Re: [hylafax-users] Failed to properly d

[bill.allison@xxxxxxxxx]

I use them very successfully but would also recommend don't buy but if   
you happen to already have one by all means give it a go. Be aware that   
you *must* apply latest firmware upgrades to avoid problems.

Regards
Bill A
   


 -----Original Message-----
From: andrew.rinaldi@xxxxxxxxxxxx
Sent: 17 July 2006 13:29
To: info@xxxxxxx; hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Failed to properly d


   

 --------------------------------------------------------------------------  
 --
Hi Danilo,

I think that most users and developers would recommend that you avoid USR
products with HylaFAX.

Regards

ANDREW RINALDI
Mainpine Ltd. Support
USA +1 718 701 2422 | Asia/Europe +44 1225 436137
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

 -----Original Message-----
From: SCIN - Danilo Bottino [mailto:info@xxxxxxx]
Sent: 17 July 2006 13:23
To: andrew.rinaldi@xxxxxxxxxxxx; hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Failed to properly detect high-speed data
carrier

Hi Andrew,

thanks for your quick reply. About point 1 I'll sure give it a try.. this   
is
my very first setup of a faxserver on linux and I lack experience. About
point 2, I guess it would be easier to buy a brand new modem.. I wonder   
if a
us robotics would work as intendend.

 ----- Original Message -----
From: "andrew rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>
To: "'SCIN - Danilo Bottino'" <info@xxxxxxx>; <hylafax-users@xxxxxxxxxxx>
Sent: Monday, July 17, 2006 2:08 PM
Subject: Re: [hylafax-users] Failed to properly detect high-speed data
carrier


