[hylafax-users] Cannot send faxes to remote devices

[madalin mihaila <madalin@xxxxxxxxxxxxx>]

Hi all,
I have a problem with a HylaFax server configuration and I need your help. Every time I want to send a fax to a remote device, the communication with my server is closed shortly after the connection is made.
I made several tests with 3 different devices, but the result is the same.
During the tests, I saw that I cannot send faxes to remote devices, but I can receive them from the same devices.
I'm using CentOS 5, HylaFax 4.4.4-1, Winprint, internal modem (Intel 536ep chipset) with drivers from linmodems.
 
ls -l /dev/modem
lrwxrwxrwx 1 root root 10 Jun 24 13:42 /dev/modem -> /dev/536ep

ls -l /dev/536*
crw------- 1 uucp root 240, 1 Jun 24 13:42 /dev/536ep
crw------- 1 root root 240, 1 Jun 24 13:42 /dev/536ep0

joe /etc/inittab
..
mo:2345:respawn:/usr/sbin/faxgetty modem

joe /var/spool/hylafax/etc/config.modem
 
CountryCode:            40
AreaCode:               244
FAXNumber:              0344XXXXXX
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          high
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        Fax
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
 
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemSetupDCDCmd:       AT&C1           # setup so DCD follows carrier
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before EOP
Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and trans
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

 

Session log

 
---- Transcript of session follows ----

Jun 20 13:25:24.16: [ 2226]: SESSION BEGIN 000000024 40244XXXXXX
Jun 20 13:25:24.16: [ 2226]: HylaFAX (tm) Version 4.4.4
Jun 20 13:25:24.16: [ 2226]: SEND FAX: JOB 10 DEST 0244XXXXXX COMMID 000000024 DEVICE '/dev/modem' FROM 'root <root>' USER root
Jun 20 13:25:24.16: [ 2226]: <-- [12:AT+FCLASS=1\r]
Jun 20 13:25:24.23: [ 2226]: --> [2:OK]
Jun 20 13:25:24.23: [ 2226]: DIAL 0244XXXXXX
Jun 20 13:25:24.23: [ 2226]: <-- [15:ATDT0244XXXXXX\r]
Jun 20 13:25:40.15: [ 2226]: --> [7:CONNECT]
Jun 20 13:25:42.24: [ 2226]: --> [2:OK]
Jun 20 13:25:42.24: [ 2226]: REMOTE NSF "00 00 11 80 00 8A 49 10 43 4F 4E 54 52 4F 4C 20 54 52 41 44 49 4E 47 20 00 7D 00 80 80 80 02 01 01"
Jun 20 13:25:42.24: [ 2226]: NSF remote fax equipment: Canon Laser Class 9000 Series
Jun 20 13:25:42.24: [ 2226]: NSF remote station ID: "FAX "
Jun 20 13:25:42.24: [ 2226]: <-- [9:AT+FRH=3\r]
Jun 20 13:25:42.30: [ 2226]: --> [7:CONNECT]
Jun 20 13:25:42.94: [ 2226]: --> [2:OK]
Jun 20 13:25:42.94: [ 2226]: REMOTE CSI "40244XXXXXX"
Jun 20 13:25:42.94: [ 2226]: <-- [9:AT+FRH=3\r]
Jun 20 13:25:43.00: [ 2226]: --> [7:CONNECT]
Jun 20 13:25:43.27: [ 2226]: --> [2:OK]
Jun 20 13:25:43.27: [ 2226]: REMOTE best rate 14400 bit/s
Jun 20 13:25:43.27: [ 2226]: REMOTE max A4 page width (215 mm)
Jun 20 13:25:43.27: [ 2226]: REMOTE max unlimited page length
Jun 20 13:25:43.27: [ 2226]: REMOTE best vres 15.4 line/mm
Jun 20 13:25:43.27: [ 2226]: REMOTE format support: MH, MR, MMR
Jun 20 13:25:43.27: [ 2226]: REMOTE supports T.30 Annex A, 256-byte ECM
Jun 20 13:25:43.27: [ 2226]: REMOTE best 10 ms/scanline
Jun 20 13:25:43.27: [ 2226]: USE 14400 bit/s
Jun 20 13:25:43.27: [ 2226]: USE error correction mode
Jun 20 13:25:43.27: [ 2226]: <-- [9:AT+FRS=7\r]
Jun 20 13:25:43.34: [ 2226]: --> [2:OK]
Jun 20 13:25:43.34: [ 2226]: <-- [9:AT+FTH=3\r]
Jun 20 13:25:43.41: [ 2226]: --> [7:CONNECT]
Jun 20 13:25:43.41: [ 2226]: <-- data [3]
Jun 20 13:25:43.41: [ 2226]: <-- data [2]
Jun 20 13:25:44.65: [ 2226]: --> [2:OK]
Jun 20 13:25:45.65: [ 2226]: <-- [5:ATH0\r]
Jun 20 13:25:46.20: [ 2226]: --> [2:OK]
Jun 20 13:25:46.20: [ 2226]: SESSION END

------- Unsent job status -------
  Destination: 0244XXXXXX
           JobID: 10
         GroupID: 10
          Sender: root
        Mailaddr: root
          CommID: 000000024
           Modem: any
  Submitted From: 192.168.0.13
      Page Width: 0  (mm)
     Page Length: 0 (mm)
      Resolution: 196 (lpi)
          Status:
         Dialogs: 1
           Dials: 0
           Calls: 1
           Pages: 0
        TotPages: 0
        Attempts: 0
          Dirnum:

Thanks,

__
Madalin

____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*