[hylafax-users] Hylafax + iaxmodem + abilis

["Andrea Scarso" <andrea.scarso@xxxxxxxxx>]

Hi all,
I'm trying to use Hylafax with iaxmodem both on a debian server, and
an Abilis as PBX.
http://www.abilis.net/fileadmin/tutorial/en/index.php

This is my /etc/iaxmodem/ttyIAX0:
device /dev/ttyIAX0
owner uucp:uucp
mode 660
port 4569
refresh 300
server XXX.XXX.XXX.XXX
peername hylafax01
secret 123456
cidname Fax1
cidnumber 00390444******
codec alaw

And this is my /var/spool/hylafax/etc/config.ttyIAX0
CountryCode:            39
AreaCode:               0444
FAXNumber:              ""
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules.europe
ServerTracing:          0xFFF
SessionTracing:         0xFFF
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "IAXmodem0"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           600
ModemType:              Class1          # use this to supply a hint
ModemResetCmds:         "ATH1\nAT+VCID=1"       # enables CallID display
ModemReadyCmds:         ATH0
Class1AdaptRecvCmd:     AT+FAR=1
Class1TMConnectDelay:   400             # counteract quick CONNECT response
Class1RMQueryCmd:       "!24,48,72,96"  # V.17 fast-train recv doesn't workwell
CallIDPattern:          "NMBR="
CallIDPattern:          "NAME="
CallIDPattern:          "ANID="
CallIDPattern:          "NDID="
Class1JBIGSupport:       no


This is my IAX user:
[09:41:33] ABILIS:_d user:hylafax01

Parameter:        | Value:
------------------+------------------------------------------------------------
USER:               hylafax01
PWD:                ***
ACT:                YES
IAX:                YES
IAX-HOST:           XXX.XXX.XXX.XXX
IAX-SRCADD:         SYS
IAX-PORT:           4569
IAX-IP-PERMIT:      *
IAX-MAXSES-BID:     2
IAX-MAXSES-IN:      0
IAX-MAXSES-OUT:     0
IAX-NUMBER:         444XXXXXX
IAX-CG-NUM:         AUTO
IAX-FWD-CG-NUM:     CALLER
IAX-ROUTE-BY-SD:    NO
IAX-PROVIDE-SG:     NO
IAX-CLIP-RULE:      SYS
IAX-CONTEXT:
IAX-PROVIDE-NAME:   BLANK
IAX-AUTH:           SYS
IAX-NETSTATS:       SYS
IAX-TRUNK:          SYS
IAX-TRUNK-FREQ:     SYS
IAX-CHAN-FREQ:      SYS
IAX-CPO:            SYS
IAX-CPO-STATE:      SYS
IAX-CPO-DROP:       SYS
IAX-TRANSFER:       SYS
IAX-DISC-AUDIO:     SYS
IAX-HTML-IN:        SYS
IAX-HTML-OUT:       SYS
IAX-REM-USER:       hylafax01
IAX-REM-PASS:       *********
IAX-REM-AUTH:       SYS
IAX-REM-REG:        NO
-------------------------------------------------------------------------------

http://www.abilis.net/fileadmin/tutorial/en/ch27s02.php#ch.iax2.users



It seems everything ok: iaxmodem registers to Abilis, hylafax
recognize ttyIAX0, but when I try to send a fax this is the result:

