 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] No response to PPS repeated 3 times.:
- To: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>
- Subject: Re: [hylafax-users] No response to PPS repeated 3 times.:
- From: "CS Linux Support Group" <cslinux@xxxxxxxxxx>
- Cc: "CS Linux Support Group" <cslinux@xxxxxxxxxx>, hylafax-users@xxxxxxxxxxx
- Reply-to: cslinux@xxxxxxxxxx
- Date: Sat, 2 Feb 2008 02:07:17 -0500 (EST)
Hi Lee, Here's the log I received when I tried sending the fax to the same receiver. ModemSoftRTFCC option wasn't specified in the modem config file. The command used was sendfax -f "emailid" -R -r "faxsubject" -c "coverpage comments" -x "Recipient's company" -d "54640" ~/output.ps Thank you, Aravindan -------------------------------------------------------------------------- > No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page > ---- Transcript of session follows ---- > Jan 22 16:13:32.66: [11552]: SESSION BEGIN 000000097 121254640 > Jan 22 16:13:32.66: [11552]: HylaFAX (tm) Version 4.4.2 > Jan 22 16:13:32.66: [11552]: SEND FAX: JOB 59 DEST 54640 COMMID 000000097 DEVICE '/dev/ttyS0' FROM 'acase <acase@xxxxxxxxxxxx>' USER acase > Jan 22 16:13:32.66: [11552]: <-- [12:AT+FCLASS=1\r] > Jan 22 16:13:32.80: [11552]: --> [2:OK] > Jan 22 16:13:32.80: [11552]: DIAL 54640 > Jan 22 16:13:32.80: [11552]: <-- [10:ATDT54640\r] > Jan 22 16:13:44.11: [11552]: --> [7:CONNECT] > Jan 22 16:13:45.59: [11552]: --> [2:OK] > Jan 22 16:13:45.59: [11552]: REMOTE NSF "00 00 25 00 00 00 92 10 4D 02 00 58 00 28 00 A0 80 80 B1 60" > Jan 22 16:13:45.59: [11552]: NSF remote fax equipment: Ricoh > Jan 22 16:13:45.59: [11552]: <-- [9:AT+FRH=3\r] > Jan 22 16:13:45.60: [11552]: --> [7:CONNECT] > Jan 22 16:13:46.02: [11552]: --> [2:OK] > Jan 22 16:13:46.02: [11552]: REMOTE best rate 33600 bit/s > Jan 22 16:13:46.02: [11552]: REMOTE max A3 page width (303 mm) > Jan 22 16:13:46.02: [11552]: REMOTE max unlimited page length > Jan 22 16:13:46.02: [11552]: REMOTE best vres 200 x 200 dpi > Jan 22 16:13:46.02: [11552]: REMOTE format support: MH, MR, MMR, JBIG Jan 22 16:13:46.02: [11552]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 22 16:13:46.02: [11552]: REMOTE best 10 ms/scanline > Jan 22 16:13:46.02: [11552]: USE 14400 bit/s > Jan 22 16:13:46.02: [11552]: USE error correction mode > Jan 22 16:13:46.02: [11552]: SEND file "docq/cover59;f0" > Jan 22 16:13:46.02: [11552]: USE A4 page width (215 mm) > Jan 22 16:13:46.02: [11552]: USE unlimited page length > Jan 22 16:13:46.02: [11552]: USE 3.85 line/mm > Jan 22 16:13:46.02: [11552]: USE 2-D MMR > Jan 22 16:13:46.02: [11552]: USE 0 ms/scanline > Jan 22 16:13:46.02: [11552]: SEND training at v.17 14400 bit/s > Jan 22 16:13:46.02: [11552]: DELAY 70 ms > Jan 22 16:13:46.09: [11552]: <-- [9:AT+FTH=3\r] > Jan 22 16:13:46.28: [11552]: --> [7:CONNECT] > Jan 22 16:13:46.28: [11552]: <-- data [23] > Jan 