[hylafax-users] Caller ID with a external Hayes Accura V.92 Model H08-15328-C

["dwalker@xxxxxxxxxxxxx" <dwalker@xxxxxxxxxxxxx>]

Hello Everyone,

I have read extensively the List for setting up
caller ID. We are using Hylafax 4.4.4 using the
Accura Conexant chipset. I made sure that the call id
information was being sent to the device by attaching
a phone and watching the info pass to it. Below is
the ttyS0 config and the log associated with the
call. I have read the manufactures site as well as
similiar setups on the list. Can anyone give advice
on what I could do to find out why the info is not
being passed.

ttys0 config:

CountryCode:		1
AreaCode:		xxx
FAXNumber:		xxx.xxx
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	3
ModemResetCmds:	        AT+VCID=1
CallIDPattern:	        "NMBR="
CallIDPattern:	        "NAME="
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	xxxFAX
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
FaxRcvdCmd:		bin/faxrcvd.php
NotifyCmd:		bin/notify.php
#
#
# Modem-related stuff: should reflect modem command
interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects
carrier (or not)
#
ModemMfrQueryCmd:	!Rockwell
ModemModelQueryCmd:	!RC288DPi
ModemRevQueryCmd:	ATI3		# product information
#
ModemDialCmd:		ATDT%s		# T for tone dialing


Log of the call:

[ 2565]: SESSION BEGIN 000000039 1xxxxxxxxxx
[ 2565]: HylaFAX (tm) Version 4.4.4
[ 2565]: <-- [4:ATA\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
[ 2565]: RECV FAX: begin
[ 2565]: <-- data [32]
[ 2565]: <-- data [2]
[ 2565]: --> [7:CONNECT]
[ 2565]: <-- data [23]
[ 2565]: <-- data [2]
[ 2565]: --> [7:CONNECT]
[ 2565]: <-- data [13]
[ 2565]: <-- data [2]
[ 2565]: --> [2:OK]
[ 2565]: <-- [9:AT+FRH=3\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: --> [2:OK]
[ 2565]: REMOTE wants 14400 bit/s
[ 2565]: REMOTE wants A4 page width (215 mm)
[ 2565]: REMOTE wants unlimited page length
[ 2565]: REMOTE wants 3.85 line/mm
[ 2565]: REMOTE wants 2-D MMR
[ 2565]: REMOTE wants T.30 Annex A, 256-byte ECM
[ 2565]: RECV recv DCS (command signal)
[ 2565]: RECV training at v.17 14400 bit/s
[ 2565]: <-- [11:AT+FRM=145\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: RECV: TCF 2753 bytes, 1% non-zero, 2702 zero-run
[ 2565]: --> [10:NO CARRIER]
[ 2565]: <-- [9:AT+FRS=7\r]
[ 2565]: --> [2:OK]
[ 2565]: TRAINING succeeded
[ 2565]: <-- [9:AT+FTH=3\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: <-- data [3]
[ 2565]: <-- data [2]
[ 2565]: --> [2:OK]
[ 2565]: <-- [11:AT+FRM=146\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: RECV received frame number 0
[ 2565]: RECV received frame number 1
[ 2565]: RECV received frame number 2
[ 2565]: RECV received RCP frame
[ 2565]: --> [10:NO CARRIER]
 2565]: <-- [9:AT+FRH=3\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: --> [2:OK]
[ 2565]: RECV recv PPS (partial page signal)
[ 2565]: RECV recv EOP (no more pages or documents)
[ 2565]: RECV received 3 frames of block 1 of page 1
[ 2565]: RECV: 713 bytes of data, 1048 total lines
[ 2565]: <-- [9:AT+FRS=7\r]
[ 2565]: --> [2:OK]
[ 2565]: <-- [9:AT+FTH=3\r]
[ 2565]: --> [7:CONNECT]
[ 2565]: <-- data [3]
[ 2565]: <-- data [2]
[ 2565]: --> [2:OK]
[ 2565]: RECV send MCF (message confirmation)
[ 2565]: RECV FAX (000000039): from <UNSPECIFIED>,
page 1 in 0:15, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s
Jul 17 19:49:03.66: [ 2565]: RECV FAX (000000039):
recvq/fax000000019.tif from <UNSPECIFIED>, route to
<unspecified>, 1 pages in 0:16
[ 2565]: <-- [9:AT+FRH=3\r]
 2565]: --> [7:CONNECT]
[ 2565]: --> [2:OK]
[ 2565]: RECV recv DCN (disconnect)
[ 2565]: RECV FAX: bin/faxrcvd.php
"recvq/fax000000019.tif" "ttyS0" "000000039" ""
[ 2565]: RECV FAX: end
[ 2565]: SESSION END



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*