 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] Hylafax terminates while receiving
- To: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
- Subject: Re: [hylafax-users] Hylafax terminates while receiving
- From: Mufit Eribol <hme@xxxxxxxxxxxx>
- Cc: hylafax-users@xxxxxxxxxxx
- Date: Tue, 18 Jul 2006 14:43:41 +0300
Lee Howard wrote:
You'll need to turn up SessionTracing in your modem config file to 0xFFF in order for us to really see what the matter is.Please find below the log file with SessionTracing 0xFFF as advised.
Thanks,
Lee.
Thanks for your help.
Mufit
Sender: 02324214200
Pages: 3
Quality: Normal
Size: ISO A4
Received: 2006:07:18 14:20:54
Time To Receive: 1:52
Signal Rate: 9600 bit/s
Data Format: 2-D MR
Error Correct: No
Received On: ttyS0The full document was not received because:
Failure to raise V.21 transmission carrier.
---- Transcript of session follows ----
Jul 18 14:20:27.80: [ 9802]: SESSION BEGIN 000001104 902324867470
Jul 18 14:20:27.81: [ 9802]: HylaFAX (tm) Version 4.3.0
Jul 18 14:20:27.81: [ 9802]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Jul 18 14:20:27.81: [ 9802]: <-- [13:AT+FCLASS=1A\r]
Jul 18 14:20:33.00: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:33.00: [ 9802]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jul 18 14:20:33.00: [ 9802]: STATE CHANGE: ANSWERING -> RECEIVING
Jul 18 14:20:33.00: [ 9802]: RECV FAX: begin
Jul 18 14:20:33.09: [ 9802]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 CC 74 0C>
Jul 18 14:20:33.16: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:33.16: [ 9802]: <-- HDLC<23:FF C0 02 EC 04 6C 1C 2C 04 4C CC 4C 0C 04 1E 86 62 04 2A 4A 82 72 F2>
Jul 18 14:20:33.88: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:33.88: [ 9802]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Jul 18 14:20:36.15: [ 9802]: --> [2:OK]
Jul 18 14:20:36.15: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:20:43.15: [ 9802]: --> [0:]
Jul 18 14:20:43.15: [ 9802]: MODEM <Empty line>
Jul 18 14:20:43.15: [ 9802]: MODEM TIMEOUT: waiting for v.21 carrier
Jul 18 14:20:43.15: [ 9802]: --> [2:OK]
Jul 18 14:20:43.15: [ 9802]: DELAY 1500 ms
Jul 18 14:20:44.65: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:20:44.69: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:44.69: [ 9802]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 CC 74 0C>
Jul 18 14:20:44.86: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:44.86: [ 9802]: <-- HDLC<23:FF C0 02 EC 04 6C 1C 2C 04 4C CC 4C 0C 04 1E 86 62 04 2A 4A 82 72 F2>
Jul 18 14:20:45.58: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:45.58: [ 9802]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Jul 18 14:20:47.84: [ 9802]: --> [2:OK]
Jul 18 14:20:47.84: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:20:48.79: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:50.19: [ 9802]: --> HDLC<25:FF C0 C2 0C 0C 4C 2C 8C 4C 2C 4C CC 4C 0C 04 04 04 04 04 04 04 04 04 E6 C3>
Jul 18 14:20:50.19: [ 9802]: --> [2:OK]
Jul 18 14:20:50.19: [ 9802]: REMOTE TSI "02324214200"
Jul 18 14:20:50.19: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:20:50.20: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:50.51: [ 9802]: --> HDLC<9:FF C8 C1 00 61 1F 00 3E CD>
Jul 18 14:20:50.51: [ 9802]: --> [2:OK]
Jul 18 14:20:50.51: [ 9802]: REMOTE wants 9600 bit/s
Jul 18 14:20:50.51: [ 9802]: REMOTE wants A4 page width (215 mm)
