Re: [hylafax-users] ModemWaitTimeCmd is not working

[Tomas Novosad <kbbl@xxxxxxxx>]

Hello,

i'v looked bit closer on the modem.

I'd connect to modem via minicom a issued all AT command manually.
in first test case i dialed a number without setting modem to fax mode
ATS7=120 -> OK
ATDT737309887
- modem called to my mobile, i accepted the call and modem hanged after about two minutes with "NO CARRIER"
 so this was working

However in second test scenario, i set modem into FAX CLASS2
AT+FCLASS=2 -> OK
ATS7=120 -> OK
ATDT737309887
and modem responded  +FHNG:11 (No Answer (T.30 T1 timeout))
after about 60 seconds.

This mean, when modem is in fax mode, the T1 timeout has to be set by different command then ATS7

Does any of you know about such command?
I've already asked ISDN card supplier, but so far with no luck.

Thank you for any idea
Tomas Novosad

------------ Původní zpráva ------------
Od: Tomas Novosad <kbbl@xxxxxxxx>
Předmět: [hylafax-users] ModemWaitTimeCmd is not working
Datum: 08.10.2008 14:43:55
----------------------------------------
Hello everybody,

I have EICON DIVA SERVER ISDN PRI card with Hylafax running.

I need to rise "NO CARRIER" timeout up to smth like 120 secs (default is 60).
I'm using "ModemWaitTimeCmd: ATS7=120"  config command, but this does not help
the thing.

Does anyone have an idea how to rise time before modem quit faxing?
This is because faxes on remotre side are handled manualy and it take some time
- obviously a bit longet then the modem timeout is.

Thank you for any advice.

More details follows
my modem config is
--------------------------------
CountryCode:            420
AreaCode:               ""
FAXNumber:              ""
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          off
#GettyArgs:             "-h %l dx_%s"
GettyArgs:              "-b -r -s %s %l"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "Od %%l|%c|Strana %%P z %%T"
MaxRecvPages:           25
UseJobTSI:      Yes
ModemType:              Class1          # use this to supply a hint
PercentGoodLines:      87
MaxConsecutiveBadLines:13
ModemWaitTimeCmd:       ATS7=120
ModemResetCmds:         AT#CID=14
CallIDPattern:          "CID: "
CallIDPattern:          "DAD: "
----------------------

however modem always return NO CARRIER after about a minute
I  also tried to forece the timeout command into ModemDialCmd - like this
ModemDialCmd: "AT S7=120 S7? DT%s"

but still no luck - see the session log
at first set the timeout with ATS7=120 -> OK
then verify timeout value ATS7? ->  78  (hex value)
then dial with ATDT
however modem quit with NO CARRIER after some 70 secs
-----------------
Oct 08 14:34:12.11: [22427]: SESSION BEGIN 000010191 420737309887
Oct 08 14:34:12.11: [22427]: HylaFAX (tm) Version 4.4.4
Oct 08 14:34:12.11: [22427]: SEND FAX: JOB 1807 DEST 737309887 COMMID 000010191
DEVICE '/dev/ttyds30' FROM 'tomas <tomas@xxxxxxxxxxx>' USER root
Oct 08 14:34:12.11: [22427]: <-- [12:AT+FCLASS=1\r]
Oct 08 14:34:12.11: [22427]: --> [2:OK]
Oct 08 14:34:12.11: [22427]: DIAL 737309887
Oct 08 14:34:12.11: [22427]: <-- [9:ATS7=120\r]
Oct 08 14:34:12.11: [22427]: --> [2:OK]
Oct 08 14:34:12.11: [22427]: <-- [6:ATS7?\r]
Oct 08 14:34:12.11: [22427]: --> [6:R07=78]
Oct 08 14:34:12.11: [22427]: --> [2:OK]
Oct 08 14:34:12.11: [22427]: <-- [14:ATDT737309887\r]
Oct 08 14:35:36.28: [22427]: --> [10:NO CARRIER]
Oct 08 14:35:36.28: [22427]: SEND FAILED: JOB 1807 DEST 737309887 ERR [2] No
carrier detected
Oct 08 14:35:36.28: [22427]: SEND FAILED: JOB 1807 DEST 737309887 ERR [333] No
carrier detected; too many attempts to dial
Oct 08 14:35:37.29: [22427]: <-- [5:ATH0\r]
Oct 08 14:35:37.29: [22427]: --> [2:OK]
Oct 08 14:35:37.29: [22427]: SESSION END
------------------------------



Tomáš Novosad
mailto:kbbl@xxxxxxxx
jabber:kbbl@xxxxxxxxx
icq:499392313
+420737309887
# rm -rf /*


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*





Tomáš Novosad
mailto:kbbl@xxxxxxxx
jabber:kbbl@xxxxxxxxx
icq:499392313
+420737309887
# rm -rf /*


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*