lug 28 18:06:59.36: [ 4820]: SESSION BEGIN 000000009 39444XXXXXX
lug 28 18:06:59.36: [ 4820]: HylaFAX (tm) Version 4.3.1
lug 28 18:06:59.36: [ 4820]: SEND FAX: JOB 16 DEST 0444XXXXXX COMMID
000000009 DEVICE '/dev/ttyIAX0' FROM 'xxx <xxx@xxxxxx>' USER faxmaster
lug 28 18:06:59.36: [ 4820]: STATE CHANGE: RUNNING -> SENDING
lug 28 18:06:59.36: [ 4820]: <-- [12:AT+FCLASS=1\r]
lug 28 18:06:59.36: [ 4820]: --> [2:OK]
lug 28 18:06:59.36: [ 4820]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
lug 28 18:06:59.36: [ 4820]: DIAL 0444XXXXXX
lug 28 18:06:59.36: [ 4820]: <-- [15:ATDT0444XXXXXX\r]
lug 28 18:07:46.51: [ 4820]: --> [10:NO CARRIER]
lug 28 18:07:46.51: [ 4820]: SEND FAILED: JOB 16 DEST 0444XXXXXX ERR
No carrier detected
lug 28 18:07:46.51: [ 4820]: <-- [5:ATH0\r]
lug 28 18:07:46.51: [ 4820]: --> [2:OK]
lug 28 18:07:46.51: [ 4820]: MODEM set DTR OFF
lug 28 18:07:46.51: [ 4820]: MODEM set baud rate: 0 baud (flow control
unchanged)
lug 28 18:07:46.51: [ 4820]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
lug 28 18:07:46.51: [ 4820]: SESSION END

On the other side, when I try to call this fax with another fax, this
is the result on the other fax:

lug 28 18:06:06.12: [ 6335]: SESSION BEGIN 000005552 +39444XXXXXX
lug 28 18:06:06.12: [ 6335]: HylaFAX (tm) Version 5.1.11
lug 28 18:06:06.12: [ 6335]: SEND FAX: JOB 1471 DEST 0444XXXXXX COMMID
000005552 DEVICE '/dev/ttyS0' FROM 'xxx <xxx@xxxxxx>' USER fax
lug 28 18:06:06.12: [ 6335]: <-- [9:AT+FLO=2\r]
lug 28 18:06:06.13: [ 6335]: --> [2:OK]
lug 28 18:06:06.13: [ 6335]: <-- [9:AT+FPP=0\r]
lug 28 18:06:06.14: [ 6335]: --> [2:OK]
lug 28 18:06:06.14: [ 6335]: <-- [9:AT+FBO=0\r]
lug 28 18:06:06.15: [ 6335]: --> [2:OK]
lug 28 18:06:06.15: [ 6335]: <-- [10:AT+FCT=30\r]
lug 28 18:06:06.16: [ 6335]: --> [2:OK]
lug 28 18:06:06.16: [ 6335]: <-- [11:AT+FCQ=2,2\r]
lug 28 18:06:06.18: [ 6335]: --> [2:OK]
lug 28 18:06:06.18: [ 6335]: <-- [15:AT+FNR=1,1,1,1\r]
lug 28 18:06:06.19: [ 6335]: --> [2:OK]
lug 28 18:06:06.19: [ 6335]: <-- [9:AT+FIE=0\r]
lug 28 18:06:06.20: [ 6335]: --> [2:OK]
lug 28 18:06:06.20: [ 6335]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
lug 28 18:06:06.23: [ 6335]: --> [2:OK]
lug 28 18:06:06.23: [ 6335]: DIAL 0444XXXXXX
lug 28 18:06:06.23: [ 6335]: <-- [15:ATDT0444XXXXXX\r]
lug 28 18:06:14.48: [ 6335]: --> [4:BUSY]
lug 28 18:06:14.48: [ 6335]: SEND FAILED: JOB 1471 DEST 0444XXXXXX ERR
Busy signal detected {E001}
lug 28 18:06:14.48: [ 6335]: SEND FAILED: JOB 1471 DEST 0444XXXXXX ERR
Busy signal detected {E001}; too many attempts to dial
lug 28 18:06:15.49: [ 6335]: <-- [5:ATH0\r]
lug 28 18:06:15.49: [ 6335]: --> [2:OK]
lug 28 18:06:15.49: [ 6335]: SESSION END


I understand Abilis is not wide spread, but do you understand if I
have to work on hylafax, iaxmodem or abilis to solve the problem?
On which device do you think the problem is?

If it can be useful, I tried to record the iaxmodem raw file, and I
hear the tipical modem sounds on background, but there are other very
loud disturbing sounds.. is this normal?

Thanks,
Andrea


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*