Re: [hylafax-users] problem sending fax with iaxmodem

[nik600 <nik600@xxxxxxxxx>]

Here there is the complete log of errors:

Nov 27 18:45:39.43: [12558]: SESSION BEGIN 000001134 398000465xxxxxxx
Nov 27 18:45:39.43: [12558]: HylaFAX (tm) Version 4.4.2
Nov 27 18:45:39.43: [12558]: SEND FAX: JOB 303 DEST 0465xxxxxx COMMID
000001134 DEVICE '/dev/ttyiaxmodem/1' FROM 'nicola <nik600@xxxxxxxxx>'
USER uucp
Nov 27 18:45:39.43: [12558]: STATE CHANGE: RUNNING -> SENDING
Nov 27 18:45:39.43: [12558]: <-- [12:AT+FCLASS=1\r]
Nov 27 18:45:39.43: [12558]: --> [2:OK]
Nov 27 18:45:39.43: [12558]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Nov 27 18:45:39.43: [12558]: DIAL 0465670131
Nov 27 18:45:39.43: [12558]: <-- [15:ATDT0465670131\r]
Nov 27 18:45:54.80: [12558]: --> [7:CONNECT]
Nov 27 18:45:56.06: [12558]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Nov 27 18:45:56.07: [12558]: --> [2:OK]
Nov 27 18:45:56.07: [12558]: REMOTE NSF "AD 00 36 A0 00 00 00 00"
Nov 27 18:45:56.07: [12558]: NSF remote fax equipment: HP
Nov 27 18:45:56.07: [12558]: <-- [9:AT+FRH=3\r]
Nov 27 18:45:56.76: [12558]: --> [7:CONNECT]
Nov 27 18:45:56.77: [12558]: --> HDLC<25:FF C0 02 8C CC 8C 0C EC 6C AC
6C 2C 0C 04 04 04 04 04 04 04 04 04 04 E8 7C>
Nov 27 18:45:56.77: [12558]: --> [2:OK]
Nov 27 18:45:56.77: [12558]: REMOTE CSI "0465670131"
Nov 27 18:45:56.77: [12558]: <-- [9:AT+FRH=3\r]
Nov 27 18:45:57.20: [12558]: --> [7:CONNECT]
Nov 27 18:45:57.20: [12558]: --> HDLC<15:FF C8 01 04 77 1F 23 01 49 01
01 19 00 97 91>
Nov 27 18:45:57.32: [12558]: --> [2:OK]
Nov 27 18:45:57.33: [12558]: REMOTE best rate 33600 bit/s
Nov 27 18:45:57.33: [12558]: REMOTE max A4 page width (215 mm)
Nov 27 18:45:57.33: [12558]: REMOTE max unlimited page length
Nov 27 18:45:57.33: [12558]: REMOTE best vres 300 x 300 dpi
Nov 27 18:45:57.33: [12558]: REMOTE format support: MH, MR, MMR, JPEG Full-Color
Nov 27 18:45:57.33: [12558]: REMOTE supports T.30 Annex A, 256-byte ECM
Nov 27 18:45:57.33: [12558]: REMOTE best 0 ms/scanline
Nov 27 18:45:57.33: [12558]: USE 14400 bit/s
Nov 27 18:45:57.33: [12558]: USE error correction mode
Nov 27 18:45:57.33: [12558]: SEND file "docq/doc355.ps;f0"
Nov 27 18:45:57.33: [12558]: USE A4 page width (215 mm)
Nov 27 18:45:57.33: [12558]: USE unlimited page length
Nov 27 18:45:57.33: [12558]: USE 3.85 line/mm
Nov 27 18:45:57.33: [12558]: USE 2-D MMR
Nov 27 18:45:57.33: [12558]: USE 0 ms/scanline
Nov 27 18:45:57.33: [12558]: SEND training at v.17 14400 bit/s
Nov 27 18:45:57.33: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:45:57.40: [12558]: --> [2:OK]
Nov 27 18:45:57.40: [12558]: <-- [9:AT+FTH=3\r]
Nov 27 18:45:57.42: [12558]: --> [7:CONNECT]
Nov 27 18:45:57.42: [12558]: <-- HDLC<23:FF C0 C2 32 4A CA 04 A6 46 B6
AE D2 04 04 04 04 04 04 04 04 04 04 04>
Nov 27 18:45:57.42: [12558]: <-- data [23]
Nov 27 18:45:57.42: [12558]: <-- data [2]
Nov 27 18:45:58.95: [12558]: --> [7:CONNECT]
Nov 27 18:45:58.95: [12558]: <-- HDLC<7:FF C8 C1 00 44 1F 22>
Nov 27 18:45:58.95: [12558]: <-- data [7]
Nov 27 18:45:58.95: [12558]: <-- data [2]
Nov 27 18:45:59.35: [12558]: --> [2:OK]
Nov 27 18:45:59.35: [12558]: <-- [9:AT+FTS=7\r]
Nov 27 18:45:59.43: [12558]: --> [2:OK]
Nov 27 18:45:59.43: [12558]: MODEM set XON/XOFF/FLUSH: input
interpreted, output disabled
Nov 27 18:45:59.43: [12558]: <-- [11:AT+FTM=145\r]
Nov 27 18:45:59.44: [12558]: --> [7:CONNECT]
Nov 27 18:45:59.44: [12558]: DELAY 400 ms
Nov 27 18:45:59.83: [12558]: <-- data [1024]
Nov 27 18:45:59.83: [12558]: <-- data [1024]
Nov 27 18:45:59.83: [12558]: <-- data [652]
Nov 27 18:45:59.83: [12558]: <-- data [2]
Nov 27 18:46:02.39: [12558]: --> [2:OK]
Nov 27 18:46:02.39: [12558]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Nov 27 18:46:02.39: [12558]: <-- [9:AT+FRH=3\r]
Nov 27 18:46:02.62: [12558]: --> [7:CONNECT]
Nov 27 18:46:03.68: [12558]: --> HDLC<5:FF C8 22 67 DD>
