[hylafax-users] FW: Hylafax sending issue

["Chris Duncan" <hylafax@xxxxxxxxx>]

After more reading this may be more helpful, any ideas? (this is the log from /var/spool/hylafax/log/)

 

Thanks

 

Jul 06 11:36:55.26: [23736]: SESSION BEGIN 000000024 16148714848

Jul 06 11:36:55.26: [23736]: HylaFAX (tm) Version 4.3.0

Jul 06 11:36:55.26: [23736]: SEND FAX: JOB 6 DEST 16148714848 COMMID 000000024 DEVICE '/dev/ttyIAX' FROM 'Andy <Andy@localhost>' USER Andy

Jul 06 11:36:55.26: [23736]: STATE CHANGE: RUNNING -> SENDING

Jul 06 11:36:55.26: [23736]: <-- [12:AT+FCLASS=1\r]

Jul 06 11:36:55.26: [23736]: --> [2:OK]

Jul 06 11:36:55.26: [23736]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled

Jul 06 11:36:55.26: [23736]: DIAL 16148714848

Jul 06 11:36:55.26: [23736]: <-- [16:ATDT16148714848\r]

Jul 06 11:37:06.81: [23736]: --> [7:CONNECT]

Jul 06 11:37:07.43: [23736]: --> [10:NO CARRIER]

Jul 06 11:37:07.43: [23736]: MODEM No carrier

Jul 06 11:37:07.43: [23736]: <-- [9:AT+FRS=7\r]

Jul 06 11:37:07.44: [23736]: --> [2:OK]

Jul 06 11:37:07.44: [23736]: <-- [9:AT+FTH=3\r]

Jul 06 11:37:07.45: [23736]: --> [7:CONNECT]

Jul 06 11:37:07.45: [23736]: <-- HDLC<3:FF C8 D8>

Jul 06 11:37:07.45: [23736]: <-- data [3]

Jul 06 11:37:07.45: [23736]: <-- data [2]

Jul 06 11:37:08.92: [23736]: --> [2:OK]

Jul 06 11:37:08.92: [23736]: SEND send CRP (command repeat)

Jul 06 11:37:08.92: [23736]: <-- [9:AT+FRH=3\r]

Jul 06 11:37:12.79: [23736]: --> [7:CONNECT]

Jul 06 11:37:14.05: [23736]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>

Jul 06 11:37:14.05: [23736]: --> [2:OK]

Jul 06 11:37:14.05: [23736]: REMOTE NSF "AD 00 36 A0 00 00 00 00"

Jul 06 11:37:14.05: [23736]: NSF remote fax equipment: HP

Jul 06 11:37:14.05: [23736]: <-- [9:AT+FRH=3\r]

Jul 06 11:37:14.75: [23736]: --> [7:CONNECT]

Jul 06 11:37:14.75: [23736]: --> HDLC<25:FF C0 02 1C 2C 1C 2C 04 8C EC 1C 04 2C 8C 6C 04 04 04 04 04 04 04 04 29 92>

Jul 06 11:37:14.75: [23736]: --> [2:OK]

Jul 06 11:37:14.75: [23736]: REMOTE CSI "614 871 4848"

Jul 06 11:37:14.75: [23736]: <-- [9:AT+FRH=3\r]

Jul 06 11:37:15.19: [23736]: --> [7:CONNECT]

Jul 06 11:37:15.19: [23736]: --> HDLC<15:FF C8 01 04 77 1F 23 01 49 01 01 19 00 97 91>

Jul 06 11:37:15.29: [23736]: --> [2:OK]

Jul 06 11:37:15.29: [23736]: REMOTE best rate 33600 bit/s

Jul 06 11:37:15.29: [23736]: REMOTE max A4 page width (215 mm)

Jul 06 11:37:15.29: [23736]: REMOTE max unlimited page length

Jul 06 11:37:15.29: [23736]: REMOTE best vres 300 x 300 dpi

Jul 06 11:37:15.29: [23736]: REMOTE format support: MH, MR, MMR, JPEG Full-Color

Jul 06 11:37:15.29: [23736]: REMOTE supports T.30 Annex A, 256-byte ECM

Jul 06 11:37:15.29: [23736]: REMOTE best 0 ms/scanline

Jul 06 11:37:15.29: [23736]: USE 14400 bit/s

Jul 06 11:37:15.29: [23736]: USE error correction mode

Jul 06 11:37:15.29: [23736]: <-- [9:AT+FTH=3\r]

Jul 06 11:37:15.30: [23736]: --> [7:CONNECT]

Jul 06 11:37:15.30: [23736]: <-- HDLC<3:FF C8 DF>

Jul 06 11:37:15.30: [23736]: <-- data [3]

Jul 06 11:37:15.30: [23736]: <-- data [2]

