Re: [hylafax-users] Sending Faxes

["kent" <kent@xxxxxxxxxxxxxx>]

Hi Chris,

You were right, it was the phone line.  I used a different line for outgoing
and it works fine.

Thanks for the tip!

Kent
 

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Chris Weiss
Sent: Thursday, May 15, 2008 8:24 AM
To: KENT
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Sending Faxes


On Thu, May 15, 2008 at 10:16 AM, KENT <kent@xxxxxxxxxxxxxx> wrote:


	Hi,
	
	I have been using hylafax for years to receiving faxes, and haven't
used it
	in a long time for sending anything.  But I'm getting an email to
fax
	service set up, so that @fax.mydomain.com emails get sent to hylafax
and am
	trying to set it up for outgoing again.  I
	set that up fairly easily, using this link
	http://hylafax.sourceforge.net/howto/faxing.php#ss5.4 (using
postfix) and it
	sends jobs to hylafax.
	
	The issue is that hylafax wouldn't send any fax at all.... It would
	reinitialize the modem after a few seconds (maybe 5 or 10) and then
requeue
	the message.  So I installed WHFC and tried to send a fax that
way... And
	got the same result.
	
	the issue seems to be that it thinks there is a busy signal so the
fax job
	is requeued... even thought the destination fax number is not busy
(it is on
	the same machine, it is one of the incoming fax lines and I know it
isn't
	busy by doing a faxstat).  Faxstat shows the initialization of the
outgoing
	fax modem on ttyS2 (I have set MaxRecvPages: 0 on this fax machine
so I it
	is outgoing only, and the other fax modems ttyS0,1,and 3 are set to
	ModemReadyState: D so that they are receive only) and then the ttyS2
modem
	starts to send the job.  But the other fax modem I am receiving the
tests on
	do not receive or even pick up... so the sending modem cannot be
receiving a
	busy signal...  Any insight would be greatly appreciated.
	
	Here is the message in the message log:
	
	[root@emailserver ~]# tail /var/log/messages
	May 15 07:54:50 emailserver FaxQueuer[32129]: NOTIFY: bin/notify
"doneq/q10"
	"failed" "0:27"
	
	May 15 07:54:50 emailserver FaxQueuer[32129]: BATCH to +16044343036
done
	after 2 jobs
	
	May 15 07:54:50 emailserver FaxGetty[32139]: LOCKWAIT
	
	May 15 07:54:50 emailserver FaxQueuer[32129]: NOTIFY exit status: 0
(1277)
	
	May 15 07:54:59 emailserver FaxSend[1278]: MODEM V2.400B-V90_2M_DLS
	MT5600ZDX/
	
	May 15 07:55:00 emailserver FaxSend[1278]: SEND FAX: JOB 11 DEST
1604xxxxxxx
	COMMID 000010822 DEVICE '/dev/ttyS2' FROM 'kent <kent>' USER kent
	
	May 15 07:55:16 emailserver FaxSend[1278]: SEND FAILED: JOB 11 DEST
	1604xxxxxxx ERR [1] Busy signal detected
	
	May 15 07:55:17 emailserver FaxQueuer[32129]: NOTIFY: bin/notify
"sendq/q11"
	"requeued" "" "07:58"
	
	May 15 07:55:17 emailserver FaxQueuer[32129]: NOTIFY exit status: 0
(1372)
	
	May 15 07:55:28 emailserver FaxGetty[32139]: MODEM
V2.400B-V90_2M_DLS
	MT5600ZDX/
	
	
	
	And in /etc/hylafax/logs the message for the job is:
	
	May 15 07:55:00.15: [ 1278]: SESSION BEGIN 000010822 1604xxxxxxx
	
	May 15 07:55:00.15: [ 1278]: HylaFAX (tm) Version 4.4.2
	
	May 15 07:55:00.15: [ 1278]: SEND FAX: JOB 11 DEST 1604xxxxxxx
COMMID
	000010822 DEVICE '/dev/ttyS2' FROM 'kent <kent>' USER kent
	
	May 15 07:55:00.15: [ 1278]: <-- [14:AT+FCLASS=1.0\r]
	
	May 15 07:55:00.17: [ 1278]: --> [2:OK]
	
	May 15 07:55:00.17: [ 1278]: DIAL 1604xxxxxxx
	
	May 15 07:55:00.17: [ 1278]: <-- [16:ATDT16044343036\r]
	
	May 15 07:55:16.20: [ 1278]: --> [4:BUSY]
	
	May 15 07:55:16.20: [ 1278]: SEND FAILED: JOB 11 DEST 1604xxxxxxx
ERR [1]
	Busy signal detected
	
	May 15 07:55:17.21: [ 1278]: <-- [5:ATH0\r]
	
	May 15 07:55:17.22: [ 1278]: --> [2:OK]
	
	May 15 07:55:17.22: [ 1278]: SESSION END
	
	Thanks,
	
	Kent
	
	
	

can you plug a phone into that line and dial out?  says it's busy, so maybe
the line isn't allowed to dial out


--
This message has been scanned for viruses and dangerous content by
MailScanner <http://www.mailscanner.info/> , and is believed to be clean. 


-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*