Re: [hylafax-users] Hylafax never answers incoming call. Always Listening to rings.

[borgo2000@xxxxxxxx]

Great it works !!!! 

Andrew, thank you a lot. You have saved me and my madness.

Well I didn't choose to disable the distinctive ring feature of the modem,
but I heve prefered to add the following line to the config.ttyS0

RingFax: "RING A"

It's working fine !!!!

(I need to get every incoming call because I'm behind a PBX and distinctive
ring is not working here).

Bye



	--------- Original Message --------
	Da: andrew.rinaldi@xxxxxxxxxxxx
	To: 
	        Cc: hylafax-users@xxxxxxxxxxx
	Oggetto: RE: [hylafax-users] Hylafax never answers incoming call. Always
Listening to rings.
	Data: 08/01/07 13:15
	
	> 
> 
> 
> Hi Andrea,
> 
> Please keep this in list so that everyone can comment and benefit....
> 
> Does your line and modem support distinctive ring ?  If they do then I
think
> the 'RING A' response is the problem.  Try disabling this feature on the
> modem (look at the modem manual regarding ATS70) and/or read the HylaFAX
> documentation relating to this feature.
> 
> Regards
> 
> ANDREW RINALDI
> Mainpine Limited Support
> USA +1 503 822 9944 | Asia/Europe +44 1225 869439  
> andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
> 
> -----Original Message-----
> From: borgo2000@xxxxxxxx [mailto:borgo2000@xxxxxxxx] 
> Sent: 08 January 2007 12:02
> To: andrew.rinaldi@xxxxxxxxxxxx
> Subject: Re: [hylafax-users] Hylafax never answers incoming call. Always
> Listening to rings.
> 
> Yes using minicom I get
> 
> OK
> 
> RING A
> 
> RING A
> 
> ....
> 
> 	--------- Original Message --------
> 	Da: andrew.rinaldi@xxxxxxxxxxxx
> 	To: hylafax-users@xxxxxxxxxxx <hylafax-users@xxxxxxxxxxx>
> 	Oggetto: Re: [hylafax-users] Hylafax never answers incoming call.
> Always Listening to rings.
> 	Data: 08/01/07 12:12
> 	
> 	> 
> > 
> > 
> > Hi Andrea,
> > 
> > Do you see 'ring' if you use Minicom ?
> > 
> > Regards
> > 
> > ANDREW RINALDI
> > Mainpine Limited Support
> > USA +1 503 822 9944 | Asia/Europe +44 1225 869439 
> > andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
> > 
> > -----Original Message-----
> > From: hylafax-users-bounce@xxxxxxxxxxx 
> > [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of 
> > borgo2000@xxxxxxxx
> > Sent: 08 January 2007 10:44
> > To: hylafax-users@xxxxxxxxxxx
> > Subject: [hylafax-users] Hylafax never answers incoming call. Always 
> > Listening to rings.
> > 
> > Hi to everybody
> > I have spent the last two days on the following problem without any
> success.
> > My Hylafax nevere answer to incoming call. It's always listening to 
> > rings but never answer.
> > 
> > 
> > When my modem rings.....
> > 
> > #faxstat
> > 
> > Listening to rings from modem
> > 
> > but hylafax does't answer
> > 
> > The syslog trace is:
> > 
> > 2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: DELAY 
> > 2600
> ms 
> > 
> > 2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM 
> > set
> DTR
> > ON
> > 2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: DELAY 75 
> > ms
> > 2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM 
> > set
> DTR
> > OFF
> > 2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM 
> > set
> DTR
> > OFF
> > 2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: --> 
> > [2:OK]
> > 2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: <--
> [5:ATH0r]
> >  
> > 2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM
> TIMEOUT:
> > reading line from modem
> > 2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: --> 
> > [6:RING
> A]
> >  
> > 2007-01-08 11:37:18 Local4.Info 192.168.0.107 FaxGetty[3017]: --> 
> > [6:RING
> A]
> >  
> > 2007-01-08 11:37:18 Local4.Info 192.168.0.107 FaxGetty[3017]: STATE
> CHANGE:
> > RUNNING -> LISTENING
> > 
> > If I use the faxanswer command everything is OK, and I get my fax. 
> > But I'd like to use the auto-answer with faxgetty.
> > 
> > 
> > Some notes about my config:
> > 
> > 1) I use CentOs 4.4 with USR 56k Professional Message modem
> > 
> > 2) After faxsetup I get two warnings !!! 
> > 
> > Warning: /bin/vgetty does not exist or is not an executable program!
> > Warning: /bin/egetty does not exist or is not an executable program!
> > 
> > 3) In  /etc/inittab I have:
> > 
> > mo:2345:respawn:/usr/sbin/faxgetty ttyS0
> > 
> > 4) My config.ttyS0 is:
> > 
> > # Configuration for using the Class 1 command interface with # a USR
> Courier
