HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Reject TCF (using hylafax 4.3.0.4)



Hi,

I'm currently using hylafax+ 4.3.0.4 and still found this TCF Error. My modem config and log of TCF error are attached in this mail.
Please help how to fix it.


Thank you in advance.
Jun 22 11:54:29.33: [ 7241]: SESSION BEGIN 000001767 62271716247
Jun 22 11:54:29.33: [ 7241]: HylaFAX (tm) Version 4.3.0.4
Jun 22 11:54:29.33: [ 7241]: <-- [4:ATA\r]
Jun 22 11:54:35.35: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:35.35: [ 7241]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Jun 22 11:54:35.35: [ 7241]: RECV FAX: begin
Jun 22 11:54:35.35: [ 7241]: <-- data [34]
Jun 22 11:54:35.35: [ 7241]: <-- data [2]
Jun 22 11:54:37.43: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:37.43: [ 7241]: <-- data [23]
Jun 22 11:54:37.43: [ 7241]: <-- data [2]
Jun 22 11:54:38.26: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:38.26: [ 7241]: <-- data [13]
Jun 22 11:54:38.26: [ 7241]: <-- data [2]
Jun 22 11:54:38.91: [ 7241]: --> [2:OK]
Jun 22 11:54:38.91: [ 7241]: <-- [9:AT+FRH=3\r]
Jun 22 11:54:41.92: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:43.88: [ 7241]: --> [2:OK]
Jun 22 11:54:43.88: [ 7241]: REMOTE TSI "62 31 8432186"
Jun 22 11:54:43.88: [ 7241]: <-- [9:AT+FRH=3\r]
Jun 22 11:54:43.89: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:44.15: [ 7241]: --> [2:OK]
Jun 22 11:54:44.15: [ 7241]: REMOTE wants 9600 bit/s
Jun 22 11:54:44.15: [ 7241]: REMOTE wants A4 page width (215 mm)
Jun 22 11:54:44.15: [ 7241]: REMOTE wants unlimited page length
Jun 22 11:54:44.15: [ 7241]: REMOTE wants 3.85 line/mm
Jun 22 11:54:44.15: [ 7241]: REMOTE wants 1-D MH
Jun 22 11:54:44.15: [ 7241]: RECV training at v.29 9600 bit/s
Jun 22 11:54:44.15: [ 7241]: <-- [10:AT+FRM=96\r]
Jun 22 11:54:44.47: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:46.04: [ 7241]: RECV: TCF 1861 bytes, 5% non-zero, 1761 zero-run
Jun 22 11:54:46.04: [ 7241]: --> [10:NO CARRIER]
Jun 22 11:54:46.04: [ 7241]: <-- [9:AT+FRS=7\r]
Jun 22 11:54:46.16: [ 7241]: --> [2:OK]
Jun 22 11:54:46.16: [ 7241]: TRAINING succeeded
Jun 22 11:54:46.16: [ 7241]: <-- [9:AT+FTH=3\r]
Jun 22 11:54:46.21: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:46.21: [ 7241]: <-- data [3]
Jun 22 11:54:46.21: [ 7241]: <-- data [2]
Jun 22 11:54:47.52: [ 7241]: --> [2:OK]
Jun 22 11:54:47.52: [ 7241]: <-- [10:AT+FRM=96\r]
Jun 22 11:54:50.35: [ 7241]: --> [6:+FRH:3]
Jun 22 11:54:50.72: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:52.39: [ 7241]: --> [2:OK]
Jun 22 11:54:52.39: [ 7241]: RECV recv TSI (sender id)
Jun 22 11:54:52.39: [ 7241]: REMOTE TSI "62 31 8432186"
Jun 22 11:54:52.39: [ 7241]: <-- [9:AT+FRH=3\r]
Jun 22 11:54:52.41: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:52.66: [ 7241]: --> [2:OK]
Jun 22 11:54:52.66: [ 7241]: REMOTE wants 9600 bit/s
Jun 22 11:54:52.66: [ 7241]: REMOTE wants A4 page width (215 mm)
Jun 22 11:54:52.66: [ 7241]: REMOTE wants unlimited page length
