[hylafax-users] Hylafax doesn`t work as I suppose to :(

["Thorvald Hallvardsson" <thorvald.hallvardsson@xxxxxxxxx>]

Hello.
I`m new on this mailing list, so please be patient :).

I tried to start my hylafax server but it didn`t work :(. I work on Gentoo @ 2.6.18. I have got Fritz AVM Card installed (ISDN), system see this card. I have installed capi4hylafax, capi and fritz drivers into a kernel, and there are some problems.

1) During a loading fritz card module everything is OK, but in logfile i see:

fcpci: AVM FRITZ!Card PCI found: port 0xc000, irq 10
fcpci: Loading...
fcpci: Driver 'fcpci' attached to fcpci-stack. (152)
fcpci: Stack version 3.11-07
kcapi: Controller 1: fcpci-c000-10 attached
kcapi: card 1 "fcpci-c000-10" ready.
fcpci: Loaded.
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
kobject_add failed for fcpci with -EEXIST, don't try to register things with the same name in the same directory.
 [<c0103acd>] show_trace_log_lvl+0x5b/0x16d
 [<c0104184>] show_trace+0xf/0x11
 [<c010420e>] dump_stack+0x15/0x17
 [<c01dad9e>] kobject_add+0x14c/0x175
 [<c01dae9c>] kobject_register+0x19/0x30
 [<c023e432>] bus_add_driver+0x51/0x104
 [<c01e2cf7>] __pci_register_driver+0x34/0x4e
 [<c012c221>] sys_init_module+0x135b/0x14b0
 [<c0102aed>] sysenter_past_esp+0x56/0x79
DWARF2 unwinder stuck at sysenter_past_esp+0x56/0x79
I don`t know what does it mean. I tried to recompile fritz driver, changed kernel... always is the same result :(.

 

2) Why do I think my hylafax doesn`t work ? So... there are many problems...

First of all when I try to call from any phone to my server, after choosing a number I have got "busy" signal. Something is dropping the connection :(. Inside the logfile is written:

Device "faxCAPI" uses 2 receive thread(s) with the following config:
Nov 13 17:40:14.84: [ 4263]: c2faxrecv - INFO: Controller=1 : IncomingMSNs=18
Nov 13 17:40:14.84: [ 4263]: c2faxrecv - INFO:
Started in G3 mode and waiting on incoming calls.
Nov 14 09:27:03.56: [ 4263]: c2faxrecv - INFO: Incoming speech call on controller 1 from 22.
Nov 14 09:27:07.82: [ 4263]: c2faxrecv - INFO: Connection is droped with reason 0x3303 (Protocol error layer 3).
 

I have no "fax" signal in my phone... almost at the beggining something drop a call. I read somewhere that reason 0x3303 means that modem can`t open channel B. But... so what ? Is it damaged ?

 

3) When I try to send fax from hylafax server to themself I got no result... just do nothing (logfile is emtpy). When I try to send fax to any other device I have got:

Nov 14 11:46:35.17: [ 5257]: CapiFaxSend - INFO: Try to connect to fax number 22 in G3 mode on controller 1.
Nov 14 11:46:35.17: [ 5257]: CapiFaxSend - INFO: Dial and starting transfer of G3-File /mnt/local/1.tiff with fine resolution.
Nov 14 11:46:35.61: [ 5257]: CapiFaxSend - INFO: Connection dropped with Reason 0x3490 (Normal call clearing).
 

Please help me to start my hylafax server.

Thank you very much for any help.

Best regards,

Thorvald