Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine

To: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
Subject: Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
From: Herman Kuiper <herman@xxxxxxxxx>
Cc: hylafax-users@xxxxxxxxxxx
Date: Mon, 18 Aug 2008 11:38:10 +0200

Lee Howard wrote:

Herman Kuiper wrote:
Am receiving faxes, but one client of ours can't get through.
Seeing a session log would help us help you.

I wasn't sure if these would be appreciated unsollicited :-)

I've attached two examples. From memory the first one was "as-is", the second with the RecvCmd in the config file.

Herman

-------------------------------------------------------------------
Herman Kuiper  --  m: herman@xxxxxxxxx  --  w: http://www.ozuzo.net
Meerhuizenplein 10K - 1078 TC ASD - t: 020-6171885 - f: 020-6142816

Aug 12 16:12:20.83: [25427]: SESSION BEGIN 000000033 31206142816
Aug 12 16:12:20.83: [25427]: HylaFAX (tm) Version 4.4.3
Aug 12 16:12:20.83: [25427]: <-- [4:ATA\r]
Aug 12 16:12:26.47: [25427]: --> [7:CONNECT]
Aug 12 16:12:26.47: [25427]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyACM0'
Aug 12 16:12:26.47: [25427]: RECV FAX: begin
Aug 12 16:12:26.47: [25427]: <-- data [32]
Aug 12 16:12:26.47: [25427]: <-- data [2]
Aug 12 16:12:29.30: [25427]: --> [7:CONNECT]
Aug 12 16:12:29.30: [25427]: <-- data [23]
Aug 12 16:12:29.30: [25427]: <-- data [2]
Aug 12 16:12:30.07: [25427]: --> [7:CONNECT]
Aug 12 16:12:30.07: [25427]: <-- data [13]
Aug 12 16:12:30.07: [25427]: <-- data [2]
Aug 12 16:12:31.12: [25427]: --> [2:OK]
Aug 12 16:12:31.12: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:12:31.80: [25427]: --> [7:CONNECT]
Aug 12 16:12:33.63: [25427]: --> [2:OK]
Aug 12 16:12:33.63: [25427]: REMOTE TSI "0725764131"
Aug 12 16:12:33.63: [25427]: RECV recv TSI (sender id)
Aug 12 16:12:33.63: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:12:33.65: [25427]: --> [7:CONNECT]
Aug 12 16:12:33.65: [25427]: --> [2:OK]
Aug 12 16:12:33.65: [25427]: REMOTE wants 9600 bit/s
Aug 12 16:12:33.65: [25427]: REMOTE wants A4 page width (215 mm)
Aug 12 16:12:33.65: [25427]: REMOTE wants unlimited page length
Aug 12 16:12:33.65: [25427]: REMOTE wants 3.85 line/mm
Aug 12 16:12:33.65: [25427]: REMOTE wants 1-D MH
Aug 12 16:12:33.65: [25427]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 12 16:12:33.65: [25427]: RECV recv DCS (command signal)
Aug 12 16:12:33.65: [25427]: RECV training at v.29 9600 bit/s
Aug 12 16:12:33.65: [25427]: <-- [10:AT+FRM=96\r]
Aug 12 16:12:38.15: [25427]: --> [0:]
Aug 12 16:12:38.15: [25427]: MODEM <Empty line>
Aug 12 16:12:38.15: [25427]: <-- data [1]
Aug 12 16:12:38.16: [25427]: --> [2:OK]
Aug 12 16:12:38.16: [25427]: <-- [9:AT+FRS=7\r]
Aug 12 16:12:38.29: [25427]: --> [2:OK]
Aug 12 16:12:38.29: [25427]: <-- [9:AT+FTH=3\r]
Aug 12 16:12:38.34: [25427]: --> [7:CONNECT]