Jun 22 11:54:52.66: [ 7241]: REMOTE wants 3.85 line/mm
Jun 22 11:54:52.66: [ 7241]: REMOTE wants 1-D MH
Jun 22 11:54:52.66: [ 7241]: RECV training at v.29 9600 bit/s
Jun 22 11:54:52.66: [ 7241]: <-- [10:AT+FRM=96\r]
Jun 22 11:54:52.99: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:54.56: [ 7241]: RECV: TCF 1860 bytes, 35% non-zero, 1197 zero-run
Jun 22 11:54:54.56: [ 7241]: RECV: reject TCF (too many non-zero, max 10%)
Jun 22 11:54:54.56: [ 7241]: RECV: reject TCF (zero run too short, min 1200)
Jun 22 11:54:54.56: [ 7241]: --> [10:NO CARRIER]
Jun 22 11:54:54.56: [ 7241]: <-- [9:AT+FRS=7\r]
Jun 22 11:54:54.68: [ 7241]: --> [2:OK]
Jun 22 11:54:54.68: [ 7241]: <-- [9:AT+FTH=3\r]
Jun 22 11:54:54.74: [ 7241]: --> [7:CONNECT]
Jun 22 11:54:54.74: [ 7241]: <-- data [3]
Jun 22 11:54:54.74: [ 7241]: <-- data [2]
Jun 22 11:54:56.05: [ 7241]: --> [2:OK]
Jun 22 11:54:56.05: [ 7241]: TRAINING failed
Jun 22 11:54:56.05: [ 7241]: <-- [9:AT+FRH=3\r]
Jun 22 11:55:03.06: [ 7241]: --> [0:]
Jun 22 11:55:03.06: [ 7241]: MODEM <Empty line>
Jun 22 11:55:03.06: [ 7241]: <-- data [1]
Jun 22 11:55:03.11: [ 7241]: --> [2:OK]
Jun 22 11:55:03.11: [ 7241]: RECV FAX (000001767): recvq/fax000001646.tif from 62 31 8432186, route to <unspecified>, 0 pages in 0:28
Jun 22 11:55:03.11: [ 7241]: RECV FAX: T.30 T2 timeout, expected page not received
Jun 22 11:55:03.11: [ 7241]: <-- [9:AT+FTH=3\r]
Jun 22 11:55:03.16: [ 7241]: --> [7:CONNECT]
Jun 22 11:55:03.16: [ 7241]: <-- data [3]
Jun 22 11:55:03.16: [ 7241]: <-- data [2]
Jun 22 11:55:04.48: [ 7241]: --> [2:OK]
Jun 22 11:55:04.48: [ 7241]: RECV FAX (000001767): session with 62 31 8432186 terminated abnormally: T.30 T2 timeout, expected page not received
Jun 22 11:55:04.48: [ 7241]: RECV FAX: bin/faxrcvd "recvq/fax000001646.tif" "ttyS1" "000001767" "T.30 T2 timeout, expected page not received"
Jun 22 11:55:04.50: [ 7241]: RECV FAX: end
Jun 22 11:55:04.50: [ 7241]: SESSION END
# $Id: conexant-1.0,v 1.2 2006/01/11 17:27:16 faxguy Exp $

#
# Configuration for a Rockwell/Conexant K56 Class 1.0 modem using
# the RCV56DPF and similar chipsets.  These chipsets are generally
# flash- upgradable and appear on ISA as well as PCI.  They
# support "Class 1.0" which means that they have "adaptive receive"
# (AT+FAR=1), but not V.34.
#
#    Comtrol RocketModem II/III
#    MultiTech MT5600ZDX
#    Zoltrix FMVSP56i3
#
#
CountryCode:		62
AreaCode:		271
FAXNumber:		716247
LongDistancePrefix:	0
InternationalPrefix:	001
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		high
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"PT KONIMEX"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
PercentGoodLines:	70
MaxRecvPages:		100
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1.0	# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
Class1AdaptRecvCmd:	AT+FAR=1	# reports carrier detection mismatches
Class1TCFWaitCmd:       AT+FTS=7



Project hosted by iFAX Solutions