 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problems with Error "DIS/DTC received 3 times; DCS not recognized"
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Problems with Error "DIS/DTC received 3 times; DCS not recognized"
- From: Roger Meier <roger.meier@xxxxxxxxxxxx>
- Date: Thu, 18 Oct 2007 16:41:28 +0200
Hello Everyone
I see on the offical Handbook, that i shoul'd mail to this Mailing List,
when I have
a Faxing Error like "DCS sent 3 times without response".
I can reproduce this error if i try to send a fax via the faxfrontend,
or with another
programm to sending faxes.
Here is a short Snipped of the Logfile:
-- SNIP --
Your job to XXX failed because:
DIS/DTC received 3 times; DCS not recognized; Giving up after 3 attempts
to send same page
---- Transcript of session follows ----
Oct 18 16:30:54.55: [ 1338]: SESSION BEGIN 000000015 XDESTNUMX
Oct 18 16:30:54.55: [ 1338]: HylaFAX (tm) Version 4.3.3
Oct 18 16:30:54.55: [ 1338]: SEND FAX: JOB 4 DEST XDESTNUMX COMMID
000000015 DEVICE '/dev/ttyS1' FROM 'XX@XX' USER XX
Oct 18 16:30:54.55: [ 1338]: STATE CHANGE: RUNNING -> SENDING
Oct 18 16:30:54.55: [ 1338]: <-- [12:AT+FCLASS=1\r]
Oct 18 16:30:54.57: [ 1338]: --> [2:OK]
Oct 18 16:30:54.57: [ 1338]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Oct 18 16:30:54.57: [ 1338]: DIAL XDESTNUMX
Oct 18 16:30:54.57: [ 1338]: <-- [15:ATDTXDESTNUMX\r]
Oct 18 16:31:05.13: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:06.55: [ 1338]: --> HDLC<23:FF C0 02 8C 2C D4 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 18 16:31:06.55: [ 1338]: --> [2:OK]
Oct 18 16:31:06.55: [ 1338]: REMOTE CSI "+41"
Oct 18 16:31:06.55: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:06.58: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:06.97: [ 1338]: --> HDLC<13:FF C8 01 00 72 1F 21 01 09 01
01 19 00>
Oct 18 16:31:06.98: [ 1338]: --> [2:OK]
Oct 18 16:31:06.98: [ 1338]: REMOTE best rate 9600 bit/s
Oct 18 16:31:06.98: [ 1338]: REMOTE max A4 page width (215 mm)
Oct 18 16:31:06.98: [ 1338]: REMOTE max unlimited page length
Oct 18 16:31:06.98: [ 1338]: REMOTE best vres 7.7 line/mm
Oct 18 16:31:06.98: [ 1338]: REMOTE format support: MH
Oct 18 16:31:06.98: [ 1338]: REMOTE supports T.30 Annex A, 256-byte ECM
Oct 18 16:31:06.98: [ 1338]: REMOTE best 0 ms/scanline
Oct 18 16:31:06.98: [ 1338]: USE 9600 bit/s
Oct 18 16:31:06.98: [ 1338]: USE error correction mode
Oct 18 16:31:06.98: [ 1338]: USE A4 page width (215 mm)
Oct 18 16:31:06.98: [ 1338]: USE unlimited page length
Oct 18 16:31:06.98: [ 1338]: USE 3.85 line/mm
Oct 18 16:31:06.98: [ 1338]: USE 1-D MH
Oct 18 16:31:06.98: [ 1338]: USE 0 ms/scanline
Oct 18 16:31:06.98: [ 1338]: SEND training at v.29 9600 bit/s
Oct 18 16:31:06.98: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:07.08: [ 1338]: --> [2:OK]
Oct 18 16:31:07.08: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:08.11: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:08.11: [ 1338]: <-- HDLC<23:FF C0 C2 76 A6 2E D6 A6 2E 96
16 C6 4E 82 96 36 16 2E A6 EA 04 04 04>
Oct 18 16:31:09.11: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:09.11: [ 1338]: <-- HDLC<7:FF C8 C1 00 60 1F 20>
Oct 18 16:31:09.44: [ 1338]: --> [2:OK]
Oct 18 16:31:09.44: [ 1338]: <-- [9:AT+FTS=7\r]
Oct 18 16:31:09.53: [ 1338]: --> [2:OK]
Oct 18 16:31:09.53: [ 1338]: MODEM set XON/XOFF/FLUSH: input
interpreted, output disabled
Oct 18 16:31:09.53: [ 1338]: <-- [10:AT+FTM=96\r]
Oct 18 16:31:10.14: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:11.63: [ 1338]: --> [2:OK]
Oct 18 16:31:11.63: [ 1338]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Oct 18 16:31:11.63: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:11.90: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:12.51: [ 1338]: --> HDLC<3:FF C8 21>
