[hylafax-users] Fwd: Usr courier business cannot receive faxes

["Fernando Henrique" <eaglemac@xxxxxxxxx>]

I have a USR813453C courier Business modem, latest firmware 2.3.15, using Hylafax 4.3.1-7 in a Debian 40r4a distro.

I can send faxes, but cannot receive. Here goes my config.ttyS1 and a receive log:

I tried almost any combination, Class 1, class 2.0, removed AT+FRS=n command, changed speed, changed flow control, etc.

 

 

Config.ttyS1:

 

CountryCode: 351

AreaCode: 236

FAXNumber: +351.236.xxxxxx

LongDistancePrefix: 1

InternationalPrefix: 00

DialStringRules: etc/dialrules

ServerTracing: 1

SessionTracing: 11

RecvFileMode: 0644

LogFileMode: 0666

DeviceMode: 0644

RingsBeforeAnswer: 2

SpeakerVolume: low

GettyArgs: "-h %l dx_%s"

LocalIdentifier: "xxxxxxxxx"

TagLineFont: etc/lutRS18.pcf

TagLineFormat: "From %%l|%c|Page %%P of %%T"

MaxRecvPages: 25

#

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType: Class1 # use class 1 interface

ModemRate: 19200 # rate for DCE-DTE communication

ModemFlowControl: xonxoff # software flow control

#

ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem

ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)

ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control

ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control

ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control

ModemResultCodesCmd: ATQ0X4 # enable result codes

#

ModemMfrQueryCmd: !USR

ModemModelQueryCmd: ATI3

ModemRevQueryCmd: ATI7 # XXX returns a multi-line result

#

# When AT+FCLASS=1 is issued the modem automatically switches

# to software flow control; these parameters let the fax software

# reset flow control as needed after entering Class 1.

#

Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control

Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control

Class1SFLOCmd: "" # modem does this automatically

#

# This should resolve "DIS/DTC received 3 times" errors:

#

Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response

#

# The remainder of this configuration is included so that the

# modem "idles" in Class 0 while not sending or receiving facsimile.

#

ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0

ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1

#

# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions

# this is not good. So, we seem to work-around that problem by not using the

# command. Unfortunately, this isn't an ideal thing.

#

Class1SwitchingCmd: "<delay\0727>"

 

Here goes a log:

 

Set 22 16:58:33.80: [20065]: SESSION BEGIN 000000069 351xxxxxxxxx

Set 22 16:58:33.80: [20065]: HylaFAX (tm) Version 4.3.1

Set 22 16:58:33.80: [20065]: <-- [13:AT+FCLASS=1A\r]

Set 22 16:58:38.97: [20065]: --> [7:CONNECT]

Set 22 16:58:38.97: [20065]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1'

Set 22 16:58:38.97: [20065]: RECV FAX: begin

Set 22 16:58:38.97: [20065]: <-- data [32]

Set 22 16:58:38.97: [20065]: <-- data [2]

Set 22 16:58:40.96: [20065]: --> [7:CONNECT]

Set 22 16:58:40.96: [20065]: <-- data [23]

Set 22 16:58:40.96: [20065]: <-- data [2]

Set 22 16:58:42.10: [20065]: --> [7:CONNECT]

Set 22 16:58:42.10: [20065]: <-- data [13]

Set 22 16:58:42.10: [20065]: <-- data [2]

Set 22 16:58:43.00: [20065]: --> [2:OK]

Set 22 16:58:43.00: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:58:44.15: [20065]: --> [7:CONNECT]

Set 22 16:58:44.82: [20065]: --> [2:OK]

Set 22 16:58:44.82: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:58:44.82: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:58:44.85: [20065]: --> [7:CONNECT]

Set 22 16:58:45.26: [20065]: --> [2:OK]

Set 22 16:58:45.26: [20065]: REMOTE wants 14400 bit/s

Set 22 16:58:45.26: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:58:45.26: [20065]: REMOTE wants unlimited page length

Set 22 16:58:45.26: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:58:45.26: [20065]: REMOTE wants 2-D MMR

Set 22 16:58:45.26: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:58:45.26: [20065]: RECV training at v.17 14400 bit/s

Set 22 16:58:45.26: [20065]: <-- [11:AT+FRM=145\r]

