[hylafax-users] Problem receiving faxes....

["Alekos Avgoustatos" <alekos.avgoustatos@xxxxxxxxx>]

Hello.

After trying and googling for 2 days now I try to get some help from you because I cant find the solution.
I have set up hylafax on centos, everything works. But when someone sends a fax, I get this error: (one of my log files)....

y 09 14:29:58.05: [ 2826]: REMOTE wants 14400 bit/s
May 09 14:29:58.05: [ 2826]: REMOTE wants A4 page width (215 mm)
May 09 14:29:58.05: [ 2826]: REMOTE wants unlimited page length
May 09 14:29:58.05: [ 2826]: REMOTE wants 3.85 line/mm
May 09 14:29:58.05: [ 2826]: REMOTE wants 2-D MMR
May 09 14:29:58.05: [ 2826]: REMOTE wants T.30 Annex A, 256-byte ECM
May 09 14:29:58.05: [ 2826]: RECV recv DCS (command signal)
May 09 14:29:58.05: [ 2826]: RECV training at v.17 14400 bit/s
May 09 14:29:58.05: [ 2826]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
May 09 14:29:58.05: [ 2826]: <-- [11:AT+FRM=145\r]
May 09 14:30:02.55: [ 2826]: --> [0:]
May 09 14:30:02.55: [ 2826]: MODEM <Empty line>
May 09 14:30:02.55: [ 2826]: MODEM TIMEOUT: receiving TCF
May 09 14:30:02.55: [ 2826]: <-- data [1]
May 09 14:30:02.57: [ 2826]: --> [2:OK]
May 09 14:30:02.57: [ 2826]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
May 09 14:30:02.57: [ 2826]: DELAY 70 ms
May 09 14:30:02.64: [ 2826]: <-- [9:AT+FTH=3\r]
May 09 14:30:02.65: [ 2826]: --> [7:CONNECT]
May 09 14:30:02.65: [ 2826]: <-- HDLC<3:FF C8 22>
May 09 14:30:02.65: [ 2826]: <-- data [3]
May 09 14:30:02.65: [ 2826]: <-- data [2]
May 09 14:30:03.73: [ 2826]: --> [2:OK]
May 09 14:30:03.73: [ 2826]: TRAINING failed
May 09 14:30:03.73: [ 2826]: <-- [9:AT+FRH=3\r]
May 09 14:30:06.75: [ 2826]: --> [7:CONNECT]
May 09 14:30:10.55: [ 2826]: --> HDLC<114:FF FF FF FF FF 3F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3F 00 00 00 00 C0 C2 1C 2C 0C 04 0C 0C 1C 04 0C 0C 1C 0C 0C 04 04 04 04 04 04 04 7D F0>
May 09 14:30:10.55: [ 2826]: --> [5:ERROR]
May 09 14:30:10.55: [ 2826]: MODEM Command error
May 09 14:30:10.55: [ 2826]: FCS error
May 09 14:30:10.55: [ 2826]: DELAY 70 ms
May 09 14:30:10.62: [ 2826]: <-- [9:AT+FTH=3\r]
May 09 14:30:10.63: [ 2826]: --> [7:CONNECT]
May 09 14:30:10.63: [ 2826]: <-- HDLC<3:FF C8 58>
May 09 14:30:10.63: [ 2826]: <-- data [3]
May 09 14:30:10.63: [ 2826]: <-- data [2]
May 09 14:30:11.71: [ 2826]: --> [2:OK]
May 09 14:30:11.71: [ 2826]: RECV send CRP (command repeat)
May 09 14:30:11.71: [ 2826]: <-- [9:AT+FRH=3\r]
May 09 14:30:13.83: [ 2826]: --> [7:CONNECT]
May 09 14:30:15.99: [ 2826]: --> [2:10 03]
May 09 14:30:15.99: [ 2826]: --> [10:NO CARRIER]
May 09 14:30:15.99: [ 2826]: MODEM No carrier
May 09 14:30:15.99: [ 2826]: DELAY 70 ms
May 09 14:30:16.06: [ 2826]: <-- [9:AT+FTH=3\r]
May 09 14:30:16.06: [ 2826]: --> [5:ERROR]
May 09 14:30:16.06: [ 2826]: RECV FAX: RSPREC error/got EOT
May 09 14:30:16.06: [ 2826]: RECV FAX: end
May 09 14:30:16.06: [ 2826]: RSPREC error/got EOT
May 09 14:30:16.06: [ 2826]: SESSION END

I tried to change codec, I changed speed to 14400 / 9600, but nothing helps... any ideas ?
Regards and thank you in advance
Alekos