Aug 12 16:12:38.34: [25427]: <-- data [3]
Aug 12 16:12:38.34: [25427]: <-- data [2]
Aug 12 16:12:39.66: [25427]: --> [2:OK]
Aug 12 16:12:39.66: [25427]: TRAINING failed
Aug 12 16:12:39.66: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:12:45.84: [25427]: --> [7:CONNECT]
Aug 12 16:12:47.79: [25427]: --> [2:OK]
Aug 12 16:12:47.79: [25427]: REMOTE TSI "0725764131"
Aug 12 16:12:47.79: [25427]: RECV recv TSI (sender id)
Aug 12 16:12:47.79: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:12:47.80: [25427]: --> [7:CONNECT]
Aug 12 16:12:47.80: [25427]: --> [2:OK]
Aug 12 16:12:47.80: [25427]: REMOTE wants 9600 bit/s
Aug 12 16:12:47.80: [25427]: REMOTE wants A4 page width (215 mm)
Aug 12 16:12:47.80: [25427]: REMOTE wants unlimited page length
Aug 12 16:12:47.80: [25427]: REMOTE wants 3.85 line/mm
Aug 12 16:12:47.80: [25427]: REMOTE wants 1-D MH
Aug 12 16:12:47.80: [25427]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 12 16:12:47.80: [25427]: RECV recv DCS (command signal)
Aug 12 16:12:47.80: [25427]: RECV training at v.29 9600 bit/s
Aug 12 16:12:47.80: [25427]: <-- [10:AT+FRM=96\r]
Aug 12 16:12:52.30: [25427]: --> [0:]
Aug 12 16:12:52.30: [25427]: MODEM <Empty line>
Aug 12 16:12:52.30: [25427]: <-- data [1]
Aug 12 16:12:52.31: [25427]: --> [2:OK]
Aug 12 16:12:52.31: [25427]: <-- [9:AT+FRS=7\r]
Aug 12 16:12:52.44: [25427]: --> [2:OK]
Aug 12 16:12:52.44: [25427]: <-- [9:AT+FTH=3\r]
Aug 12 16:12:52.49: [25427]: --> [7:CONNECT]
Aug 12 16:12:52.49: [25427]: <-- data [3]
Aug 12 16:12:52.49: [25427]: <-- data [2]
Aug 12 16:12:53.80: [25427]: --> [2:OK]
Aug 12 16:12:53.80: [25427]: TRAINING failed
Aug 12 16:12:53.80: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:13:00.80: [25427]: --> [0:]
Aug 12 16:13:00.80: [25427]: MODEM <Empty line>
Aug 12 16:13:00.80: [25427]: <-- data [1]
Aug 12 16:13:00.85: [25427]: --> [2:OK]
Aug 12 16:13:00.85: [25427]: <-- [9:AT+FRS=7\r]
Aug 12 16:13:00.98: [25427]: --> [2:OK]
Aug 12 16:13:00.98: [25427]: <-- [9:AT+FTH=3\r]
Aug 12 16:13:01.02: [25427]: --> [7:CONNECT]
Aug 12 16:13:01.02: [25427]: <-- data [32]
Aug 12 16:13:01.02: [25427]: <-- data [2]
Aug 12 16:13:02.56: [25427]: --> [7:CONNECT]
Aug 12 16:13:02.56: [25427]: <-- data [23]
Aug 12 16:13:02.56: [25427]: <-- data [2]
Aug 12 16:13:03.33: [25427]: --> [7:CONNECT]
Aug 12 16:13:03.33: [25427]: <-- data [13]
Aug 12 16:13:03.33: [25427]: <-- data [2]
Aug 12 16:13:04.39: [25427]: --> [2:OK]
Aug 12 16:13:04.39: [25427]: <-- [9:AT+FRH=3\r]
Aug 12 16:13:11.39: [25427]: --> [0:]
Aug 12 16:13:11.39: [25427]: MODEM <Empty line>
Aug 12 16:13:11.39: [25427]: <-- data [1]
Aug 12 16:13:11.44: [25427]: --> [2:OK]
Aug 12 16:13:11.44: [25427]: RECV FAX: Failure to train modems
Aug 12 16:13:11.44: [25427]: RECV FAX: end
Aug 12 16:13:11.44: [25427]: Failure to train modems
Aug 12 16:13:11.44: [25427]: SESSION END

