[hylafax-users] patton 2977 configuration

[ACL <access_you@xxxxxxxxx>]

I have installed patton driver (padm_1_20_1) from their website. Linux is redhat 9.

The driver could be loaded. We could dial and answer.
hylafax: hylafax-4.3.4-1rh9
kernel: 2.4.20-8

It fails to train with modem:

** patton port configuration

[root@localhost root]# dm_admin -b0 -p1 -q
Port Configuration/Information:
        Signalling: pri (NI-2)
        Coding: b8zs
        Framing: esf
        Clock source: loop
        Jitter attenuation: auto
        leased_mask: 0x00000000
        NFAS port: 0
        NFAS ID: 0
        Interface: Short Haul, length:
 0-133
        Equalization gain limit: Low
        LOS:
        Alarm: No Alarm, Loopback: No Loopback
        TX special: 1, Loopback 1, Auto Config 1
        errsec: 0x0, unavailsec: 0x0, burstsec: 0x0
        seversec: 0x0, severfrsec: 0x0, controlslipsec: 0x0
        LOFcount: 0x0, degradmin: 0x0, lineerrsec: 0x0
        linecodevio: 0x319, crcerrcount: 0x0
        Dchannel Mode: 1, Addr Type: 1, Num plan: 1, Subaddr type: 1