Nov 27 18:46:03.78: [12558]: --> [2:OK]
Nov 27 18:46:03.78: [12558]: SEND training at v.17 12000 bit/s
Nov 27 18:46:03.78: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:46:03.84: [12558]: --> [2:OK]
Nov 27 18:46:03.84: [12558]: <-- [9:AT+FTH=3\r]
Nov 27 18:46:03.85: [12558]: --> [7:CONNECT]
Nov 27 18:46:03.85: [12558]: <-- HDLC<23:FF C0 C2 32 4A CA 04 A6 46 B6
AE D2 04 04 04 04 04 04 04 04 04 04 04>
Nov 27 18:46:03.86: [12558]: <-- data [23]
Nov 27 18:46:03.86: [12558]: <-- data [2]
Nov 27 18:46:11.40: [12558]: --> [0:]
Nov 27 18:46:11.40: [12558]: MODEM <Empty line>
Nov 27 18:46:11.40: [12558]: MODEM TIMEOUT: sending TSI frame
Nov 27 18:46:11.40: [12558]: Error sending T.30 prologue frames
Nov 27 18:46:11.40: [12558]: SEND training at v.29 9600 bit/s
Nov 27 18:46:11.41: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:46:41.40: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:46:41.40: [12558]: MODEM <Timeout>
Nov 27 18:46:41.40: [12558]: Failure to receive silence
(synchronization failure).
Nov 27 18:46:41.40: [12558]: <-- data [1]
Nov 27 18:46:41.60: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:46:41.60: [12558]: MODEM <Timeout>
Nov 27 18:46:41.60: [12558]: Error sending T.30 prologue frames
Nov 27 18:46:41.60: [12558]: SEND training at v.29 7200 bit/s
Nov 27 18:46:41.60: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:47:11.60: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:47:11.60: [12558]: MODEM <Timeout>
Nov 27 18:47:11.60: [12558]: Failure to receive silence
(synchronization failure).
Nov 27 18:47:11.60: [12558]: <-- data [1]
Nov 27 18:47:11.80: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:47:11.80: [12558]: MODEM <Timeout>
Nov 27 18:47:11.80: [12558]: Error sending T.30 prologue frames
Nov 27 18:47:11.80: [12558]: SEND training at v.27ter 4800 bit/s
Nov 27 18:47:11.80: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:47:41.80: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:47:41.80: [12558]: MODEM <Timeout>
Nov 27 18:47:41.80: [12558]: Failure to receive silence
(synchronization failure).
Nov 27 18:47:41.80: [12558]: <-- data [1]
Nov 27 18:47:42.00: [12558]: MODEM TIMEOUT: reading line from modem
Nov 27 18:47:42.00: [12558]: MODEM <Timeout>
Nov 27 18:47:42.00: [12558]: Error sending T.30 prologue frames
Nov 27 18:47:42.00: [12558]: SEND training at v.27ter fallback mode 2400 bit/s
Nov 27 18:47:42.00: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:47:53.06: [12558]: --> [10:NO CARRIER]
Nov 27 18:47:53.06: [12558]: MODEM No carrier
Nov 27 18:47:53.07: [12558]: Failure to receive silence
(synchronization failure).
Nov 27 18:47:53.07: [12558]: Error sending T.30 prologue frames
Nov 27 18:47:53.07: [12558]: TRAINING failed
Nov 27 18:47:53.07: [12558]: SEND: Giving up after 3 attempts to send
same page "docq/doc355.ps;f0", dirnum 0
Nov 27 18:47:53.07: [12558]: <-- [9:AT+FRS=7\r]
Nov 27 18:47:53.07: [12558]: --> [5:ERROR]
Nov 27 18:47:53.07: [12558]: MODEM Command error
Nov 27 18:47:53.07: [12558]: Failure to receive silence
(synchronization failure).
Nov 27 18:47:53.07: [12558]: <-- [9:AT+FTH=3\r]
Nov 27 18:47:53.07: [12558]: --> [5:ERROR]
Nov 27 18:47:53.07: [12558]: MODEM input buffering enabled
Nov 27 18:47:54.07: [12558]: <-- [5:ATH0\r]
Nov 27 18:47:57.27: [12558]: --> [2:OK]
Nov 27 18:47:57.27: [12558]: MODEM set DTR OFF
Nov 27 18:47:57.27: [12558]: MODEM set baud rate: 0 baud (flow control
unchanged)
Nov 27 18:47:57.28: [12558]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 27 18:47:57.28: [12558]: SESSION END

On Nov 27, 2007 6:52 PM, nik600 <nik600@xxxxxxxxx> wrote:
> Hi
>
> i've set up asterisk with hylafax using iaxmodem.
>
> I can correctly receive fax, but if i try to send fax with the
> iaxmodem fax, i get this error:
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*