[hylafax-users] Error communicating from hylafax 4.4.4 to hylafax 4.4.4

[Giuseppe Sacco <giuseppe@xxxxxxxxxxxxxxxxxxxxxxxxx>]

Hi hylafax gurus,
yesterday I tried a new installation on a test machine. It is a foolong
minicomputer running Debian lenny and hylafax 4.4.4. On this computer I
connected a MultiModem 5656ZDX used in class1. The other end is a normal
PC with a LEONARDO Digicom modemfax used in class1.0. Both machines use
the same software (hylafax, libtiff, awk, bash).

When I send a fax from DIGICOM to MultiModem, a few pages are correctly
transferred, but the communication fails with this message on the sender
side:

[...]
Nov 26 10:36:11.26: [26788]: <-- data [1028]
Nov 26 10:36:13.40: [26788]: <-- data [1032]
Nov 26 10:36:13.40: [26788]: <-- data [786]
Nov 26 10:36:13.40: [26788]: SENT 47886 bytes of data
Nov 26 10:36:13.40: [26788]: SEND 2D RTC
Nov 26 10:36:13.40: [26788]: <-- data [30]
Nov 26 10:36:13.40: [26788]: <-- data [2]
Nov 26 10:36:13.40: [26788]: SEND end page
Nov 26 10:36:13.40: [26788]: --> [2:OK]
Nov 26 10:36:13.40: [26788]: <-- [9:AT+FTS=9\r]
Nov 26 10:36:13.40: [26788]: --> [7:CONNECT]
Nov 26 10:36:13.40: [26788]: --> [2:OK]
Nov 26 10:36:13.40: [26788]: SEND send EOP (no more pages or documents)
Nov 26 10:36:13.40: [26788]: <-- [9:AT+FTH=3\r]
Nov 26 10:36:13.40: [26788]: --> [2:OK]
Nov 26 10:36:13.40: [26788]: SEND send EOP (no more pages or documents)
Nov 26 10:36:13.40: [26788]: <-- [9:AT+FTH=3\r]
Nov 26 10:36:14.75: [26788]: --> [6:<8D><8A><CF>ˍ<8A>]
Nov 26 10:36:14.75: [26788]: SEND send EOP (no more pages or documents)
Nov 26 10:36:14.75: [26788]: <-- [9:AT+FTH=3\r]
Nov 26 10:36:14.75: [26788]: --> [2:OK]
Nov 26 10:36:14.75: [26788]: No response to EOP repeated 3 tries
Nov 26 10:36:14.75: [26788]: <-- [9:AT+FRS=7\r]
Nov 26 10:36:14.80: [26788]: --> [7:CONNECT]
Nov 26 10:36:20.83: [26788]: --> [2:OK]
Nov 26 10:36:20.83: [26788]: <-- [9:AT+FTH=3\r]
Nov 26 10:36:20.88: [26788]: --> [7:CONNECT]
Nov 26 10:36:20.88: [26788]: <-- HDLC<3:FF C8 DF>
Nov 26 10:36:20.88: [26788]: <-- data [3]
Nov 26 10:36:20.88: [26788]: <-- data [2]
Nov 26 10:36:22.20: [26788]: --> [2:OK]
Nov 26 10:36:22.20: [26788]: MODEM input buffering enabled
Nov 26 10:36:22.20: [26788]: SEND FAILED: JOB 68 DEST 0123456789 ERR [334] No response to EOP repeated 3 tries; 
too many attempts to send
Nov 26 10:36:23.20: [26788]: <-- [5:ATH0\r]
Nov 26 10:36:25.76: [26788]: --> [2:OK]
Nov 26 10:36:25.76: [26788]: MODEM set DTR OFF
Nov 26 10:36:25.76: [26788]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 26 10:36:25.76: [26788]: SESSION END

while on the receiver side I see:

[...]
nov 26 10:35:42.94: [ 9455]: <-- data [2]
nov 26 10:35:44.23: [ 9455]: --> [2:OK]
nov 26 10:35:44.23: [ 9455]: <-- [11:AT+FRM=146\r]
nov 26 10:35:45.49: [ 9455]: --> [7:CONNECT]
nov 26 10:35:45.49: [ 9455]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
nov 26 10:35:45.49: [ 9455]: RECV: begin page
nov 26 10:36:03.36: [ 9455]: RECV/CQ: Bad 1D pixel count, row 1341, got 0, expected 1728
nov 26 10:36:03.36: [ 9455]: RECV/CQ: Bad 1D pixel count, row 1342, got 0, expected 1728
nov 26 10:36:03.36: [ 9455]: RECV/CQ: Bad 1D pixel count, row 1343, got 0, expected 1728
nov 26 10:36:03.36: [ 9455]: RECV/CQ: Bad 1D pixel count, row 1344, got 0, expected 1728
nov 26 10:36:03.36: [ 9455]: RECV/CQ: Adjusting for RTC found at row 1341
nov 26 10:36:03.36: [ 9455]: RECV: 1341 total lines, 0 bad lines, 0 consecutive bad lines
nov 26 10:36:03.36: [ 9455]: RECV: end page
nov 26 10:36:03.36: [ 9455]: --> [10:NO CARRIER]
nov 26 10:36:03.36: [ 9455]: <-- [9:AT+FRH=3\r]
nov 26 10:36:15.00: [ 9455]: --> [7:CONNECT]
nov 26 10:36:20.62: [ 9455]: --> [2:10 03]
nov 26 10:36:20.62: [ 9455]: --> [5:ERROR]
nov 26 10:36:20.62: [ 9455]: MODEM Command error
nov 26 10:36:20.62: [ 9455]: FCS error
nov 26 10:36:20.62: [ 9455]: <-- [10:AT+FRS=21\r]
nov 26 10:36:22.38: [ 9455]: --> [2:OK]
nov 26 10:36:22.38: [ 9455]: <-- [9:AT+FTH=3\r]
nov 26 10:36:22.52: [ 9455]: --> [7:CONNECT]
nov 26 10:36:22.52: [ 9455]: <-- HDLC<3:FF C8 58>
nov 26 10:36:22.52: [ 9455]: <-- data [3]
nov 26 10:36:22.52: [ 9455]: <-- data [2]
nov 26 10:36:23.81: [ 9455]: --> [2:OK]
nov 26 10:36:23.81: [ 9455]: RECV send CRP (command repeat)
nov 26 10:36:23.81: [ 9455]: <-- [9:AT+FRH=3\r]
nov 26 10:37:09.32: [ 9455]: --> [0:]
nov 26 10:37:09.32: [ 9455]: MODEM <Empty line>
nov 26 10:37:09.32: [ 9455]: MODEM TIMEOUT: waiting for v.21 carrier
nov 26 10:37:09.32: [ 9455]: <-- data [1]
nov 26 10:37:09.48: [ 9455]: --> [2:OK]
nov 26 10:37:09.48: [ 9455]: <-- [9:AT+FRH=3\r]
nov 26 10:37:16.48: [ 9455]: --> [0:]
nov 26 10:37:16.48: [ 9455]: MODEM <Empty line>
nov 26 10:37:16.48: [ 9455]: MODEM TIMEOUT: waiting for v.21 carrier
nov 26 10:37:16.48: [ 9455]: <-- data [1]
nov 26 10:37:16.64: [ 9455]: --> [2:OK]
nov 26 10:37:16.64: [ 9455]: RECV keeping unconfirmed page
nov 26 10:37:16.64: [ 9455]: RECV FAX (000000004): from Lixper S.r.L., page 4 in 0:22, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
nov 26 10:37:16.64: [ 9455]: RECV FAX (000000004): recvq/fax000000004.tif from Lixper S.r.L., route to <unspecified>, 4 pages in 3:32
nov 26 10:37:16.64: [ 9455]: RECV FAX: T.30 T2 timeout, expected page not received
nov 26 10:37:16.64: [ 9455]: <-- [9:AT+FTH=3\r]
nov 26 10:37:16.79: [ 9455]: --> [7:CONNECT]
nov 26 10:37:16.79: [ 9455]: <-- HDLC<3:FF C8 5F>
nov 26 10:37:16.79: [ 9455]: <-- data [3]
nov 26 10:37:16.79: [ 9455]: <-- data [2]
nov 26 10:37:18.08: [ 9455]: --> [2:OK]
nov 26 10:37:18.08: [ 9455]: RECV FAX (000000004): session with Lixper S.r.L. terminated abnormally: T.30 T2 timeout, expected page not received
nov 26 10:37:18.08: [ 9455]: RECV FAX: bin/faxrcvd "recvq/fax000000004.tif" "ttyS0" "000000004" "T.30 T2 timeout, expected page not received"
nov 26 10:37:18.09: [ 9455]: RECV FAX: end
nov 26 10:37:18.09: [ 9455]: T.30 T2 timeout, expected page not received
nov 26 10:37:18.09: [ 9455]: SESSION END

Do you have any suggestion on what is going on?

Thanks,
Giuseppe


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*