Aug 14 16:56:43.17: [10614]: SESSION BEGIN 000000040 31206142816
Aug 14 16:56:43.17: [10614]: HylaFAX (tm) Version 4.4.3
Aug 14 16:56:43.17: [10614]: <-- [4:ATA\r]
Aug 14 16:56:48.85: [10614]: --> [7:CONNECT]
Aug 14 16:56:48.85: [10614]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyACM0'
Aug 14 16:56:48.85: [10614]: RECV FAX: begin
Aug 14 16:56:48.93: [10614]: <-- data [32]
Aug 14 16:56:48.93: [10614]: <-- data [2]
Aug 14 16:56:51.67: [10614]: --> [7:CONNECT]
Aug 14 16:56:51.67: [10614]: <-- data [23]
Aug 14 16:56:51.67: [10614]: <-- data [2]
Aug 14 16:56:52.44: [10614]: --> [7:CONNECT]
Aug 14 16:56:52.44: [10614]: <-- data [13]
Aug 14 16:56:52.44: [10614]: <-- data [2]
Aug 14 16:56:53.49: [10614]: --> [2:OK]
Aug 14 16:56:53.49: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:56:54.18: [10614]: --> [7:CONNECT]
Aug 14 16:56:56.01: [10614]: --> [2:OK]
Aug 14 16:56:56.01: [10614]: REMOTE TSI "0725764131"
Aug 14 16:56:56.01: [10614]: RECV recv TSI (sender id)
Aug 14 16:56:56.01: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:56:56.02: [10614]: --> [7:CONNECT]
Aug 14 16:56:56.03: [10614]: --> [2:OK]
Aug 14 16:56:56.03: [10614]: REMOTE wants 9600 bit/s
Aug 14 16:56:56.03: [10614]: REMOTE wants A4 page width (215 mm)
Aug 14 16:56:56.03: [10614]: REMOTE wants unlimited page length
Aug 14 16:56:56.03: [10614]: REMOTE wants 3.85 line/mm
Aug 14 16:56:56.03: [10614]: REMOTE wants 1-D MH
Aug 14 16:56:56.03: [10614]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 14 16:56:56.03: [10614]: RECV recv DCS (command signal)
Aug 14 16:56:56.03: [10614]: <-- [9:AT+FRS=1\r]
Aug 14 16:56:56.09: [10614]: --> [2:OK]
Aug 14 16:56:56.09: [10614]: RECV training at v.29 9600 bit/s
Aug 14 16:56:56.09: [10614]: <-- [10:AT+FRM=96\r]
Aug 14 16:57:00.59: [10614]: --> [0:]
Aug 14 16:57:00.59: [10614]: MODEM <Empty line>
Aug 14 16:57:00.59: [10614]: <-- data [1]
Aug 14 16:57:00.60: [10614]: --> [2:OK]
Aug 14 16:57:00.60: [10614]: <-- [9:AT+FRS=7\r]
Aug 14 16:57:00.72: [10614]: --> [2:OK]
Aug 14 16:57:00.72: [10614]: <-- [9:AT+FTH=3\r]
Aug 14 16:57:00.78: [10614]: --> [7:CONNECT]
Aug 14 16:57:00.78: [10614]: <-- data [3]
Aug 14 16:57:00.78: [10614]: <-- data [2]
Aug 14 16:57:02.10: [10614]: --> [2:OK]
Aug 14 16:57:02.10: [10614]: TRAINING failed
Aug 14 16:57:02.10: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:57:08.22: [10614]: --> [7:CONNECT]
Aug 14 16:57:10.15: [10614]: --> [2:OK]
Aug 14 16:57:10.15: [10614]: REMOTE TSI "0725764131"
Aug 14 16:57:10.15: [10614]: RECV recv TSI (sender id)
Aug 14 16:57:10.15: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:57:10.16: [10614]: --> [7:CONNECT]
Aug 14 16:57:10.17: [10614]: --> [2:OK]
Aug 14 16:57:10.17: [10614]: REMOTE wants 9600 bit/s
Aug 14 16:57:10.17: [10614]: REMOTE wants A4 page width (215 mm)