Set 22 16:58:49.76: [20065]: --> [0:]

Set 22 16:58:49.76: [20065]: MODEM <Empty line>

Set 22 16:58:49.76: [20065]: <-- data [1]

Set 22 16:58:49.77: [20065]: --> [2:OK]

Set 22 16:58:49.77: [20065]: DELAY 70 ms

Set 22 16:58:49.84: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:58:50.08: [20065]: --> [7:CONNECT]

Set 22 16:58:50.08: [20065]: <-- data [3]

Set 22 16:58:50.08: [20065]: <-- data [2]

Set 22 16:58:51.30: [20065]: --> [2:OK]

Set 22 16:58:51.30: [20065]: TRAINING failed

Set 22 16:58:51.30: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:58:52.46: [20065]: --> [7:CONNECT]

Set 22 16:58:53.13: [20065]: --> [2:OK]

Set 22 16:58:53.13: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:58:53.13: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:58:53.16: [20065]: --> [7:CONNECT]

Set 22 16:58:53.57: [20065]: --> [2:OK]

Set 22 16:58:53.57: [20065]: REMOTE wants 14400 bit/s

Set 22 16:58:53.57: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:58:53.57: [20065]: REMOTE wants unlimited page length

Set 22 16:58:53.57: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:58:53.57: [20065]: REMOTE wants 2-D MMR

Set 22 16:58:53.57: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:58:53.57: [20065]: RECV training at v.17 14400 bit/s

Set 22 16:58:53.57: [20065]: <-- [11:AT+FRM=145\r]

Set 22 16:58:58.07: [20065]: --> [0:]

Set 22 16:58:58.07: [20065]: MODEM <Empty line>

Set 22 16:58:58.07: [20065]: <-- data [1]

Set 22 16:58:58.08: [20065]: --> [2:OK]

Set 22 16:58:58.08: [20065]: DELAY 70 ms

Set 22 16:58:58.15: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:58:58.39: [20065]: --> [7:CONNECT]

Set 22 16:58:58.39: [20065]: <-- data [3]

Set 22 16:58:58.39: [20065]: <-- data [2]

Set 22 16:58:59.61: [20065]: --> [2:OK]

Set 22 16:58:59.61: [20065]: TRAINING failed

Set 22 16:58:59.61: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:00.78: [20065]: --> [7:CONNECT]

Set 22 16:59:01.44: [20065]: --> [2:OK]

Set 22 16:59:01.44: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:01.44: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:01.48: [20065]: --> [7:CONNECT]

Set 22 16:59:01.88: [20065]: --> [2:OK]

Set 22 16:59:01.88: [20065]: REMOTE wants 12000 bit/s

Set 22 16:59:01.88: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:01.88: [20065]: REMOTE wants unlimited page length

Set 22 16:59:01.88: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:01.88: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:01.88: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:01.88: [20065]: RECV training at v.17 12000 bit/s

Set 22 16:59:01.88: [20065]: <-- [11:AT+FRM=121\r]

Set 22 16:59:06.39: [20065]: --> [0:]

Set 22 16:59:06.39: [20065]: MODEM <Empty line>

Set 22 16:59:06.39: [20065]: <-- data [1]

Set 22 16:59:06.39: [20065]: --> [2:OK]

Set 22 16:59:06.39: [20065]: DELAY 70 ms

Set 22 16:59:06.47: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:06.71: [20065]: --> [7:CONNECT]

Set 22 16:59:06.71: [20065]: <-- data [3]

Set 22 16:59:06.71: [20065]: <-- data [2]

Set 22 16:59:07.93: [20065]: --> [2:OK]

Set 22 16:59:07.93: [20065]: TRAINING failed

Set 22 16:59:07.93: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:09.09: [20065]: --> [7:CONNECT]

Set 22 16:59:09.75: [20065]: --> [2:OK]

Set 22 16:59:09.75: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:09.75: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:09.79: [20065]: --> [7:CONNECT]

Set 22 16:59:10.19: [20065]: --> [2:OK]

Set 22 16:59:10.19: [20065]: REMOTE wants 12000 bit/s

Set 22 16:59:10.19: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:10.19: [20065]: REMOTE wants unlimited page length

Set 22 16:59:10.19: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:10.19: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:10.19: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:10.19: [20065]: RECV training at v.17 12000 bit/s