Jul 18 14:20:50.51: [ 9802]: REMOTE wants unlimited page length
Jul 18 14:20:50.51: [ 9802]: REMOTE wants 3.85 line/mm
Jul 18 14:20:50.51: [ 9802]: REMOTE wants 2-D MR
Jul 18 14:20:50.51: [ 9802]: RECV training at v.29 9600 bit/s
Jul 18 14:20:50.51: [ 9802]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Jul 18 14:20:50.51: [ 9802]: <-- [10:AT+FRM=96\r]
Jul 18 14:20:51.11: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:52.68: [ 9802]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 18 14:20:52.68: [ 9802]: RECV: TCF 1892 bytes, 3% non-zero, 1828 zero-run
Jul 18 14:20:52.69: [ 9802]: --> [10:NO CARRIER]
Jul 18 14:20:52.69: [ 9802]: <-- [9:AT+FRS=7\r]
Jul 18 14:20:52.79: [ 9802]: --> [2:OK]
Jul 18 14:20:52.79: [ 9802]: TRAINING succeeded
Jul 18 14:20:52.79: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:20:52.98: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:52.98: [ 9802]: <-- HDLC<3:FF C8 21>
Jul 18 14:20:54.16: [ 9802]: --> [2:OK]
Jul 18 14:20:54.16: [ 9802]: <-- [10:AT+FRM=96\r]
Jul 18 14:20:54.74: [ 9802]: --> [7:CONNECT]
Jul 18 14:20:54.74: [ 9802]: MODEM input buffering enabled
Jul 18 14:20:54.74: [ 9802]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Jul 18 14:20:54.74: [ 9802]: RECV: begin page
Jul 18 14:21:21.50: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1171, got 0, expected 1728
Jul 18 14:21:21.50: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1172, got 0, expected 1728
Jul 18 14:21:21.50: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1173, got 0, expected 1728
Jul 18 14:21:21.50: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1174, got 0, expected 1728
Jul 18 14:21:21.92: [ 9802]: RECV/CQ: Adjusting for RTC found at row 1171
Jul 18 14:21:21.92: [ 9802]: RECV: 1171 total lines, 0 bad lines, 0 consecutive bad lines
Jul 18 14:21:21.92: [ 9802]: RECV: end page
Jul 18 14:21:21.92: [ 9802]: --> [10:NO CARRIER]
Jul 18 14:21:21.92: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:21:22.14: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:23.23: [ 9802]: --> HDLC<5:FF C8 F2 AC A0>
Jul 18 14:21:23.23: [ 9802]: --> [2:OK]
Jul 18 14:21:23.23: [ 9802]: RECV recv MPS (more pages, same document)
Jul 18 14:21:23.23: [ 9802]: <-- [9:AT+FRS=7\r]
Jul 18 14:21:23.43: [ 9802]: --> [2:OK]
Jul 18 14:21:23.43: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:21:23.73: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:23.73: [ 9802]: RECV send MCF (message confirmation)
Jul 18 14:21:23.73: [ 9802]: RECV FAX (000001104): from 02324214200, page 1 in 0:48, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 18 14:21:23.73: [ 9802]: <-- HDLC<3:FF C8 31>
Jul 18 14:21:24.90: [ 9802]: --> [2:OK]
Jul 18 14:21:24.90: [ 9802]: <-- [10:AT+FRM=96\r]
Jul 18 14:21:26.27: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:26.27: [ 9802]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Jul 18 14:21:26.27: [ 9802]: RECV: begin page
Jul 18 14:21:52.90: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1171, got 0, expected 1728
Jul 18 14:21:52.90: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1172, got 0, expected 1728
Jul 18 14:21:52.90: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1173, got 0, expected 1728
Jul 18 14:21:52.90: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1174, got 0, expected 1728
Jul 18 14:21:53.25: [ 9802]: RECV/CQ: Adjusting for RTC found at row 1171