Oct 18 16:31:12.51: [ 1338]: --> [2:OK]
Oct 18 16:31:12.51: [ 1338]: HDLC frame too short (3 bytes)
Oct 18 16:31:12.51: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:12.61: [ 1338]: --> [2:OK]
Oct 18 16:31:12.61: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:13.64: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:13.64: [ 1338]: <-- HDLC<3:FF C8 D8>
Oct 18 16:31:13.86: [ 1338]: --> [2:OK]
Oct 18 16:31:13.86: [ 1338]: SEND send CRP (command repeat)
Oct 18 16:31:13.86: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:14.21: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:15.63: [ 1338]: --> HDLC<23:FF C0 02 8C 2C D4 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 18 16:31:15.63: [ 1338]: --> [2:OK]
Oct 18 16:31:15.63: [ 1338]: REMOTE CSI "+41"
Oct 18 16:31:15.63: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:15.66: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:16.05: [ 1338]: --> HDLC<13:FF C8 01 00 72 1F 21 01 09 01
01 19 00>
Oct 18 16:31:16.06: [ 1338]: --> [2:OK]
Oct 18 16:31:16.06: [ 1338]: SEND training at v.29 9600 bit/s
Oct 18 16:31:16.06: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:16.15: [ 1338]: --> [2:OK]
Oct 18 16:31:16.15: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:17.18: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:17.18: [ 1338]: <-- HDLC<23:FF C0 C2 76 A6 2E D6 A6 2E 96
16 C6 4E 82 96 36 16 2E A6 EA 04 04 04>
Oct 18 16:31:18.19: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:18.19: [ 1338]: <-- HDLC<7:FF C8 C1 00 60 1F 20>
Oct 18 16:31:18.52: [ 1338]: --> [2:OK]
Oct 18 16:31:18.52: [ 1338]: <-- [9:AT+FTS=7\r]
Oct 18 16:31:18.62: [ 1338]: --> [2:OK]
Oct 18 16:31:18.62: [ 1338]: MODEM set XON/XOFF/FLUSH: input
interpreted, output disabled
Oct 18 16:31:18.62: [ 1338]: <-- [10:AT+FTM=96\r]
Oct 18 16:31:19.22: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:20.71: [ 1338]: --> [2:OK]
Oct 18 16:31:20.71: [ 1338]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Oct 18 16:31:20.71: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:20.98: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:21.59: [ 1338]: --> HDLC<3:FF C8 21>
Oct 18 16:31:21.59: [ 1338]: --> [2:OK]
Oct 18 16:31:21.59: [ 1338]: HDLC frame too short (3 bytes)
Oct 18 16:31:21.59: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:21.69: [ 1338]: --> [2:OK]
Oct 18 16:31:21.69: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:22.72: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:22.72: [ 1338]: <-- HDLC<3:FF C8 D8>
Oct 18 16:31:22.94: [ 1338]: --> [2:OK]
Oct 18 16:31:22.94: [ 1338]: SEND send CRP (command repeat)
Oct 18 16:31:22.94: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:23.28: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:24.70: [ 1338]: --> HDLC<23:FF C0 02 8C 2C D4 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 18 16:31:24.70: [ 1338]: --> [2:OK]
Oct 18 16:31:24.70: [ 1338]: REMOTE CSI "+41"
Oct 18 16:31:24.70: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:24.73: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:25.13: [ 1338]: --> HDLC<13:FF C8 01 00 72 1F 21 01 09 01
01 19 00>
Oct 18 16:31:25.14: [ 1338]: --> [2:OK]
Oct 18 16:31:25.14: [ 1338]: SEND training at v.29 9600 bit/s
Oct 18 16:31:25.14: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:25.23: [ 1338]: --> [2:OK]
Oct 18 16:31:25.23: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:26.26: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:26.26: [ 1338]: <-- HDLC<23:FF C0 C2 76 A6 2E D6 A6 2E 96
16 C6 4E 82 96 36 16 2E A6 EA 04 04 04>
Oct 18 16:31:27.27: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:27.27: [ 1338]: <-- HDLC<7:FF C8 C1 00 60 1F 20>
