Re: [hylafax-users] martian & Hylafax

["andrew rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>]

Hi Bernd,

As a first step you probably want to upgrade to the latest HylaFAX or
HylaFAX+ version and then report back.  A lot of development has taken place
in Class 1 since 4.2.5

Regards

ANDREW RINALDI
Mainpine Limited Support
USA +1 503 822 9944 | Asia/Europe +44 1225 869439  
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Bernd Stuht
Sent: 28 July 2006 10:30
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] martian & Hylafax

Hello,

after sucessfully compiling and installing the martian driver on my Suse
10.1 and also sucessfull testings with the Internetconnections, i am still
working on get it working with Hylafax.

I have the Error : Stop and Wait failure in the Log from Hylafax, the
Connection to the other Fax starts, the two Faxes start to communicate, but
after first transmissions the Connection stops with that Error.

It seems that it is possible that the LT-Modem or the (martian) Driver does
not support the
AT+FTS=7 ( and =9 ) command ?
I read about the Solution to override this Syntax of Hylafax, but this also
does not work ( other error ).

Attached my config.ttySM0:
Attached Nr. 2: an typical error Log from my Hylafax:

Following - a Text found in the net from an other User who had the same
Problem with an other Modem, but his Solution does not work with my Setup.
( This contains first his Hylafaxlog )


 [...]
 Feb 16 15:20:06.14: [ 528]: SEND file "docq/doc29.ps;00"
 Feb 16 15:20:06.14: [ 528]: USE A4 page width (215 mm)  Feb 16 15:20:06.14:
[ 528]: USE A4 page length (297 mm)  Feb 16 15:20:06.15: [ 528]: USE 3.85
line/mm  Feb 16 15:20:06.15: [ 528]: USE 1-D MH  Feb 16 15:20:06.15: [ 528]:
SEND training at v.29 9600 bit/s  Feb 16 15:20:06.15: [ 528]: <--
[9:AT+FTH=3\r]  Feb 16 15:20:06.29: [ 528]: --> [7:CONNECT]  Feb 16
15:20:06.29: [ 528]: <-- data [23]  Feb 16 15:20:06.29: [ 528]: <-- data [2]
Feb 16 15:20:08.03: [ 528]: --> [7:CONNECT]  Feb 16 15:20:08.03: [ 528]: <--
data [6]  Feb 16 15:20:08.03: [ 528]: <-- data [2]  Feb 16 15:20:08.73: [
528]: --> [2:OK]  Feb 16 15:20:08.73: [ 528]: <-- [9:AT+FTS=7\r]  Feb 16
15:20:08.99: [ 528]: --> [5:ERROR]  Feb 16 15:20:08.99: [ 528]: MODEM
Command error  Feb 16 15:20:08.99: [ 528]: Stop and wait failure (modem on
hook)  Feb 16 15:20:08.99: [ 528]: The destination appears to have trouble
with V.34-Fax.
 [...]
 
 
Interestingly, the /usr/local/sbin/probemodem script had previously detected
that the AT+FTS command could not be digested by my modem. You can run that
script at any time to find out what AT capabilities your modem has.
 
 My modem is configured by file /var/spool/hylafax/etc/config.cua_b. I added
the following lines to stop HylaFAX attempting to use AT+FTS commands:
 
 

Class1PPMWaitCmd:       "<delay\0727>"  # \072 == : to avoid awk problem
Class1TCFWaitCmd:       "<delay\0727>"
Class1EOPWaitCmd:       "<delay\0729>"
Class1SwitchingCmd:     "<delay\0727>"  # assumption: +FRS not supported

 
Probably, the Class1ResponseWaitCmd attribute can be supplied with such a
value. In my current setup, I still see AT+FRS commands and corresponding
errors, but only during the training phase. Apart from this, everything
works fine.
 

***** end of I-Net File

Any Idea ?


Bernd




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*