Jul 18 14:21:53.25: [ 9802]: RECV: 1171 total lines, 0 bad lines, 0 consecutive bad lines
Jul 18 14:21:53.25: [ 9802]: RECV: end page
Jul 18 14:21:53.25: [ 9802]: --> [10:NO CARRIER]
Jul 18 14:21:53.25: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:21:53.69: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:54.56: [ 9802]: --> HDLC<5:FF C8 F2 AC A0>
Jul 18 14:21:54.56: [ 9802]: --> [2:OK]
Jul 18 14:21:54.56: [ 9802]: RECV recv MPS (more pages, same document)
Jul 18 14:21:54.56: [ 9802]: <-- [9:AT+FRS=7\r]
Jul 18 14:21:54.76: [ 9802]: --> [2:OK]
Jul 18 14:21:54.76: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:21:55.06: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:55.06: [ 9802]: RECV send MCF (message confirmation)
Jul 18 14:21:55.06: [ 9802]: RECV FAX (000001104): from 02324214200, page 2 in 0:32, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 18 14:21:55.06: [ 9802]: <-- HDLC<3:FF C8 31>
Jul 18 14:21:56.23: [ 9802]: --> [2:OK]
Jul 18 14:21:56.23: [ 9802]: <-- [10:AT+FRM=96\r]
Jul 18 14:21:57.58: [ 9802]: --> [7:CONNECT]
Jul 18 14:21:57.58: [ 9802]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Jul 18 14:21:57.58: [ 9802]: RECV: begin page
Jul 18 14:22:24.76: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1177, got 0, expected 1728
Jul 18 14:22:24.76: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1178, got 0, expected 1728
Jul 18 14:22:24.76: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1179, got 0, expected 1728
Jul 18 14:22:24.76: [ 9802]: RECV/CQ: Bad 1D pixel count, row 1180, got 0, expected 1728
Jul 18 14:22:25.16: [ 9802]: RECV/CQ: Adjusting for RTC found at row 1177
Jul 18 14:22:25.16: [ 9802]: RECV: 1177 total lines, 0 bad lines, 0 consecutive bad lines
Jul 18 14:22:25.17: [ 9802]: RECV: end page
Jul 18 14:22:25.17: [ 9802]: --> [10:NO CARRIER]
Jul 18 14:22:25.17: [ 9802]: <-- [9:AT+FRH=3\r]
Jul 18 14:22:25.70: [ 9802]: --> [7:CONNECT]
Jul 18 14:22:26.48: [ 9802]: --> HDLC<5:FF C8 F2 AC A0>
Jul 18 14:22:26.48: [ 9802]: --> [2:OK]
Jul 18 14:22:26.48: [ 9802]: RECV recv MPS (more pages, same document)
Jul 18 14:22:26.48: [ 9802]: <-- [9:AT+FRS=7\r]
Jul 18 14:22:26.68: [ 9802]: --> [2:OK]
Jul 18 14:22:26.68: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:22:56.68: [ 9802]: MODEM TIMEOUT: reading line from modem
Jul 18 14:22:56.68: [ 9802]: MODEM <Timeout>
Jul 18 14:22:56.68: [ 9802]: RECV FAX (000001104): recvq/fax000000946.tif from 02324214200, route to <unspecified>, 2 pages in 2:23
Jul 18 14:22:56.68: [ 9802]: RECV FAX: Failure to raise V.21 transmission carrier.
Jul 18 14:22:56.68: [ 9802]: <-- [9:AT+FTH=3\r]
Jul 18 14:22:56.92: [ 9802]: --> [8:AT+FTH=3]
Jul 18 14:22:56.92: [ 9802]: RECV FAX (000001104): session with 02324214200 terminated abnormally: Failure to raise V.21 transmission carrier.
Jul 18 14:22:56.92: [ 9802]: RECV FAX: bin/faxrcvd "recvq/fax000000946.tif" "ttyS0" "000001104" "Failure to raise V.21 transmission carrier."
Jul 18 14:22:56.92: [ 9802]: RECV FAX: end
Jul 18 14:22:56.92: [ 9802]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Prev by Date: [hylafax-users] permissions - chroot ? - faxrcvd
- Next by Date: Re: [hylafax-users] Failed to properly d
- Previous by thread: [hylafax-users] permissions - chroot ? - faxrcvd
- Next by thread: Re: [hylafax-users] Which Distro offers a working Email-to-fax and fax-to-Email gateway ?
- Index(es):
Project hosted by iFAX Solutions