Set 22 16:59:10.19: [20065]: <-- [11:AT+FRM=121\r]

Set 22 16:59:14.70: [20065]: --> [0:]

Set 22 16:59:14.70: [20065]: MODEM <Empty line>

Set 22 16:59:14.70: [20065]: <-- data [1]

Set 22 16:59:14.71: [20065]: --> [2:OK]

Set 22 16:59:14.71: [20065]: DELAY 70 ms

Set 22 16:59:14.78: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:15.02: [20065]: --> [7:CONNECT]

Set 22 16:59:15.02: [20065]: <-- data [3]

Set 22 16:59:15.02: [20065]: <-- data [2]

Set 22 16:59:16.24: [20065]: --> [2:OK]

Set 22 16:59:16.24: [20065]: TRAINING failed

Set 22 16:59:16.24: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:17.41: [20065]: --> [7:CONNECT]

Set 22 16:59:18.08: [20065]: --> [2:OK]

Set 22 16:59:18.08: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:18.08: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:18.11: [20065]: --> [7:CONNECT]

Set 22 16:59:18.52: [20065]: --> [2:OK]

Set 22 16:59:18.52: [20065]: REMOTE wants 9600 bit/s

Set 22 16:59:18.52: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:18.52: [20065]: REMOTE wants unlimited page length

Set 22 16:59:18.52: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:18.52: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:18.52: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:18.52: [20065]: RECV training at v.17 9600 bit/s

Set 22 16:59:18.52: [20065]: <-- [10:AT+FRM=97\r]

Set 22 16:59:23.02: [20065]: --> [0:]

Set 22 16:59:23.02: [20065]: MODEM <Empty line>

Set 22 16:59:23.02: [20065]: <-- data [1]

Set 22 16:59:23.03: [20065]: --> [2:OK]

Set 22 16:59:23.03: [20065]: DELAY 70 ms

Set 22 16:59:23.10: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:23.35: [20065]: --> [7:CONNECT]

Set 22 16:59:23.35: [20065]: <-- data [3]

Set 22 16:59:23.35: [20065]: <-- data [2]

Set 22 16:59:24.56: [20065]: --> [2:OK]

Set 22 16:59:24.56: [20065]: TRAINING failed

Set 22 16:59:24.56: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:25.73: [20065]: --> [7:CONNECT]

Set 22 16:59:26.40: [20065]: --> [2:OK]

Set 22 16:59:26.40: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:26.40: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:26.43: [20065]: --> [7:CONNECT]

Set 22 16:59:26.84: [20065]: --> [2:OK]

Set 22 16:59:26.84: [20065]: REMOTE wants 9600 bit/s

Set 22 16:59:26.84: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:26.84: [20065]: REMOTE wants unlimited page length

Set 22 16:59:26.84: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:26.84: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:26.84: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:26.84: [20065]: RECV training at v.17 9600 bit/s

Set 22 16:59:26.84: [20065]: <-- [10:AT+FRM=97\r]

Set 22 16:59:28.61: [20065]: --> [7:CONNECT]

Set 22 16:59:33.36: [20065]: <-- data [1]

Set 22 16:59:33.37: [20065]: --> [7:–A G{šü]

Set 22 16:59:33.37: [20065]: DELAY 70 ms

Set 22 16:59:33.44: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:33.44: [20065]: --> [2:OK]

Set 22 16:59:33.44: [20065]: TRAINING failed

Set 22 16:59:33.44: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:33.69: [20065]: --> [7:CONNECT]

Set 22 16:59:38.71: [20065]: --> [5:ERROR]

Set 22 16:59:38.71: [20065]: MODEM Command error

Set 22 16:59:38.71: [20065]: FCS error

Set 22 16:59:38.71: [20065]: DELAY 70 ms

Set 22 16:59:38.78: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:39.02: [20065]: --> [7:CONNECT]

Set 22 16:59:39.02: [20065]: <-- data [3]

Set 22 16:59:39.02: [20065]: <-- data [2]

Set 22 16:59:40.23: [20065]: --> [2:OK]

Set 22 16:59:40.23: [20065]: RECV send CRP (command repeat)

Set 22 16:59:40.23: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:41.40: [20065]: --> [7:CONNECT]