hylafax fax log: (remote modem is multitech)
Jan 13 18:37:13.33: [ 4493]: SESSION BEGIN 000153886 110
Jan 13 18:37:13.33: [ 4493]: HylaFAX (tm) Version 4.3.4
Jan 13 18:37:13.33: [ 4493]:
 <-- [4:ATA\r]
Jan 13 18:37:19.28: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:19.28: [ 4493]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyG0_00'
Jan 13 18:37:19.28: [ 4493]: RECV FAX: begin
Jan 13 18:37:19.28: [ 4493]: <-- data [32]
Jan 13 18:37:19.28: [ 4493]: <-- data [2]
Jan 13 18:37:20.63: [ 4493]: --> [1:]
Jan 13 18:37:20.63: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:20.63: [ 4493]: <-- data [23]
Jan 13 18:37:20.63: [ 4493]: <-- data [2]
Jan 13 18:37:21.73: [ 4493]: --> [1:]
Jan 13 18:37:21.73: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:21.73: [ 4493]: <-- data [13]
Jan 13 18:37:21.73: [ 4493]: <-- data [2]
Jan 13 18:37:22.78: [ 4493]: --> [1:]
Jan 13 18:37:22.78: [ 4493]: --> [2:OK]
Jan 13 18:37:22.78: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:23.18: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:23.40: [ 4493]: --> [10:NO CARRIER]
Jan 13 18:37:23.40: [ 4493]: MODEM No
 carrier
Jan 13 18:37:23.40: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:37:23.60: [ 4493]: --> [2:OK]
Jan 13 18:37:23.60: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:37:24.81: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:24.81: [ 4493]: <-- data [3]
Jan 13 18:37:24.81: [ 4493]: <-- data [2]
Jan 13 18:37:25.59: [ 4493]: --> [2:OK]
Jan 13 18:37:25.59: [ 4493]: RECV send CRP (command repeat)
Jan 13 18:37:25.59: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:32.59: [ 4493]: --> [0:]
Jan 13 18:37:32.59: [ 4493]: MODEM <Empty line>
Jan 13 18:37:32.59: [ 4493]: <-- data [1]
Jan 13 18:37:32.65: [ 4493]: --> [2:OK]
Jan 13 18:37:32.65: [ 4493]: DELAY 1500 ms
Jan 13 18:37:34.15: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:37:35.36: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:35.36: [ 4493]: <-- data [32]
Jan 13 18:37:35.36: [ 4493]: <-- data [2]
Jan 13 18:37:36.71: [ 4493]: --> [7:CONNECT]
Jan 13
 18:37:36.71: [ 4493]: <-- data [23]
Jan 13 18:37:36.71: [ 4493]: <-- data [2]
Jan 13 18:37:37.81: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:37.81: [ 4493]: <-- data [13]
Jan 13 18:37:37.81: [ 4493]: <-- data [2]
Jan 13 18:37:38.88: [ 4493]: --> [2:OK]
Jan 13 18:37:38.88: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:39.28: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:40.83: [ 4493]: --> [2:OK]
Jan 13 18:37:40.83: [ 4493]: REMOTE TSI "."
Jan 13 18:37:40.83: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:41.03: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:41.11: [ 4493]: --> [2:OK]
Jan 13 18:37:41.11: [ 4493]: REMOTE wants 12000 bit/s
Jan 13 18:37:41.11: [ 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:37:41.11: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:37:41.11: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:37:41.11: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:37:41.11: [ 4493]: REMOTE wants T.30 Annex
 A, 256-byte ECM
Jan 13 18:37:41.11: [ 4493]: RECV training at v.17 12000 bit/s
Jan 13 18:37:41.11: [ 4493]: <-- [11:AT+FRM=121\r]
Jan 13 18:37:45.61: [ 4493]: --> [0:]
Jan 13 18:37:45.61: [ 4493]: MODEM <Empty line>
Jan 13 18:37:45.61: [ 4493]: <-- data [1]
Jan 13 18:37:45.67: [ 4493]: --> [2:OK]
Jan 13 18:37:45.67: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:37:45.87: [ 4493]: --> [2:OK]
Jan 13 18:37:45.87: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:37:47.08: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:47.08: [ 4493]: <-- data [3]
Jan 13 18:37:47.08: [ 4493]: <-- data [2]
Jan 13 18:37:47.86: [ 4493]: --> [2:OK]
Jan 13 18:37:47.86: [ 4493]: TRAINING failed
Jan 13 18:37:47.86: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:48.24: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:49.81: [ 4493]: --> [2:OK]
Jan 13 18:37:49.81: [ 4493]: REMOTE TSI "."
Jan 13 18:37:49.81: [ 4493]: <-- [9:AT+FRH=3\r]
Jan
 13 18:37:50.01: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:50.09: [ 4493]: --> [2:OK]
Jan 13 18:37:50.09: [ 4493]: REMOTE wants 9600 bit/s
Jan 13 18:37:50.09: [ 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:37:50.09: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:37:50.09: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:37:50.09: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:37:50.09: [ 4493]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 13 18:37:50.09: [ 4493]: RECV training at v.17 9600 bit/s
Jan 13 18:37:50.09: [ 4493]: <-- [10:AT+FRM=97\r]
Jan 13 18:37:54.59: [ 4493]: --> [0:]
Jan 13 18:37:54.59: [ 4493]: MODEM <Empty line>
Jan 13 18:37:54.59: [ 4493]: <-- data [1]
Jan 13 18:37:54.65: [ 4493]: --> [2:OK]
Jan 13 18:37:54.65: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:37:54.86: [ 4493]: --> [2:OK]
Jan 13 18:37:54.86: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:37:56.06: [ 4493]: -->
 [7:CONNECT]
Jan 13 18:37:56.06: [ 4493]: <-- data [3]
Jan 13 18:37:56.06: [ 4493]: <-- data [2]
Jan 13 18:37:56.84: [ 4493]: --> [2:OK]
Jan 13 18:37:56.84: [ 4493]: TRAINING failed
Jan 13 18:37:56.84: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:57.25: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:58.79: [ 4493]: --> [2:OK]
Jan 13 18:37:58.79: [ 4493]: REMOTE TSI "."
Jan 13 18:37:58.79: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:37:59.00: [ 4493]: --> [7:CONNECT]
Jan 13 18:37:59.08: [ 4493]: --> [2:OK]
Jan 13 18:37:59.08: [ 4493]: REMOTE wants 9600 bit/s