22 16:13:46.28: [11552]: <-- data [2] > Jan 22 16:13:46.30: [11552]: --> [7:CONNECT] > Jan 22 16:13:46.30: [11552]: <-- data [7] > Jan 22 16:13:46.30: [11552]: <-- data [2] > Jan 22 16:13:48.28: [11552]: --> [2:OK] > Jan 22 16:13:48.28: [11552]: <-- [9:AT+FTS=7\r] > Jan 22 16:13:48.36: [11552]: --> [2:OK] > Jan 22 16:13:48.36: [11552]: <-- [11:AT+FTM=145\r] > Jan 22 16:13:49.84: [11552]: --> [7:CONNECT] > Jan 22 16:13:49.84: [11552]: <-- data [1024] > Jan 22 16:13:49.84: [11552]: <-- data [1024] > Jan 22 16:13:49.84: [11552]: <-- data [652] > Jan 22 16:13:49.84: [11552]: <-- data [2] > Jan 22 16:13:51.37: [11552]: --> [2:OK] > Jan 22 16:13:51.37: [11552]: <-- [9:AT+FRS=1\r] > Jan 22 16:13:51.39: [11552]: --> [2:OK] > Jan 22 16:13:51.39: [11552]: <-- [9:AT+FRH=3\r] > Jan 22 16:13:52.56: [11552]: --> [7:CONNECT] > Jan 22 16:13:53.17: [11552]: --> [2:OK] > Jan 22 16:13:53.17: [11552]: TRAINING succeeded > Jan 22 16:13:53.17: [11552]: SEND begin page > Jan 22 16:13:53.17: [11552]: SEND EOFB > Jan 22 16:13:53.17: [11552]: SEND send frame number 0 > Jan 22 16:13:53.17: [11552]: SEND send frame number 1 > Jan 22 16:13:53.17: [11552]: SEND send frame number 2 > Jan 22 16:13:53.17: [11552]: SEND send frame number 3 > Jan 22 16:13:53.17: [11552]: SEND send frame number 4 > Jan 22 16:13:53.17: [11552]: SEND send frame number 5 > Jan 22 16:13:53.17: [11552]: SEND send frame number 6 > Jan 22 16:13:53.17: [11552]: SEND send frame number 7 > Jan 22 16:13:53.17: [11552]: SEND send frame number 8 > Jan 22 16:13:53.17: [11552]: SEND send frame number 9 > Jan 22 16:13:53.17: [11552]: SEND send frame number 10 > Jan 22 16:13:53.17: [11552]: SEND send frame number 11 > Jan 22 16:13:53.17: [11552]: SEND send frame number 12 > Jan 22 16:13:53.17: [11552]: SEND send frame number 13 > Jan 22 16:13:53.17: [11552]: DELAY 70 ms > Jan 22 16:13:53.24: [11552]: <-- [11:AT+FTM=146\r] > Jan 22 16:13:53.50: [11552]: --> [7:CONNECT] > Jan 22 16:13:53.50: [11552]: <-- data [1034] > Jan 22 16:13:53.50: [11552]: <-- data [1037] > Jan 22 16:13:53.50: [11552]: <-- data [1041] > Jan 22 16:13:53.50: [11552]: <-- data [1031] > Jan 22 16:13:55.49: [11552]: <-- data [49] > Jan 22 16:13:55.49: [11552]: <-- data [2] > Jan 22 16:13:55.83: [11552]: --> [2:OK] > Jan 22 16:13:55.83: [11552]: <-- [9:AT+FTS=7\r] > Jan 22 16:13:55.91: [11552]: --> [2:OK] > Jan 22 16:13:55.91: [11552]: <-- [9:AT+FTH=3\r] > Jan 22 16:13:56.06: [11552]: --> [7:CONNECT] > Jan 22 16:13:56.06: [11552]: <-- data [7] > Jan 22 16:13:56.06: [11552]: <-- data [2] > Jan 22 16:13:57.34: [11552]: --> [2:OK] > Jan 22 16:13:57.34: [11552]: SEND send PPS (partial page signal) Jan 22 16:13:57.34: [11552]: SEND send MPS (more pages, same document) Jan 22 16:13:57.34: [11552]: <-- [9:AT+FRH=3\r] > Jan 22 16:13:57.71: [11552]: --> [10:NO CARRIER] > Jan 22 16:13:57.71: [11552]: MODEM No carrier > Jan 22 16:13:57.71: [11552]: <-- [9:AT+FTH=3\r] > Jan 22 16:13:57.91: [11552]: --> [7:CONNECT] > Jan 22 16:13:57.91: [11552]: <-- data [7] > Jan 22 16:13:57.91: [11552]: <-- data [2] > Jan 22 16:13:59.19: [11552]: --> [2:OK] > Jan 22 16:13:59.19: [11552]: SEND send PPS (partial page signal) Jan 22 16:13:59.19: [11552]: SEND send MPS (more pages, same document) Jan 22 16:13:59.19: [11552]: <-- [9:AT+FRH=3\r] > Jan 22 16:13:59.76: [11552]: --> [10:NO CARRIER] > Jan 22 16:13:59.76: [11552]: MODEM No carrier > Jan 22 16:13:59.76: [11552]: <-- [9:AT+FTH=3\r] > Jan 22 16:13:59.95: [11552]: --> [7:CONNECT] > Jan 22 16:13:59.95: [11552]: <-- data [7] > Jan 22 16:13:59.95: [11552]: <-- data [2] > Jan 22 16:14:01.24: [11552]: --> [2:OK] > Jan 22 16:14:01.24: [11552]: SEND send PPS (partial page signal) Jan 22 16:14:01.24: [11552]: SEND send MPS (more pages, same document) Jan 22 16:14:01.24: [11552]: <-- [9:AT+FRH=3\r] > Jan 22 16:14:01.71: [11552]: --> [10:NO CARRIER] > Jan 22 16:14:01.71: [11552]: MODEM No carrier > Jan 22 16:14:01.71: [11552]: No response to PPS repeated 3 times. Jan 22 16:14:01.71: [11552]: SEND end page > Jan 22 16:14:01.71: [11552]: SEND: Giving up after 3 attempts to send same page "docq/cover59;f0", dirnum 0 > Jan 22 16:14:01.71: [11552]: DELAY 70 ms > Jan 22 16:14:01.79: [11552]: <-- [9:AT+FTH=3\r] > Jan 22 16:14:01.98: [11552]: --> [7:CONNECT] > Jan 22 16:14:01.98: [11552]: <-- data [3] > Jan 22 16:14:01.98: [11552]: <-- data [2] > Jan 22 16:14:03.16: [11552]: --> [2:OK] > Jan 22 16:14:04.16: [11552]: <-- [5:ATH0\r] > Jan 22 16:14:04.39: [11552]: --> [2:OK] > Jan 22 16:14:04.39: [11552]: SESSION END > ------- Unsent job status ------- > Destination: 54640 > JobID: 59 -------------------------------------------------------------------- -------------------------------------------------------------------------- > CS Linux Support Group wrote: >> Hi Lee, >> The modem I'm using is a serial port modem (US Robotics 5686E). >> http://www.usr.com/support/product-template.asp?prod=5686e .I came >> across this post of yours pertaining to USR modems. >> http://ftp.ntua.gr/mirror/hylafax/archive/html/2005-11/msg00182.php >> Does your comment on USR modems apply even now.And moreover the log isnt >> the same everytime.The following is the error log of the fax sent to the >> same receiver. > > Please show me the full log. > > Thanks, > > Lee. > -- Aravindan Dharmalingam CS Linux Support Group ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] No response to PPS repeated 3 times.:
- From: Lee Howard
- Re: [hylafax-users] No response to PPS repeated 3 times.:
- Prev by Date: Re: [hylafax-users] ISO-8859-15 and faxmail
- Next by Date: [hylafax-users] job expiration time
- Previous by thread: Re: [hylafax-users] No response to PPS repeated 3 times.:
- Next by thread: Re: [hylafax-users] No response to PPS repeated 3 times.:
- Index(es):
Project hosted by iFAX Solutions