Oct 18 16:31:27.60: [ 1338]: --> [2:OK]
Oct 18 16:31:27.60: [ 1338]: <-- [9:AT+FTS=7\r]
Oct 18 16:31:27.69: [ 1338]: --> [2:OK]
Oct 18 16:31:27.69: [ 1338]: MODEM set XON/XOFF/FLUSH: input
interpreted, output disabled
Oct 18 16:31:27.69: [ 1338]: <-- [10:AT+FTM=96\r]
Oct 18 16:31:28.30: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:29.79: [ 1338]: --> [2:OK]
Oct 18 16:31:29.79: [ 1338]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Oct 18 16:31:29.79: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:30.05: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:30.66: [ 1338]: --> HDLC<3:FF C8 21>
Oct 18 16:31:30.67: [ 1338]: --> [2:OK]
Oct 18 16:31:30.67: [ 1338]: HDLC frame too short (3 bytes)
Oct 18 16:31:30.67: [ 1338]: <-- [9:AT+FRS=7\r]
Oct 18 16:31:30.77: [ 1338]: --> [2:OK]
Oct 18 16:31:30.77: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:31.80: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:31.80: [ 1338]: <-- HDLC<3:FF C8 D8>
Oct 18 16:31:32.02: [ 1338]: --> [2:OK]
Oct 18 16:31:32.02: [ 1338]: SEND send CRP (command repeat)
Oct 18 16:31:32.02: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:32.36: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:33.78: [ 1338]: --> HDLC<23:FF C0 02 8C 2C D4 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 18 16:31:33.78: [ 1338]: --> [2:OK]
Oct 18 16:31:33.78: [ 1338]: REMOTE CSI "+41"
Oct 18 16:31:33.78: [ 1338]: <-- [9:AT+FRH=3\r]
Oct 18 16:31:33.81: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:34.21: [ 1338]: --> HDLC<13:FF C8 01 00 72 1F 21 01 09 01
01 19 00>
Oct 18 16:31:34.21: [ 1338]: --> [2:OK]
Oct 18 16:31:34.21: [ 1338]: DIS/DTC received 3 times; DCS not recognized
Oct 18 16:31:34.21: [ 1338]: SEND: DIS/DTC received 3 times; DCS not
recognized; Giving up after 3 attempts to send same page
"docq/cover4;00", dirnum 0
Oct 18 16:31:34.21: [ 1338]: <-- [9:AT+FTH=3\r]
Oct 18 16:31:35.25: [ 1338]: --> [7:CONNECT]
Oct 18 16:31:35.25: [ 1338]: <-- HDLC<3:FF C8 DF>
Oct 18 16:31:35.46: [ 1338]: --> [2:OK]
Oct 18 16:31:35.46: [ 1338]: MODEM input buffering enabled
Oct 18 16:31:35.46: [ 1338]: <-- [5:ATH0\r]
Oct 18 16:31:35.60: [ 1338]: --> [2:OK]
Oct 18 16:31:35.60: [ 1338]: MODEM set DTR OFF
Oct 18 16:31:35.60: [ 1338]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Oct 18 16:31:35.60: [ 1338]: SESSION END
-- SNIP --
And here is the config.ttyS1 config (made with addfaxmodem):
-- SNIP --
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 41
AreaCode: 44
FAXNumber: +41.44.XXXXXX
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 0xfff
SessionTracing: 0xfff
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-f -b -s %s %l"
LocalIdentifier: Customer
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Von %%l|%c|Seite %%P von %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait
before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait
before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait
before EOP
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and
trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training
failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
-- SNIP --
The Modem that we use is a a "Zyxel omni 56k". I hope someone can help me.
Greeetings
Roger Meier
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Prev by Date: Re: [hylafax-users] 2nd instance of faxgetty won't start
- Next by Date: [hylafax-users] Received Faxes are Not Lined Up Properly
- Previous by thread: [hylafax-users] Notice Of Winning.
- Next by thread: Re: [hylafax-users] Problems with Error "DIS/DTC received 3 times; DCS not recognized"
- Index(es):
Project hosted by iFAX Solutions