Jan 13 18:37:59.08: [ 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:37:59.08: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:37:59.08: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:37:59.08: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:37:59.08: [ 4493]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 13 18:37:59.08: [ 4493]: RECV training at v.29 9600
 bit/s
Jan 13 18:37:59.08: [ 4493]: <-- [10:AT+FRM=96\r]
Jan 13 18:38:03.58: [ 4493]: --> [0:]
Jan 13 18:38:03.58: [ 4493]: MODEM <Empty line>
Jan 13 18:38:03.58: [ 4493]: <-- data [1]
Jan 13 18:38:03.64: [ 4493]: --> [2:OK]
Jan 13 18:38:03.64: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:38:03.84: [ 4493]: --> [2:OK]
Jan 13 18:38:03.84: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:38:05.04: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:05.04: [ 4493]: <-- data [3]
Jan 13 18:38:05.04: [ 4493]: <-- data [2]
Jan 13 18:38:05.83: [ 4493]: --> [2:OK]
Jan 13 18:38:05.83: [ 4493]: TRAINING failed
Jan 13 18:38:05.83: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:06.21: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:07.78: [ 4493]: --> [2:OK]
Jan 13 18:38:07.78: [ 4493]: REMOTE TSI "."
Jan 13 18:38:07.78: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:07.98: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:08.06: [ 4493]:
 --> [2:OK]
Jan 13 18:38:08.06: [ 4493]: REMOTE wants 7200 bit/s
Jan 13 18:38:08.06: [ 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:38:08.06: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:38:08.06: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:38:08.06: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:38:08.06: [ 4493]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 13 18:38:08.06: [ 4493]: RECV training at v.29 7200 bit/s
Jan 13 18:38:08.06: [ 4493]: <-- [10:AT+FRM=72\r]
Jan 13 18:38:12.56: [ 4493]: --> [0:]
Jan 13 18:38:12.56: [ 4493]: MODEM <Empty line>
Jan 13 18:38:12.56: [ 4493]: <-- data [1]
Jan 13 18:38:12.62: [ 4493]: --> [2:OK]
Jan 13 18:38:12.62: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:38:12.82: [ 4493]: --> [2:OK]
Jan 13 18:38:12.82: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:38:14.03: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:14.03: [ 4493]: <-- data [3]
Jan 13 18:38:14.03: [ 4493]:
 <-- data [2]
Jan 13 18:38:14.81: [ 4493]: --> [2:OK]
Jan 13 18:38:14.81: [ 4493]: TRAINING failed
Jan 13 18:38:14.81: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:15.19: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:16.76: [ 4493]: --> [2:OK]
Jan 13 18:38:16.76: [ 4493]: REMOTE TSI "."
Jan 13 18:38:16.76: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:16.96: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:17.02: [ 4493]: --> [2:OK]
Jan 13 18:38:17.02: [ 4493]: REMOTE wants 4800 bit/s
Jan 13 18:38:17.02: [ 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:38:17.02: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:38:17.02: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:38:17.02: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:38:17.02: [ 4493]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 13 18:38:17.02: [ 4493]: RECV training at v.27ter 4800 bit/s
Jan 13 18:38:17.02: [ 4493]: <-- [10:AT+FRM=48\r]
Jan 13 18:38:21.52: [ 4493]:
 --> [0:]
Jan 13 18:38:21.52: [ 4493]: MODEM <Empty line>
Jan 13 18:38:21.52: [ 4493]: <-- data [1]
Jan 13 18:38:21.59: [ 4493]: --> [2:OK]
Jan 13 18:38:21.59: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:38:21.79: [ 4493]: --> [2:OK]
Jan 13 18:38:21.79: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:38:22.99: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:22.99: [ 4493]: <-- data [3]
Jan 13 18:38:22.99: [ 4493]: <-- data [2]
Jan 13 18:38:23.78: [ 4493]: --> [2:OK]
Jan 13 18:38:23.78: [ 4493]: TRAINING failed
Jan 13 18:38:23.78: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:24.16: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:25.73: [ 4493]: --> [2:OK]
Jan 13 18:38:25.73: [ 4493]: REMOTE TSI "."
Jan 13 18:38:25.73: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:25.93: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:26.01: [ 4493]: --> [2:OK]
Jan 13 18:38:26.01: [ 4493]: REMOTE wants 2400 bit/s
Jan 13 18:38:26.01: [
 4493]: REMOTE wants A4 page width (215 mm)
Jan 13 18:38:26.01: [ 4493]: REMOTE wants unlimited page length
Jan 13 18:38:26.01: [ 4493]: REMOTE wants 7.7 line/mm
Jan 13 18:38:26.01: [ 4493]: REMOTE wants 2-D MMR
Jan 13 18:38:26.01: [ 4493]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 13 18:38:26.01: [ 4493]: RECV training at v.27ter fallback mode 2400 bit/s
Jan 13 18:38:26.01: [ 4493]: <-- [10:AT+FRM=24\r]
Jan 13 18:38:30.51: [ 4493]: --> [0:]
Jan 13 18:38:30.51: [ 4493]: MODEM <Empty line>
Jan 13 18:38:30.51: [ 4493]: <-- data [1]
Jan 13 18:38:30.57: [ 4493]: --> [2:OK]
Jan 13 18:38:30.57: [ 4493]: <-- [9:AT+FRS=7\r]
Jan 13 18:38:30.77: [ 4493]: --> [2:OK]
Jan 13 18:38:30.77: [ 4493]: <-- [9:AT+FTH=3\r]
Jan 13 18:38:31.98: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:31.98: [ 4493]: <-- data [3]
Jan 13 18:38:31.98: [ 4493]: <-- data [2]
Jan 13 18:38:32.76: [ 4493]: --> [2:OK]
Jan 13
 18:38:32.76: [ 4493]: TRAINING failed
Jan 13 18:38:32.76: [ 4493]: <-- [9:AT+FRH=3\r]
Jan 13 18:38:32.96: [ 4493]: --> [7:CONNECT]
Jan 13 18:38:34.01: [ 4493]: --> [2:OK]
Jan 13 18:38:34.01: [ 4493]: RECV FAX: RSPREC error/got DCN
Jan 13 18:38:34.01: [ 4493]: RECV FAX: end
Jan 13 18:38:34.01: [ 4493]: SESSION END

