Re: [hylafax-users] CallerID in italy

["Andrew Rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>]

Hi,

HylaFAX is just a distraction at this point, so to begin with you should unload it and use a terminal program (Minicom or similar) to try capturing Caller ID with your modem.  You will require a copy of the AT commands manual for your modem.  You should also consult with the modem manufacturer to determine whether they support Caller ID on this model and if they do which type they support (Note that the firmware for many modems will claim to support Caller ID BUT the hardware is often missing from the modem).  You should also ask your telco whether Caller ID is passed to the FXS (analog) interface on the TA and if it is what Caller ID standard it adheres to (you really need to know the specifics here if you don't want to waste a lot of time).

Try using Minicom to issue AT commands to enable Caller ID and see what you receive when you call the modem.  It's useful to connect a Caller ID phone to the same line to ensure that you are receiving Caller ID data.

You should probably read the following to get some idea of how complex Caller ID is and why you will be lucky to get it working with a generic off the shelf modem;

http://www.ainslie.org.uk/callerid.htm

http://www.caller-id-answers.info/

If none of this helps then you should also consider booting windows and using the Ascendis Caller ID application to debug your setup;

http://www.ascendis.com/callerid/callerid.php

Regards

ANDREW RINALDI
Mainpine Limited - Support
USA +1 503 822 9944 | Asia/Europe +44 1225 869439  
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com


-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Disaster
Sent: 17 April 2007 10:06
To: Michele Petrazzo - Unipex srl
Cc: Hylafax Mailling List
Subject: Re: [hylafax-users] CallerID in italy

On Tue, 2007-04-17 at 10:29 +0200, Michele Petrazzo - Unipex srl wrote:
> I don't know which standard are active in Italy, but on a ISDN line all
> the "who is" (translate from Italian "Chi é?", so Caller ID ) service is
> active in all ISDN lines, by default. If the OP has a standard ISDN line
> and a modem that support the CID service, I _think_ that all work.
Hi, I just called Telecom Italia and asked about callerid on my fax
lines:
1) one of them is a "real" analog without "who is" service enabled
2) the other 2 are connected to an isdn BRI (NT1 plus) so the service
should be enable by default

anyway I'm not able to receive the callid on my modem connected to the
isdn. here are the relevant parts of my logs:

Apr 17 12:28:34.36: [30264]: SESSION BEGIN 000047047 +39***
Apr 17 12:28:34.36: [30264]: HylaFAX (tm) Version 5.1.2
Apr 17 12:28:34.36: [30264]: <-- [4:ATA\r]
Apr 17 12:28:46.98: [30264]: --> [9:+F34:12,1]
Apr 17 12:28:46.98: [30264]: V.8 handshaking succeeded, V.34-Fax
(SuperG3) capability enabled.
Apr 17 12:28:46.98: [30264]: Primary channel rate: 28800 bit/s, Control
channel rate: 1200 bit/s.
Apr 17 12:28:46.98: [30264]: --> [7:CONNECT]
Apr 17 12:28:46.98: [30264]: ANSWER: FAX CONNECTION  DEVICE
'/dev/ttyACM1'
Apr 17 12:28:46.98: [30264]: STATE CHANGE: ANSWERING -> RECEIVING
Apr 17 12:28:46.98: [30264]: RECV FAX: begin
Apr 17 12:28:46.98: [30264]: Control channel selected
Apr 17 12:28:46.98: [30264]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86
62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 AC 74 8C 74 4C>
Apr 17 12:28:46.98: [30264]: <-- data [32]
Apr 17 12:28:46.98: [30264]: <-- data [2]
Apr 17 12:28:46.98: [30264]: <-- HDLC<23:FF C0 02 32 4A CA 04 F2 92 32
E2 F2 E4 32 32 82 22 04 04 04 04 04 04>
Apr 17 12:28:46.98: [30264]: <-- data [23]
Apr 17 12:28:46.98: [30264]: <-- data [2]
Apr 17 12:28:46.98: [30264]: <-- HDLC<13:FF C8 01 04 77 5F 23 01 FB C1
01 01 18>
Apr 17 12:28:46.98: [30264]: <-- data [13]
Apr 17 12:28:46.98: [30264]: <-- data [2]
Apr 17 12:28:47.90: [30264]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04 89 69>
Apr 17 12:28:47.90: [30264]: REMOTE TSI ""
Apr 17 12:28:47.97: [30264]: --> HDLC<9:FF C8 C1 00 40 1F 22 8B 1B>
Apr 17 12:28:47.97: [30264]: REMOTE wants 28800 bit/s
Apr 17 12:28:47.97: [30264]: REMOTE wants A4 page width (215 mm)
Apr 17 12:28:47.97: [30264]: REMOTE wants unlimited page length
Apr 17 12:28:47.97: [30264]: REMOTE wants 3.85 line/mm
Apr 17 12:28:47.97: [30264]: REMOTE wants 2-D MMR
Apr 17 12:28:47.97: [30264]: REMOTE wants T.30 Annex A, 256-byte ECM

config:
RingsBeforeAnswer:      2
ModemResetCmds: AT+VCID=1
CallIDPattern:  "NMBR="

What I'm missing?

Andrea


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*