> > or Sportster modem and XON/XOFF flow control. 
> > #
> > #
> > LogFacility:            local4
> > CountryCode:            39
> > AreaCode:               0721
> > FAXNumber:              0721.0000
> > LongDistancePrefix:     0
> > InternationalPrefix:    00
> > DialStringRules:        etc/dialrules.europe
> > #ServerTracing:         1
> > ServerTracing:          0xfff
> > SessionTracing:         11
> > RecvFileMode:           0600
> > LogFileMode:            0600
> > DeviceMode:             0600
> > RingsBeforeAnswer:      1
> > SpeakerVolume:          medium
> > GettyArgs:              "-h %l dx_%s"
> > #GettyArgs:             "-t 20 -h %l F%s"
> > LocalIdentifier:        FaxServer
> > TagLineFont:            etc/lutRS18.pcf
> > TagLineFormat:          "From %%l|%c|Page %%P of %%T"
> > MaxRecvPages:           25
> > #
> > #
> > # Modem-related stuff: should reflect modem command interface # and
> hardware
> > connection/cabling (e.g. flow control).
> > #
> > ModemType:              Class1          # use class 1 interface
> > ModemRate:              19200           # rate for DCE-DTE communication
> > #ModemRate:             57600
> > ModemFlowControl:       xonxoff         # software flow control
> > #
> > ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
> > ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
> (or
> > not)
> > ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow
control
> > ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
> > control
> > ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
> > control
> > ModemResultCodesCmd:    ATQ0X4          # enable result codes
> > #
> > ModemMfrQueryCmd:       !USR
> > ModemModelQueryCmd:     ATI3
> > ModemRevQueryCmd:       ATI7            # XXX returns a multi-line
result
> > #
> > # When AT+FCLASS=1 is issued the modem automatically switches # to
> software
> > flow control; these parameters let the fax software # reset flow 
> > control
> as
> > needed after entering Class 1.
> > #
> > Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow
control
> > Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
> > control
> > Class1SFLOCmd:          ""              # modem does this automatically
> > #
> > # This should resolve "DIS/DTC received 3 times" errors:
> > #
> > Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for
> > response
> > #
> > # The remainder of this configuration is included so that the # modem 
> > "idles" in Class 0 while not sending or receiving facsimile.
> > #
> > ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
> > ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
> > #
> > # When using AT+FRS=n we see USR modems reset themselves in the middle 
> > of sessions # this is not good.  So, we seem to work-around that 
> > problem by
> not
> > using the # command.  Unfortunately, this isn't an ideal thing.
> > #
> > Class1SwitchingCmd:     "<delay727>"
> > 
> > 
> > 
> > 
> > Regards and greetings from Italy
> > 
> > Andrea
> >  --
> >  Email.it, the professional e-mail, gratis per te: 
> > http://www.email.it/f
> >  
> >  Sponsor:
> >  Ariatel Vocepiù Ricaricabile: nessun canone, nessun costo mensile, 
> > paghi solo le telefonate e a solo 1,15 cent/min per tutti i numeri 
> > fissi
> d?Italia!
> >  Clicca qui: 
> > http://adv.email.it/cgi-bin/foclick.cgi?mid=5833&d=20070108
> > 
> > 
> > 
> > ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> >   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
> >   *To learn about commercial HylaFAX(tm) support, mail 
> > sales@xxxxxxxxx*
> > 
> > 
> > 
> > 
> > ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> >   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
> >   *To learn about commercial HylaFAX(tm) support, mail 
> > sales@xxxxxxxxx*
> > 
> > 
> > 
> >  
>  --
>  Email.it, the professional e-mail, gratis per te: http://www.email.it/f
>  
>  Sponsor:
>  Stupisci i tuoi Amici con le Fantastiche Idee Regalo D-Mail !
>  Clicca qui: http://adv.email.it/cgi-bin/foclick.cgi?mid=5889&d=20070108
> 
> 
> 
> 
> 
> 
>  
 --
 Email.it, the professional e-mail, gratis per te: http://www.email.it/f
 
 Sponsor:
 La domanda è: come e cosa vuoi comunicare online...la risposta te la diamo
noi....icecube communication, realizza ogni tua esigenza, contattaci
 Clicca qui: http://adv.email.it/cgi-bin/foclick.cgi?mid=5874&d=20070108



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*