hylafax log (remote fax machine is panasonic uf-v40)
Jan 15 18:44:57.35: [10929]: SESSION BEGIN 000153888 110
Jan 15 18:44:57.35: [10929]: HylaFAX (tm) Version 4.3.4
Jan 15 18:44:57.35: [10929]: <-- [4:ATA\r]
Jan 15 18:45:03.29: [10929]: --> [7:CONNECT]
Jan 15 18:45:03.29: [10929]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyG0_00'
Jan 15 18:45:03.29: [10929]: RECV FAX: begin
Jan 15 18:45:03.31: [10929]: <-- data [32]
Jan 15 18:45:03.31: [10929]: <-- data [2]
Jan 15 18:45:04.64: [10929]: --> [1:]
Jan 15 18:45:04.64: [10929]: --> [7:CONNECT]
Jan 15 18:45:04.64: [10929]: <--
 data [23]
Jan 15 18:45:04.64: [10929]: <-- data [2]
Jan 15 18:45:05.74: [10929]: --> [1:]
Jan 15 18:45:05.74: [10929]: --> [7:CONNECT]
Jan 15 18:45:05.74: [10929]: <-- data [13]
Jan 15 18:45:05.74: [10929]: <-- data [2]
Jan 15 18:45:06.79: [10929]: --> [1:]
Jan 15 18:45:06.79: [10929]: --> [2:OK]
Jan 15 18:45:06.79: [10929]: <-- [9:AT+FRH=3\r]
Jan 15 18:45:13.79: [10929]: --> [0:]
Jan 15 18:45:13.79: [10929]: MODEM <Empty line>
Jan 15 18:45:13.79: [10929]: <-- data [1]
Jan 15 18:45:13.84: [10929]: --> [2:OK]
Jan 15 18:45:13.84: [10929]: DELAY 1500 ms
Jan 15 18:45:15.34: [10929]: <-- [9:AT+FTH=3\r]
Jan 15 18:45:16.53: [10929]: --> [7:CONNECT]
Jan 15 18:45:16.53: [10929]: <-- data [32]
Jan 15 18:45:16.53: [10929]: <-- data [2]
Jan 15 18:45:17.88: [10929]: --> [7:CONNECT]
Jan 15 18:45:17.88: [10929]: <-- data [23]
Jan 15 18:45:17.88: [10929]: <-- data
 [2]
Jan 15 18:45:18.99: [10929]: --> [7:CONNECT]
Jan 15 18:45:18.99: [10929]: <-- data [13]
Jan 15 18:45:18.99: [10929]: <-- data [2]
Jan 15 18:45:20.03: [10929]: --> [2:OK]
Jan 15 18:45:20.03: [10929]: <-- [9:AT+FRH=3\r]
Jan 15 18:45:20.55: [10929]: --> [7:CONNECT]
Jan 15 18:45:22.18: [10929]: --> [2:OK]
Jan 15 18:45:22.18: [10929]: REMOTE TSI "+852 12345678"
Jan 15 18:45:22.18: [10929]: <-- [9:AT+FRH=3\r]
Jan 15 18:45:22.36: [10929]: --> [7:CONNECT]
Jan 15 18:45:22.46: [10929]: --> [2:OK]
Jan 15 18:45:22.46: [10929]: REMOTE wants 9600 bit/s
Jan 15 18:45:22.46: [10929]: REMOTE wants A4 page width (215 mm)
Jan 15 18:45:22.46: [10929]: REMOTE wants unlimited page length
Jan 15 18:45:22.46: [10929]: REMOTE wants 3.85 line/mm
Jan 15 18:45:22.46: [10929]: REMOTE wants 2-D MR
Jan 15 18:45:22.46: [10929]: RECV training at v.29 9600 bit/s
Jan 15 18:45:22.46: [10929]: <-- [10:AT+FRM=96\r]
Jan
 15 18:45:26.96: [10929]: --> [0:]
Jan 15 18:45:26.96: [10929]: MODEM <Empty line>
Jan 15 18:45:26.96: [10929]: <-- data [1]
Jan 15 18:45:27.00: [10929]: --> [2:OK]
Jan 15 18:45:27.00: [10929]: <-- [9:AT+FRS=7\r]
Jan 15 18:45:27.19: [10929]: --> [2:OK]
Jan 15 18:45:27.19: [10929]: <-- [9:AT+FTH=3\r]
Jan 15 18:45:28.39: [10929]: --> [7:CONNECT]
Jan 15 18:45:28.39: [10929]: <-- data [3]
Jan 15 18:45:28.39: [10929]: <-- data [2]
Jan 15 18:45:29.17: [10929]: --> [2:OK]
Jan 15 18:45:29.17: [10929]: TRAINING failed
Jan 15 18:45:29.17: [10929]: <-- [9:AT+FRH=3\r]
Jan 15 18:45:35.10: [10929]: --> [10:NO CARRIER]
Jan 15 18:45:35.10: [10929]: MODEM No carrier
Jan 15 18:45:35.10: [10929]: DELAY 1500 ms
Jan 15 18:45:36.60: [10929]: <-- [9:AT+FTH=3\r]
Jan 15 18:45:36.77: [10929]: --> [5:ERROR]
Jan 15 18:45:36.77: [10929]: RECV FAX: RSPREC error/got EOT
Jan 15 18:45:36.78: [10929]:
 RECV FAX: end
Jan 15 18:45:36.78: [10929]: SESSION END