Set 22 16:59:42.07: [20065]: --> [2:OK]

Set 22 16:59:42.07: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:42.07: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:42.10: [20065]: --> [7:CONNECT]

Set 22 16:59:42.51: [20065]: --> [2:OK]

Set 22 16:59:42.51: [20065]: REMOTE wants 9600 bit/s

Set 22 16:59:42.51: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:42.51: [20065]: REMOTE wants unlimited page length

Set 22 16:59:42.51: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:42.51: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:42.51: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:42.51: [20065]: RECV training at v.17 9600 bit/s

Set 22 16:59:42.51: [20065]: <-- [10:AT+FRM=97\r]

Set 22 16:59:47.02: [20065]: --> [0:]

Set 22 16:59:47.02: [20065]: MODEM <Empty line>

Set 22 16:59:47.02: [20065]: <-- data [1]

Set 22 16:59:47.02: [20065]: --> [2:OK]

Set 22 16:59:47.02: [20065]: DELAY 70 ms

Set 22 16:59:47.10: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:47.34: [20065]: --> [7:CONNECT]

Set 22 16:59:47.34: [20065]: <-- data [3]

Set 22 16:59:47.34: [20065]: <-- data [2]

Set 22 16:59:48.56: [20065]: --> [2:OK]

Set 22 16:59:48.56: [20065]: TRAINING failed

Set 22 16:59:48.56: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:49.72: [20065]: --> [7:CONNECT]

Set 22 16:59:50.39: [20065]: --> [2:OK]

Set 22 16:59:50.39: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:50.39: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:50.42: [20065]: --> [7:CONNECT]

Set 22 16:59:50.83: [20065]: --> [2:OK]

Set 22 16:59:50.83: [20065]: REMOTE wants 7200 bit/s

Set 22 16:59:50.83: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:50.83: [20065]: REMOTE wants unlimited page length

Set 22 16:59:50.83: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:50.83: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:50.83: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:50.83: [20065]: RECV training at v.17 7200 bit/s

Set 22 16:59:50.83: [20065]: <-- [10:AT+FRM=73\r]

Set 22 16:59:55.33: [20065]: --> [0:]

Set 22 16:59:55.33: [20065]: MODEM <Empty line>

Set 22 16:59:55.33: [20065]: <-- data [1]

Set 22 16:59:55.34: [20065]: --> [2:OK]

Set 22 16:59:55.34: [20065]: DELAY 70 ms

Set 22 16:59:55.41: [20065]: <-- [9:AT+FTH=3\r]

Set 22 16:59:55.65: [20065]: --> [7:CONNECT]

Set 22 16:59:55.65: [20065]: <-- data [3]

Set 22 16:59:55.65: [20065]: <-- data [2]

Set 22 16:59:56.87: [20065]: --> [2:OK]

Set 22 16:59:56.87: [20065]: TRAINING failed

Set 22 16:59:56.87: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:58.04: [20065]: --> [7:CONNECT]

Set 22 16:59:58.70: [20065]: --> [2:OK]

Set 22 16:59:58.70: [20065]: REMOTE TSI "236xxxxxx"

Set 22 16:59:58.70: [20065]: <-- [9:AT+FRH=3\r]

Set 22 16:59:58.74: [20065]: --> [7:CONNECT]

Set 22 16:59:59.14: [20065]: --> [2:OK]

Set 22 16:59:59.14: [20065]: REMOTE wants 7200 bit/s

Set 22 16:59:59.14: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 16:59:59.14: [20065]: REMOTE wants unlimited page length

Set 22 16:59:59.14: [20065]: REMOTE wants 3.85 line/mm

Set 22 16:59:59.14: [20065]: REMOTE wants 2-D MMR

Set 22 16:59:59.14: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 16:59:59.14: [20065]: RECV training at v.17 7200 bit/s

Set 22 16:59:59.14: [20065]: <-- [10:AT+FRM=73\r]

Set 22 17:00:03.64: [20065]: --> [0:]

Set 22 17:00:03.64: [20065]: MODEM <Empty line>

Set 22 17:00:03.65: [20065]: <-- data [1]

Set 22 17:00:03.65: [20065]: --> [2:OK]

Set 22 17:00:03.65: [20065]: DELAY 70 ms

Set 22 17:00:03.72: [20065]: <-- [9:AT+FTH=3\r]

