[hylafax-users] HylaFAX on SmartLink modem

["Marino Kekana" <kekanam@xxxxxxxxx>]

Hello

I am using Ubuntu 7.04, HylaFAX 4.3.1-3, SmartLink Soft Modem,
2.9.9e-pre1 on Acer TravelMate 240.

Has anyone managed to setup this modem successfully? In my case, the
computer dials the target, which answers. I can hear the beep and the
wabble sounds. However the fax is not sent. probemodem shows that I
have a Class 1 SmartLink Soft Modem, 2.9.9e-pre1. ATI8, ATI9,
AT+FJUNK=?, AT+FJUNK?, AT+FAA=?, AT+FAA?, AT+FAE=?, AT+FAE?, AT+FTS=?
and AT+FRS=? yields      RESULT = "ERROR"        RESPONSE = "ERROR"

The configuration file has
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
8<---------------------
#
ModemType:		Class1		# use this to supply a hint
#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait before PPM
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait before TCF
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait before EOP
Class1SendMsgDelay	200		# 75ms delay after training
Class1SwitchingCmd:	AT+FRS=7	# silence between HDLC recv and trans
#Class1SwitchingCmd:	"<delay:7>" AT+FRS=7	# silence between HDLC recv and trans
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration
8<----------------------------------------------

HylaFAX log output

Sep 29 16:36:13.54: [ 7583]: <-- [12:AT+FCLASS=1\r]
Sep 29 16:36:13.54: [ 7583]: --> [2:OK]
Sep 29 16:36:13.54: [ 7583]: DIAL XXXXXXXXX,,,,XXXX
Sep 29 16:36:13.54: [ 7583]: <-- [23:ATDTXXXXXXXXXX,,,,XXXX\r]
Sep 29 16:36:55.71: [ 7583]: --> [7:CONNECT]
Sep 29 16:36:56.71: [ 7583]: --> [2:OK]
Sep 29 16:36:56.71: [ 7583]: REMOTE NSF "AD 00 36 A0 00 00 00 00"
Sep 29 16:36:56.71: [ 7583]: NSF remote fax equipment: HP
Sep 29 16:36:56.71: [ 7583]: <-- [9:AT+FRH=3\r]
Sep 29 16:36:56.73: [ 7583]: --> [7:CONNECT]
Sep 29 16:36:57.41: [ 7583]: --> [2:OK]
Sep 29 16:36:57.41: [ 7583]: REMOTE CSI "XXXXXXXXXX"
Sep 29 16:36:57.41: [ 7583]: <-- [9:AT+FRH=3\r]
Sep 29 16:36:57.43: [ 7583]: --> [7:CONNECT]
Sep 29 16:36:57.85: [ 7583]: --> [2:OK]
Sep 29 16:36:57.85: [ 7583]: REMOTE best rate 33600 bit/s
Sep 29 16:36:57.85: [ 7583]: REMOTE max A4 page width (215 mm)
Sep 29 16:36:57.85: [ 7583]: REMOTE max unlimited page length
Sep 29 16:36:57.85: [ 7583]: REMOTE best vres 300 x 300 dpi
Sep 29 16:36:57.85: [ 7583]: REMOTE format support: MH, MR, MMR, JPEG Full-Color
Sep 29 16:36:57.85: [ 7583]: REMOTE supports T.30 Annex A, 256-byte ECM
Sep 29 16:36:57.85: [ 7583]: REMOTE best 0 ms/scanline
Sep 29 16:36:57.85: [ 7583]: USE 14400 bit/s
Sep 29 16:36:57.85: [ 7583]: USE error correction mode
Sep 29 16:36:57.85: [ 7583]: SEND file "docq/doc17.ps;40"
Sep 29 16:36:57.85: [ 7583]: USE A4 page width (215 mm)
Sep 29 16:36:57.85: [ 7583]: USE unlimited page length
Sep 29 16:36:57.85: [ 7583]: USE 3.85 line/mm
Sep 29 16:36:57.85: [ 7583]: USE 2-D MMR
Sep 29 16:36:57.85: [ 7583]: USE 0 ms/scanline
Sep 29 16:36:57.85: [ 7583]: SEND training at v.17 14400 bit/s
Sep 29 16:36:57.85: [ 7583]: DELAY 70 ms
Sep 29 16:36:57.92: [ 7583]: <-- [9:AT+FTH=3\r]
Sep 29 16:36:57.99: [ 7583]: --> [7:CONNECT]
Sep 29 16:36:57.99: [ 7583]: <-- data [23]
Sep 29 16:36:57.99: [ 7583]: <-- data [2]
Sep 29 16:36:59.83: [ 7583]: --> [7:CONNECT]
Sep 29 16:36:59.83: [ 7583]: <-- data [7]
Sep 29 16:36:59.83: [ 7583]: <-- data [2]
Sep 29 16:37:00.25: [ 7583]: --> [2:OK]
Sep 29 16:37:00.25: [ 7583]: <-- [9:AT+FTS=7\r]
Sep 29 16:37:00.31: [ 7583]: --> [2:OK]
Sep 29 16:37:00.31: [ 7583]: <-- [11:AT+FTM=145\r]
Sep 29 16:37:00.41: [ 7583]: --> [7:CONNECT]
Sep 29 16:37:00.41: [ 7583]: <-- data [1024]
Sep 29 16:37:00.41: [ 7583]: <-- data [1024]
Sep 29 16:37:00.41: [ 7583]: <-- data [652]
Sep 29 16:37:00.41: [ 7583]: <-- data [2]
Sep 29 16:37:03.57: [ 7583]: --> [2:OK]
Sep 29 16:37:03.57: [ 7583]: <-- [9:AT+FRH=3\r]
Sep 29 16:37:06.68: [ 7583]: --> [0:]
Sep 29 16:37:06.68: [ 7583]: MODEM <Empty line>
Sep 29 16:37:06.68: [ 7583]: <-- data [1]
Sep 29 16:37:06.88: [ 7583]: MODEM <Timeout>
Sep 29 16:37:06.88: [ 7583]: DELAY 1500 ms
Sep 29 16:37:08.38: [ 7583]: SEND training at v.17 12000 bit/s
Sep 29 16:37:08.38: [ 7583]: DELAY 70 ms
Sep 29 16:37:08.45: [ 7583]: <-- [9:AT+FTH=3\r]
Sep 29 16:37:08.45: [ 7583]: --> [7:CONNECT]
Sep 29 16:37:08.45: [ 7583]: <-- data [23]
Sep 29 16:37:08.45: [ 7583]: <-- data [2]
Sep 29 16:37:08.47: [ 7583]: --> [4:OK]
Sep 29 16:37:08.47: [ 7583]: Error sending T.30 prologue frames
Sep 29 16:37:08.47: [ 7583]: SEND training at v.17 9600 bit/s
Sep 29 16:37:08.47: [ 7583]: DELAY 70 ms
8<--------------------------
Sep 29 16:38:10.44: [ 7583]: SEND training at v.27ter fallback mode 2400 bit/s
8<--------------------------
Sep 29 16:38:20.60: [ 7583]: TRAINING failed
Sep 29 16:38:20.60: [ 7583]: SEND: Failure to train remote modem at
2400 bps or minimum speed; Giving up after 3 attempts to send same
page "docq/doc17.ps;40", dirnum 0
8<----------------------------------------------


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*