/etc/inittab:
t0:2345:respawn:/usr/sbin/faxgetty ttyG0_00
t1:2345:respawn:/usr/sbin/faxgetty ttyG0_01

etc/config.ttyG0_00
# $Id: digi,v 1.5 2006/04/03 14:57:34 darren Exp $
#
# prototype config for Digi AccelePort RAS
# It uses a K56 chip, but is similar in behavior to Lucents.
#
# Note that because the devices are named as "ttyG0_00" (which on some
# systems indicates a subdirectory, i.e. "ttyG0/00") you must:
# `ln -s /dev/ttyG0_00 /dev/ttyG000`
# for each device and refer to the symlink.  Otherwise various HylaFAX 
# functions will fail.

#
CountryCode:        1
AreaCode:        1
FAXNumber:        0
LongDistancePrefix:    1
InternationalPrefix:    011
DialStringRules:   
 etc/dialrules
ServerTracing:        1
SessionTracing:        11
RecvFileMode:        0600
LogFileMode:        0600
DeviceMode:        0600
RingsBeforeAnswer:    1
SpeakerVolume:        off
GettyArgs:        "-h %l dx_%s"
LocalIdentifier:    0
TagLineFont:        etc/lutRS18.pcf
TagLineFormat:        "From %%l|%c|Page %%P of %%T"
MaxRecvPages:        25
#

ModemType:        Class1        # use this to supply a hint
ModemFlowControl:    rtscts        # seems to work better than xonxoff

# If
 your line supports Caller-ID, you may want to uncomment this...
# ModemResetCmds:    "AT#CID=1"
# CallIDPattern:    "NMBR="
# CallIDPattern:    "NAME="

# The modem does not report +FCERROR, so this helps us simulate it
Class1RMPersistence:    0

Pls kindly advise.

---

使用Yahoo! Mail，2008年繼續賞你無限驚喜，更有機會贏 iPod Touch! 立即參加