Set 22 17:00:03.97: [20065]: --> [7:CONNECT]

Set 22 17:00:03.97: [20065]: <-- data [3]

Set 22 17:00:03.97: [20065]: <-- data [2]

Set 22 17:00:05.18: [20065]: --> [2:OK]

Set 22 17:00:05.19: [20065]: TRAINING failed

Set 22 17:00:05.19: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:06.35: [20065]: --> [7:CONNECT]

Set 22 17:00:07.01: [20065]: --> [2:OK]

Set 22 17:00:07.01: [20065]: REMOTE TSI "236xxxxxx"

Set 22 17:00:07.01: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:07.05: [20065]: --> [7:CONNECT]

Set 22 17:00:07.45: [20065]: --> [2:OK]

Set 22 17:00:07.45: [20065]: REMOTE wants 4800 bit/s

Set 22 17:00:07.45: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 17:00:07.45: [20065]: REMOTE wants unlimited page length

Set 22 17:00:07.45: [20065]: REMOTE wants 3.85 line/mm

Set 22 17:00:07.45: [20065]: REMOTE wants 2-D MMR

Set 22 17:00:07.45: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 17:00:07.45: [20065]: RECV training at v.27ter 4800 bit/s

Set 22 17:00:07.45: [20065]: <-- [10:AT+FRM=48\r]

Set 22 17:00:08.54: [20065]: --> [7:CONNECT]

Set 22 17:00:10.07: [20065]: RECV: TCF 909 bytes, 2% non-zero, 422 zero-run

Set 22 17:00:10.07: [20065]: RECV: reject TCF (zero run too short, min 600)

Set 22 17:00:10.09: [20065]: --> [10:NO CARRIER]

Set 22 17:00:10.09: [20065]: DELAY 70 ms

Set 22 17:00:10.17: [20065]: <-- [9:AT+FTH=3\r]

Set 22 17:00:10.41: [20065]: --> [7:CONNECT]

Set 22 17:00:10.41: [20065]: <-- data [3]

Set 22 17:00:10.41: [20065]: <-- data [2]

Set 22 17:00:11.63: [20065]: --> [2:OK]

Set 22 17:00:11.63: [20065]: TRAINING failed

Set 22 17:00:11.63: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:12.79: [20065]: --> [7:CONNECT]

Set 22 17:00:13.46: [20065]: --> [2:OK]

Set 22 17:00:13.46: [20065]: REMOTE TSI "236xxxxxx"

Set 22 17:00:13.46: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:13.49: [20065]: --> [7:CONNECT]

Set 22 17:00:13.89: [20065]: --> [2:OK]

Set 22 17:00:13.89: [20065]: REMOTE wants 4800 bit/s

Set 22 17:00:13.89: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 17:00:13.89: [20065]: REMOTE wants unlimited page length

Set 22 17:00:13.89: [20065]: REMOTE wants 3.85 line/mm

Set 22 17:00:13.89: [20065]: REMOTE wants 2-D MMR

Set 22 17:00:13.89: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 17:00:13.89: [20065]: RECV training at v.27ter 4800 bit/s

Set 22 17:00:13.89: [20065]: <-- [10:AT+FRM=48\r]

Set 22 17:00:14.98: [20065]: --> [7:CONNECT]

Set 22 17:00:16.51: [20065]: RECV: TCF 909 bytes, 2% non-zero, 422 zero-run

Set 22 17:00:16.51: [20065]: RECV: reject TCF (zero run too short, min 600)

Set 22 17:00:16.54: [20065]: --> [10:NO CARRIER]

Set 22 17:00:16.54: [20065]: DELAY 70 ms

Set 22 17:00:16.61: [20065]: <-- [9:AT+FTH=3\r]

Set 22 17:00:16.86: [20065]: --> [7:CONNECT]

Set 22 17:00:16.86: [20065]: <-- data [3]

Set 22 17:00:16.86: [20065]: <-- data [2]

Set 22 17:00:18.07: [20065]: --> [2:OK]

Set 22 17:00:18.07: [20065]: TRAINING failed

Set 22 17:00:18.07: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:19.24: [20065]: --> [7:CONNECT]

Set 22 17:00:19.91: [20065]: --> [2:OK]