> Hi Danilo,
>
> We have seen a lot of problems with the 'stock' Agere OCM (and OCF)
> firmware.  Here are my suggestions for you to try;
>
> (1) Upgrade to 4.3.0
>
> (2) Ask for a modem firmware upgrade (Note: by default the OCM/OCF
> chipsets do not require external flash memory and a full firmware
> upgrade is therefore impossible... however, if you are VERY lucky the
> board will have a flash chip fitted).
>
> Regards
>
> ANDREW RINALDI
> Mainpine Ltd. Support
> USA +1 718 701 2422 | Asia/Europe +44 1225 436137
> andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
>
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of SCIN - Danilo
> Bottino
> Sent: 17 July 2006 12:56
> To: hylafax-users@xxxxxxxxxxx
> Subject: [hylafax-users] Failed to properly detect high-speed data
> carrier
>
> Hi all,
>
> I did a search but I can't find a solution to this problem. I run
> hylafax
> 4.2.1 on a Debian Sarge box with an external Agere 56k modem.
> Sometimes I receive the infamous 'high-speed data carrier' error, is
> there anything I can do?
>
> The modem is:
>
> MODEM AGERE OCM V.92 VER2.7A (JUN 14 2004) VOICE MERCURY DP2SH MODE-II
> SERIAL Agere OCM V.92 Ver2.7a
>
> And here's the session log:
>
> Jul 17 12:40:56.84: [ 8345]: SESSION BEGIN 000000164 3842448 Jul 17
> 12:40:56.84: [ 8345]: HylaFAX (tm) Version 4.2.1 Jul 17 12:40:56.84: [
> 8345]: <-- [4:ATA\r] Jul 17 12:41:05.63: [ 8345]: --> [7:CONNECT] Jul
> 17
> 12:41:05.63: [ 8345]: ANSWER: FAX CONNECTION  DEVICE '/dev/modem'
> Jul 17 12:41:05.63: [ 8345]: RECV FAX: begin Jul 17 12:41:05.65: [   
8345]:
> --> [7:CONNECT] Jul 17 12:41:05.68: [ 8345]: --> [7:CONNECT] Jul 17
> 12:41:07.81: [ 8345]: --> [2:OK] Jul 17 12:41:07.81: [ 8345]: <--
> [9:AT+FRH=3\r] Jul 17 12:41:07.99: [ 8345]: --> [7:CONNECT] Jul 17
> 12:41:09.73: [ 8345]: --> [2:OK] Jul 17 12:41:09.73: [ 8345]: REMOTE
> TSI "CARREFOUR"
> Jul 17 12:41:09.73: [ 8345]: <-- [9:AT+FRH=3\r] Jul 17 12:41:09.74: [
> 8345]:
> --> [7:CONNECT] Jul 17 12:41:10.03: [ 8345]: --> [2:OK] Jul 17
> 12:41:10.03:
> [ 8345]: REMOTE wants 14400 bit/s Jul 17 12:41:10.03: [ 8345]: REMOTE
> wants
> A4 page width (215 mm) Jul 17 12:41:10.03: [ 8345]: REMOTE wants
> unlimited page length Jul 17 12:41:10.03: [ 8345]: REMOTE wants 7.7
> line/mm Jul 17
> 12:41:10.03: [ 8345]: REMOTE wants 1-D MH Jul 17 12:41:10.03: [ 8345]:
> REMOTE wants T.30 Annex A, 256-byte ECM Jul 17 12:41:10.03: [ 8345]:
> RECV training at v.17 14400 bit/s Jul 17 12:41:10.03: [ 8345]: <--
> [11:AT+FRM=145\r] Jul 17 12:41:11.81: [ 8345]: --> [7:CONNECT] Jul 17
> 12:41:13.32: [ 8345]: RECV: TCF 2720 bytes, 0% non-zero, 2699 zero-run
> Jul
> 17 12:41:13.33: [ 8345]: --> [10:NO CARRIER] Jul 17 12:41:13.33: [   
8345]:
> DELAY 75 ms Jul 17 12:41:13.41: [ 8345]: TRAINING succeeded Jul 17
> 12:41:13.41: [ 8345]: <-- [9:AT+FTH=3\r] Jul 17 12:41:14.27: [ 8345]:
> --> [7:CONNECT] Jul 17 12:41:14.59: [ 8345]: --> [2:OK] Jul 17
> 12:41:14.59: [
> 8345]: <-- [11:AT+FRM=146\r] Jul 17 12:41:15.68: [ 8345]: -->
> [7:CONNECT] Jul 17 12:41:16.03: [ 8345]: RECV received frame number 0   
...
> [cut]
> ...
> Jul 17 12:41:45.24: [ 8345]: RECV received frame number 195 Jul 17
> 12:41:45.31: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.45: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.45: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.52: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.59: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.59: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.59: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.59: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.66: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.66: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:45.66: [ 8345]: HDLC frame too short (4 bytes) Jul 17
> 12:41:45.80: [ 8345]: HDLC frame not byte-oriented.  Trailing byte:
> 0xe0
> Jul 17 12:41:45.87: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf8
> Jul 17 12:41:45.94: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.01: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.08: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.08: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xe0
> Jul 17 12:41:46.08: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf8
> Jul 17 12:41:46.15: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf0
> Jul 17 12:41:46.22: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf0
> Jul 17 12:41:46.29: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.29: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:46.30: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0x80
> Jul 17 12:41:46.37: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:46.44: [ 8345]: HDLC frame with bad address field 0xc2
> Jul 17
> 12:41:46.44: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.58: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf0
> Jul 17 12:41:46.65: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.72: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:46.79: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.79: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:46.79: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf0
> Jul 17 12:41:46.79: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf8
> Jul 17 12:41:46.93: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:46.93: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:47.00: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.00: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:47.07: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.14: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.21: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.21: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.28: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.36: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.43: [ 8345]: HDLC frame with bad address field 0xb7
> Jul 17
> 12:41:47.43: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.64: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.71: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.78: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.78: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.78: [ 8345]: HDLC frame with bad address field 0x84
> Jul 17
> 12:41:47.85: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:47.85: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:47.99: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.06: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.13: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.13: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.13: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0x80
> Jul 17 12:41:48.27: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0x80
> Jul 17 12:41:48.27: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.34: [ 8345]: HDLC frame with bad address field 0x8e
> Jul 17
> 12:41:48.41: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.42: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.42: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:48.48: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:48.56: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.63: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xe0
> Jul 17 12:41:48.70: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xe0
> Jul 17 12:41:48.77: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:48.84: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:

> 0
> Jul 17 12:41:48.84: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:48.91: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xfc
> Jul 17 12:41:48.91: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:48.98: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf8
> Jul 17 12:41:49.05: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:49.12: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xf0
> Jul 17 12:41:49.12: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:49.19: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:49.26: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.33: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.40: [ 8345]: HDLC frame with bad address field 0x9d
> Jul 17
> 12:41:49.47: [ 8345]: HDLC frame not byte-oriented.  Trailing byte: 0
> Jul
> 17
> 12:41:49.47: [ 8345]: HDLC frame not byte-oriented.  Trailing byte:
> 0x80
> Jul 17 12:41:49.54: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.55: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.61: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.61: [ 8345]: HDLC frame not byte-oriented.  Trailing   
byte:
> 0xc0
> Jul 17 12:41:49.62: [ 8345]: Bad HDLC terminating flag received.
> Jul 17 12:41:49.62: [ 8345]: RECV assumed RCP frame with block end Jul
> 17
> 12:41:49.72: [ 8345]: --> [10:NO CARRIER] Jul 17 12:41:49.72: [ 8345]:
> <-- [9:AT+FRH=3\r] Jul 17 12:41:50.02: [ 8345]: --> [7:CONNECT] Jul 17
> 12:41:50.87: [ 8345]: --> [10:NO CARRIER] Jul 17 12:41:50.87: [ 8345]:
> MODEM
> No carrier Jul 17 12:41:50.87: [ 8345]: <-- [9:AT+FRH=3\r] Jul 17
> 12:41:51.16: [ 8345]: --> [7:CONNECT] Jul 17 12:41:52.80: [ 8345]: -->
> [2:OK] Jul 17 12:41:52.80: [ 8345]: RECV recv PPS (partial page
> signal) Jul
> 17 12:41:52.80: [ 8345]: RECV recv MPS (more pages, same document) Jul
> 17
> 12:41:52.80: [ 8345]: RECV received 238 frames of block 1 of page 1
> Jul 17
> 12:41:52.80: [ 8345]: <-- [9:AT+FRS=7\r] Jul 17 12:41:53.04: [ 8345]:
> --> [2:OK] Jul 17 12:41:53.04: [ 8345]: <-- [9:AT+FTH=3\r] Jul 17
12:41:53.90:
> [
> 8345]: --> [7:CONNECT] Jul 17 12:41:55.14: [ 8345]: --> [2:OK] Jul 17
> 12:41:55.14: [ 8345]: RECV send PPR (partial page request) Jul 17
> 12:41:55.14: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17 12:41:55.92: [
> 8345]: -->
> [8:+FCERROR] Jul 17 12:41:55.92: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17
> 12:42:02.62: [ 8345]: --> [8:+FCERROR] Jul 17 12:42:02.62: [ 8345]:
> <-- [11:AT+FRM=146\r] Jul 17 12:42:03.40: [ 8345]: --> [8:+FCERROR]
> Jul 17
> 12:42:03.40: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17 12:42:07.07: [
> 8345]: -->
> [8:+FCERROR] Jul 17 12:42:07.07: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17
> 12:42:07.85: [ 8345]: --> [8:+FCERROR] Jul 17 12:42:07.85: [ 8345]:
> <-- [11:AT+FRM=146\r] Jul 17 12:42:11.45: [ 8345]: --> [8:+FCERROR]
> Jul 17
> 12:42:11.45: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17 12:42:12.23: [
> 8345]: -->
> [8:+FCERROR] Jul 17 12:42:12.23: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17
> 12:42:15.83: [ 8345]: --> [8:+FCERROR] Jul 17 12:42:15.83: [ 8345]:
> <-- [11:AT+FRM=146\r] Jul 17 12:42:16.61: [ 8345]: --> [8:+FCERROR]
> Jul 17
> 12:42:16.61: [ 8345]: <-- [11:AT+FRM=146\r] Jul 17 12:42:23.61: [   
8345]:
> RECV keeping unconfirmed page Jul 17 12:42:23.75: [ 8345]: RECV: 60928
> bytes of data, 1981 total lines Jul 17 12:42:23.86: [ 8345]: -->
> [2:] Jul 17
> 12:42:23.86: [ 8345]: --> [2:OK] Jul 17 12:42:23.86: [ 8345]: <--
> [9:AT+FRS=7\r] Jul 17 12:42:24.08: [ 8345]: --> [2:OK] Jul 17   
12:42:24.09:
> [
> 8345]: RECV FAX (000000164): from CARREFOUR, page 1 in 1:11, INF, 7.7
> line/mm, 1-D MH, 14400 bit/s Jul 17 12:42:24.09: [ 8345]: RECV FAX
> (000000164): recvq/fax000000089.tif from CARREFOUR, route to
> <unspecified>,
> 1 pages in 1:19 Jul 17 12:42:24.09: [ 8345]: RECV FAX: Failed to
> properly detect high-speed data carrier.
> Jul 17 12:42:24.09: [ 8345]: <-- [9:AT+FTH=3\r] Jul 17 12:42:24.95: [
> 8345]:
> --> [7:CONNECT] Jul 17 12:42:25.27: [ 8345]: --> [2:OK] Jul 17
> 12:42:25.27:
> [ 8345]: RECV FAX (000000164): session with CARREFOUR terminated
> abnormally:
> Failed to properly detect high-speed data carrier.
> Jul 17 12:42:25.27: [ 8345]: RECV FAX: bin/faxrcvd
> "recvq/fax000000089.tif"
> "modem" "000000164" "Failed to properly detect high-speed data   
carrier."
> ""
> ""
> Jul 17 12:42:25.28: [ 8345]: RECV FAX: end Jul 17 12:42:25.28: [ 8345]:
> SESSION END
>
> Any help would be greatly appreciated.
>
> _________________________________
> Danilo Bottino - SCIN Servizi Informatici Tel. 011/9242690 Cel.
> 333/2290918
> Fax 011/9242922 info@xxxxxxx - www.scin.it
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________  To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null  *To learn about commercial HylaFAX(tm) support, mail
> sales@xxxxxxxxx*
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________  To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null  *To learn about commercial HylaFAX(tm) support, mail
> sales@xxxxxxxxx*
>
>




____________________ HylaFAX(tm) Users Mailing List   
_______________________
  To subscribe/unsubscribe, click   
http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <   
/dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*