Jul 06 11:37:16.78: [23736]: --> [2:OK]

Jul 06 11:37:16.78: [23736]: MODEM input buffering enabled

Jul 06 11:37:16.78: [23736]: <-- [5:ATH0\r]

Jul 06 11:37:16.89: [23736]: --> [2:OK]

Jul 06 11:37:16.89: [23736]: MODEM set DTR OFF

Jul 06 11:37:16.89: [23736]: MODEM set baud rate: 0 baud (flow control unchanged)

Jul 06 11:37:16.89: [23736]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)

Jul 06 11:37:16.89: [23736]: SESSION END

 

---

From: Chris Duncan [mailto:hylafax@xxxxxxxxx]
Sent: Thursday, July 06, 2006 11:32 AM
To: 'hylafax-users@xxxxxxxxxxx'
Subject: Hylafax sending issue

 

Anyone have an idea why I would get this? I’m just trying to send a fax out via winprinthylafax (simple windows client to send out fax’s). I can send a fax out manually via command line but not via this interface, anyone have any insight? Thanks

 

 

Jul  6 11:27:58 localhost FaxSend[23553]: MODEM input buffering disabled

Jul  6 11:27:58 localhost FaxSend[23553]: SEND FAX: JOB 5 DEST 16148714848 COMMID 000000023 DEVICE '/dev/ttyIAX2' FROM 'andy <andy@$domain>' USER andy

Jul  6 11:28:24 localhost FaxQueuer[18473]: NOTIFY: bin/notify "doneq/q5" "failed" "0:36"

Jul  6 11:28:24 localhost FaxQueuer[18473]: NOTIFY exit status: 0 (23556)

 

Then proceeds

 

Jul  6 11:28:49 localhost FaxGetty[18482]: MODEM set DTR OFF

Jul  6 11:28:49 localhost FaxGetty[18482]: MODEM set baud rate: 0 baud (flow control unchanged)

Jul  6 11:28:49 localhost FaxGetty[18482]: DELAY 75 ms

Jul  6 11:28:49 localhost FaxGetty[18482]: MODEM set DTR ON

Jul  6 11:28:49 localhost FaxGetty[18482]: DELAY 2600 ms

Jul  6 11:28:53 localhost FaxGetty[18482]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF

Jul  6 11:28:53 localhost FaxGetty[18482]: DELAY 10 ms

Jul  6 11:28:53 localhost FaxGetty[18482]: MODEM flush i/o

Jul  6 11:28:53 localhost FaxGetty[18482]: <-- [4:ATZ\r]

Jul  6 11:28:53 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:53 localhost FaxGetty[18482]: DELAY 3000 ms

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM flush i/o

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATH1\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [4:ATH1]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [10:AT+VCID=1\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [9:AT+VCID=1]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [7:ATS0=0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [6:ATS0=0]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATE0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [4:ATE0]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATV1\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATQ0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [7:ATS8=2\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [8:ATS7=60\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [12:AT+FCLASS=?\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [7:0,1,1.0]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports "Data"

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports "Class 1"

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports "Class 1.0"

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [12:AT+FCLASS=1\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATI3\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [19:www.soft-switch.org]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM: Mfr www.soft-switch.org

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATI0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [7:spandsp]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM: Model spandsp

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [9:AT+FTM=?\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [39:24,48,72,73,74,96,97,98,121,122,145,146]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 3.85 line/mm

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 7.7 line/mm

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 15.4 line/mm

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports R16 x 15.4 line/mm

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 200 x 100 dpi

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 200 x 200 dpi

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 200 x 400 dpi

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 300 x 300 dpi

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 2400 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 4800 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 7200 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 9600 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 12000 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 14400 bit/s

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports A4 page width (215 mm)

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports B4 page width (255 mm)

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports A3 page width (303 mm)

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports A4 page length (297 mm)

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports B4 page length (364 mm)

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports unlimited page length

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 1-D MH

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 2-D MR

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 2-D MMR

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports no ECM

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports T.30 Annex A, 64-byte ECM

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports T.30 Annex A, 256-byte ECM

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 0 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 5 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 10 ms, 5 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 10 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 20 ms, 10 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 20 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 40 ms, 20 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM Supports 40 ms/scanline

Jul  6 11:28:56 localhost FaxGetty[18482]: MODEM WWW.SOFT-SWITCH.ORG spandsp/

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATM0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [9:AT+FAR=1\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: <-- [5:ATH0\r]

Jul  6 11:28:56 localhost FaxGetty[18482]: --> [2:OK]

Jul  6 11:28:56 localhost FaxGetty[18482]: STATE CHANGE: LOCKWAIT -> RUNNING (timeout 30)