Set 22 17:00:19.91: [20065]: REMOTE TSI "236xxxxxx"

Set 22 17:00:19.91: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:19.94: [20065]: --> [7:CONNECT]

Set 22 17:00:20.35: [20065]: --> [2:OK]

Set 22 17:00:20.35: [20065]: REMOTE wants 2400 bit/s

Set 22 17:00:20.35: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 17:00:20.35: [20065]: REMOTE wants unlimited page length

Set 22 17:00:20.35: [20065]: REMOTE wants 3.85 line/mm

Set 22 17:00:20.35: [20065]: REMOTE wants 2-D MMR

Set 22 17:00:20.35: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 17:00:20.35: [20065]: RECV training at v.27ter fallback mode 2400 bit/s

Set 22 17:00:20.35: [20065]: <-- [10:AT+FRM=24\r]

Set 22 17:00:21.67: [20065]: --> [7:CONNECT]

Set 22 17:00:23.93: [20065]: RECV: TCF 672 bytes, 32% non-zero, 451 zero-run

Set 22 17:00:23.93: [20065]: RECV: reject TCF (too many non-zero, max 10%)

Set 22 17:00:23.96: [20065]: --> [10:NO CARRIER]

Set 22 17:00:23.96: [20065]: DELAY 70 ms

Set 22 17:00:24.03: [20065]: <-- [9:AT+FTH=3\r]

Set 22 17:00:24.27: [20065]: --> [7:CONNECT]

Set 22 17:00:24.27: [20065]: <-- data [3]

Set 22 17:00:24.27: [20065]: <-- data [2]

Set 22 17:00:25.49: [20065]: --> [2:OK]

Set 22 17:00:25.49: [20065]: TRAINING failed

Set 22 17:00:25.49: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:26.66: [20065]: --> [7:CONNECT]

Set 22 17:00:27.33: [20065]: --> [2:OK]

Set 22 17:00:27.33: [20065]: REMOTE TSI "236xxxxxx"

Set 22 17:00:27.33: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:27.36: [20065]: --> [7:CONNECT]

Set 22 17:00:27.77: [20065]: --> [2:OK]

Set 22 17:00:27.77: [20065]: REMOTE wants 2400 bit/s

Set 22 17:00:27.77: [20065]: REMOTE wants A4 page width (215 mm)

Set 22 17:00:27.77: [20065]: REMOTE wants unlimited page length

Set 22 17:00:27.77: [20065]: REMOTE wants 3.85 line/mm

Set 22 17:00:27.77: [20065]: REMOTE wants 2-D MMR

Set 22 17:00:27.77: [20065]: REMOTE wants T.30 Annex A, 256-byte ECM

Set 22 17:00:27.77: [20065]: RECV training at v.27ter fallback mode 2400 bit/s

Set 22 17:00:27.77: [20065]: <-- [10:AT+FRM=24\r]

Set 22 17:00:29.09: [20065]: --> [7:CONNECT]

Set 22 17:00:31.29: [20065]: RECV: TCF 654 bytes, 30% non-zero, 451 zero-run

Set 22 17:00:31.29: [20065]: RECV: reject TCF (too many non-zero, max 10%)

Set 22 17:00:31.31: [20065]: --> [10:NO CARRIER]

Set 22 17:00:31.31: [20065]: DELAY 70 ms

Set 22 17:00:31.39: [20065]: <-- [9:AT+FTH=3\r]

Set 22 17:00:31.63: [20065]: --> [7:CONNECT]

Set 22 17:00:31.63: [20065]: <-- data [3]

Set 22 17:00:31.63: [20065]: <-- data [2]

Set 22 17:00:32.85: [20065]: --> [2:OK]

Set 22 17:00:32.85: [20065]: TRAINING failed

Set 22 17:00:32.85: [20065]: <-- [9:AT+FRH=3\r]

Set 22 17:00:34.00: [20065]: --> [7:CONNECT]

Set 22 17:00:34.25: [20065]: --> [2:OK]

Set 22 17:00:34.25: [20065]: RECV FAX: RSPREC error/got DCN

Set 22 17:00:34.25: [20065]: RECV FAX: end

Set 22 17:00:34.25: [20065]: SESSION END

 

Can you please help? What more can I do?