Aug 14 16:57:10.17: [10614]: REMOTE wants unlimited page length
Aug 14 16:57:10.17: [10614]: REMOTE wants 3.85 line/mm
Aug 14 16:57:10.17: [10614]: REMOTE wants 1-D MH
Aug 14 16:57:10.17: [10614]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 14 16:57:10.17: [10614]: RECV recv DCS (command signal)
Aug 14 16:57:10.17: [10614]: <-- [9:AT+FRS=1\r]
Aug 14 16:57:10.23: [10614]: --> [2:OK]
Aug 14 16:57:10.23: [10614]: RECV training at v.29 9600 bit/s
Aug 14 16:57:10.23: [10614]: <-- [10:AT+FRM=96\r]
Aug 14 16:57:14.73: [10614]: --> [0:]
Aug 14 16:57:14.73: [10614]: MODEM <Empty line>
Aug 14 16:57:14.73: [10614]: <-- data [1]
Aug 14 16:57:14.74: [10614]: --> [2:OK]
Aug 14 16:57:14.74: [10614]: <-- [9:AT+FRS=7\r]
Aug 14 16:57:14.86: [10614]: --> [2:OK]
Aug 14 16:57:14.86: [10614]: <-- [9:AT+FTH=3\r]
Aug 14 16:57:14.93: [10614]: --> [7:CONNECT]
Aug 14 16:57:14.93: [10614]: <-- data [3]
Aug 14 16:57:14.93: [10614]: <-- data [2]
Aug 14 16:57:16.25: [10614]: --> [2:OK]
Aug 14 16:57:16.25: [10614]: TRAINING failed
Aug 14 16:57:16.25: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:57:23.25: [10614]: --> [0:]
Aug 14 16:57:23.25: [10614]: MODEM <Empty line>
Aug 14 16:57:23.25: [10614]: <-- data [1]
Aug 14 16:57:23.30: [10614]: --> [2:OK]
Aug 14 16:57:23.30: [10614]: <-- [9:AT+FRS=7\r]
Aug 14 16:57:23.42: [10614]: --> [2:OK]
Aug 14 16:57:23.42: [10614]: <-- [9:AT+FTH=3\r]
Aug 14 16:57:23.48: [10614]: --> [7:CONNECT]
Aug 14 16:57:23.48: [10614]: <-- data [32]
Aug 14 16:57:23.48: [10614]: <-- data [2]
Aug 14 16:57:25.03: [10614]: --> [7:CONNECT]
Aug 14 16:57:25.03: [10614]: <-- data [23]
Aug 14 16:57:25.03: [10614]: <-- data [2]
Aug 14 16:57:25.80: [10614]: --> [7:CONNECT]
Aug 14 16:57:25.80: [10614]: <-- data [13]
Aug 14 16:57:25.80: [10614]: <-- data [2]
Aug 14 16:57:26.86: [10614]: --> [2:OK]
Aug 14 16:57:26.86: [10614]: <-- [9:AT+FRH=3\r]
Aug 14 16:57:33.86: [10614]: --> [0:]
Aug 14 16:57:33.86: [10614]: MODEM <Empty line>
Aug 14 16:57:33.86: [10614]: <-- data [1]
Aug 14 16:57:33.91: [10614]: --> [2:OK]
Aug 14 16:57:33.91: [10614]: RECV FAX: Failure to train modems
Aug 14 16:57:33.91: [10614]: RECV FAX: end
Aug 14 16:57:33.91: [10614]: Failure to train modems
Aug 14 16:57:33.91: [10614]: SESSION END

Follow-Ups:
- Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
  - From: Lee Howard

References:
- [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
  - From: Herman Kuiper
- Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] Sendmail PDF Attachment
Next by Date: Re: [hylafax-users] Sendmail PDF Attachment
Previous by thread: Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
Next by thread: Re: [hylafax-users] Trying to get ACM modem to talk to Brother faxmachine
Index(es):
- Main
- Thread

Project hosted by iFAX Solutions