (zero run too short, min 1500)
Nov 28 16:56:17.79: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:17.79: [ 2444]: <-- [9:AT+FRS=7\r]
Nov 28 16:56:17.85: [ 2444]: --> [2:OK]
Nov 28 16:56:17.85: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:56:17.93: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:17.93: [ 2444]: <-- data [3]
Nov 28 16:56:17.93: [ 2444]: <-- data [2]
Nov 28 16:56:19.23: [ 2444]: --> [2:OK]
Nov 28 16:56:19.23: [ 2444]: TRAINING failed
Nov 28 16:56:19.23: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:19.57: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:21.23: [ 2444]: --> [2:OK]
Nov 28 16:56:21.23: [ 2444]: REMOTE TSI "yyyyyyyy"
Nov 28 16:56:21.23: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:21.25: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:21.53: [ 2444]: --> [2:OK]
Nov 28 16:56:21.53: [ 2444]: REMOTE wants 12000 bit/s
Nov 28 16:56:21.53: [ 2444]: REMOTE wants A4 page width (215 mm)
Nov 28 16:56:21.53: [ 2444]: REMOTE wants unlimited page length
Nov 28 16:56:21.53: [ 2444]: REMOTE wants 7.7 line/mm
Nov 28 16:56:21.53: [ 2444]: REMOTE wants 2-D MR
Nov 28 16:56:21.53: [ 2444]: RECV training at v.17 12000 bit/s
Nov 28 16:56:21.53: [ 2444]: <-- [11:AT+FRM=121\r]
Nov 28 16:56:23.19: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:24.73: [ 2444]: RECV: TCF 2250 bytes, 0% non-zero, 1071
zero-run
Nov 28 16:56:24.73: [ 2444]: RECV: reject TCF (zero run too short, min 1500)
Nov 28 16:56:24.75: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:24.75: [ 2444]: <-- [9:AT+FRS=7\r]
Nov 28 16:56:24.81: [ 2444]: --> [2:OK]
Nov 28 16:56:24.81: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:56:24.89: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:24.89: [ 2444]: <-- data [3]
Nov 28 16:56:24.89: [ 2444]: <-- data [2]
Nov 28 16:56:26.19: [ 2444]: --> [2:OK]
Nov 28 16:56:26.19: [ 2444]: TRAINING failed
Nov 28 16:56:26.19: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:26.57: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:28.19: [ 2444]: --> [2:OK]
Nov 28 16:56:28.19: [ 2444]: REMOTE TSI "yyyyyyyy"
Nov 28 16:56:28.19: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:56:28.21: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:28.49: [ 2444]: --> [2:OK]
Nov 28 16:56:28.49: [ 2444]: REMOTE wants 9600 bit/s
Nov 28 16:56:28.49: [ 2444]: REMOTE wants A4 page width (215 mm)
Nov 28 16:56:28.49: [ 2444]: REMOTE wants unlimited page length
Nov 28 16:56:28.49: [ 2444]: REMOTE wants 7.7 line/mm
Nov 28 16:56:28.49: [ 2444]: REMOTE wants 2-D MR
Nov 28 16:56:28.49: [ 2444]: RECV training at v.17 9600 bit/s
Nov 28 16:56:28.49: [ 2444]: <-- [10:AT+FRM=97\r]
Nov 28 16:56:30.15: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:31.69: [ 2444]: RECV: TCF 1824 bytes, 0% non-zero, 1800
zero-run
Nov 28 16:56:31.71: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:31.71: [ 2444]: <-- [9:AT+FRS=7\r]
Nov 28 16:56:31.77: [ 2444]: --> [2:OK]
Nov 28 16:56:31.77: [ 2444]: TRAINING succeeded
Nov 28 16:56:31.77: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:56:31.85: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:31.85: [ 2444]: <-- data [3]
Nov 28 16:56:31.85: [ 2444]: <-- data [2]
Nov 28 16:56:33.17: [ 2444]: --> [2:OK]
Nov 28 16:56:33.17: [ 2444]: <-- [10:AT+FRM=98\r]
Nov 28 16:56:33.89: [ 2444]: --> [7:CONNECT]
Nov 28 16:56:33.89: [ 2444]: RECV: begin page
Nov 28 16:56:40.06: [ 2444]: RECV: 335 total lines, 0 bad lines, 0
consecutive bad lines
Nov 28 16:56:40.07: [ 2444]: RECV: end page
Nov 28 16:56:40.07: [ 2444]: --> [10:NO CARRIER]
Nov 28 16:56:40.07: [ 2444]: <-- [9:AT+FRH=3\r]
Nov 28 16:57:20.07: [ 2444]: --> [0:]
Nov 28 16:57:20.07: [ 2444]: MODEM <Empty line>
Nov 28 16:57:20.07: [ 2444]: <-- data [1]
Nov 28 16:57:20.27: [ 2444]: MODEM <Timeout>
Nov 28 16:57:20.27: [ 2444]: RECV keeping unconfirmed page
Nov 28 16:57:20.27: [ 2444]: RECV FAX (000001794): from yyyyyyyy, page 1 in
0:46, INF, 7.7 line/mm, 2-D MR, 9600 bit/s
Nov 28 16:57:20.27: [ 2444]: RECV FAX (000001794): recvq/fax000001782.tif
from yyyyyyyy, route to <unspecified>, 1 pages in 1:26
Nov 28 16:57:20.27: [ 2444]: RECV FAX: T.30 T2 timeout, expected page not
received
Nov 28 16:57:20.27: [ 2444]: <-- [9:AT+FTH=3\r]
Nov 28 16:57:27.82: [ 2444]: --> [0:]
Nov 28 16:57:27.82: [ 2444]: RECV FAX (000001794): session with yyyyyyyy
terminated abnormally: T.30 T2 timeout, expected page not received
Nov 28 16:57:27.82: [ 2444]: RECV FAX: bin/faxrcvd "recvq/fax000001782.tif"
"ttySL0" "000001794" "T.30 T2 timeout, expected page not received"
Nov 28 16:57:27.82: [ 2444]: RECV FAX: end
Nov 28 16:57:27.82: [ 2444]: SESSION END




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*